1998 HONDA INTEGRA reset

nsnan upeeo rlucruauon lunF, Densor lconr q,
The scan tool indicates Diagnostic Trouble Code (DTC) P1359: A problem in the Crankshaft Position,Top Dead
Cenler/Cylinder Position (cKP/TDC/CYP) sensor circuit.tPr3ssl
The MIL has been reported on.DTC P1359 is stored.
Problem verilication:1. Do the ECM Reset Procedure.2. Turn the ignition switch to theSTART {lll) positaon for 10 sec'
NOTE:. M/T: Clutch pedal must be
. A/T: Transmission in E or E
Intermittent failure, svstem isOK. Check for ooor connactionsor loos€ wi.es at C109 {CKP/TDC/CYP sensorl and ECM.
ls DTC P1359 indicated?
Check for poor connections orloose wires between the CKP/TDC/CYP sensor and the ECM.
Substitute a known-good ECMand recheck. It symptom/indica-tion goes away, replace ih6 origi-nal ECM.
PGM-FI System
Crankshaft Speed Fluctuatio(CKFI Sensor (cont'd)
ECM lnternal Circuit
\
L
I P1607 Tfre scan tool indicates Diagnostic Trouble Code (DTC) Pl607: An ECM Internal Circuit Failure A.
The MIL has been reported on.DTC P16O7 is stored.
Problem verification:1. Do the ECM Reset Procedure.2. Start the engine.3. Allow it to idle {or 5 seconds.
Inte.miftent failure, systom L OKst this iimo.ls DTC P1607 indicated?
Substitute a known-good ECMand .echeck. lf symptom/indica-tion goes away, replace the origi-nalECM.
-92

J
a
I
lF1660l Th"""untool indicates Diag nostic Trou ble code (DTC) P1660:Aproblem in theA./rf Fl data line.
Wire side of temale terminals
(conr'd)
ECM CONNECTOR C I31P}
ATCHK{BLUI
1 2 3 1l 15 6 710
11 t2 131r t5 16 1? t8'tg /21
././I l/nzex)
TCM CONNECTOR 26P (C,r2ol
7 r-T7 s 6 ;i-g-io-rrJzlil
15 16 17 / /.20 22 23 21 25 26
ATCHK IBLU)
o
ECM CONNECTOR C {31PI
Th6 MIL has been reported on.DTC P16GO is stored.
Problem verificationl1. Oo the ECM Reset Procedure.2. Turn the ignition switch OFF.3. Start the engane. Allow theengine at idle for one minute,
lntermittent failure, swtem is OKat lhis time. Check lor poor con-n€ctions or loose wires at C420ITCMI and ECM.
ls DTC P1660 indicated?
Check for an open in the wire
{ATCHK line}:1. Turn the ignition switch OFF.2. Check for continuity betweenECM connecto. terminal C19and TCM 26P connector terminal No.20.
Repair open in the wire betweenECM (Cl9) and TCM.ls there continuity?
Check tor a short in the wire{ATCHK line):1. Disconnect the ECM conoec'tor C (31P).
2- Disconnect the 26P connectorfrom the TCM.3. Check for continuity betweenbody ground and EcM connector terminal Cl9-
Repair short in the wire betweenECM lC19) and TcM.
(To page 11-94)
11-93

JP1681 | The scan tool indicates Diagnostic Trouble Code (DTC) P1681: A low voltage problem in the A/T Fl signal A
circuit.
P1682 | The scan tool indicates Diagnostic Trouble Code {DTC) Pl682: A high voltage problem in the A//T Fl signal A
circuit.
]TtOgOl fh" scan tool indicates Diagnostic Trouble Code (DTC) P1686: A low voltage problem in the A"/T Fl signal B
ctrcutt.
lFt Ogt-l fh" scan tool indicates Diagnostic Trouble Code (DTC) P1687: A high voltage problem in the A"/T Fl signal B
crrcurt.
ECM CONNECTOR C {31PI
IGRN/BLU)
Wire side of female terminals
TCM CONNECTOR {22P) {C419}Wire side of female terminals
2!a5't0
tl1213 tatat6It1a19 ,/
AFSB I I AFSA
{GRYI T- _IIGRN
@)o
2311to21 ;'15 15 17 13 13
E./ zl za
G-\
AFSIGR
\-
a
AFlGl
I
sBl
L]
r@!I AFSA
| {GRN/lRt ltl
iFSGRIA[/BLUt
12 3 a 5 6 7 89
tz /'tt //t't /ts zo
to ,/
DTC P1681, P1682, P1686 end/or P'1687 are stored.
Problem verificetion:1. Do the ECM Reset Procedure.2. orive the car for several milesso that the transmissionupshifts and downshifts severarlrmes.
Intormittent lailure. system is OKat thi3 tim€. Check tor ooo. con-nections or loo3o wir6s al C419{TCM} .nd ECM.
ls DTC P1681, P1682, Pl686and/or P1687 indicated?
Check tor a short in th6 wires{AFSA, AFSB linel:1. Turn the ignition switch OFF.2, Disconnect the 22P connectorfrom the TCM.3. Disconnect the ECM conn6c-tor C (31P).
4. Check for continuity betweenbody ground and ECM con-nector terminal C28 (C27)*.
Rcoair 3hort in tho wiros betweenECM lC28 or C27*l rnd TCM.ls there continuity?
Check fo. an open in the wiresIAFSA, AFSB lines):Check for continuity between ECMconnector terminal C28 (C27)* andTCM 22P connector terminal No. 7(No.6i*.
Repai. opsn in the wiros bdtweenECM lC28 or C27'l and TCM.
Subsiiiutg a known-good ECMend r6ch€ck. lf 3ymptom/indica-tion goes away, repl.c6 the origi-nal ECM.
":DTC P1686 or Pl687 (NT Fl sisnal 8l
1 1-95

ldle Speed Setting
IDLEADJUSTINGSCREW
7.
6.Turn the ignition switch OFF.
Reconnect the 2P connectors to the IAC valve and
the EVAP purge control solenoid valve, then do the
ECM reset procedures.
Restart and idle the engine with no-load conditions
for one minute, then check the idle speed.
NOTE: (Canada) Pullthe parking brake lever up.
Start the engine, then check that the headlights are off.
ldle speed should be;
Bl88l €ngine:
Mfi750 i 50 rpm
A/T750150 rpm (in Park or neutral)
818C1 engine:750 i 50 rpm
818C5 engine: 800 i 50 rpm
NOTE: 81881, Bl8Cl engines - It the idle speed
increases to *1rpm, this means the EVAP system ispurging the canister. To stop the purging termporarily.
raise the engine speed above 1,000 rpm with the
accelerator pedal, then slowly release the pedal.
*1: 81881 engine
M/T: 820 i 50 rpm
Ay'T: 840 t 50 rpm
818Cl engine
850 I 50 rpm
(cont'd)
Inspection/Adiustmont
NOTE:
. When setting the idle speed, checkthe following items:- The MIL has not been reported on.- lgnition timing
Spark plugs- Air cleaner- PCV system
. (Canada) Pull the parking brake lever up. Start the
engine, then check that the headlights are off.
1. Start the engine. Hold the engine at 3,000 rpm with
no load (in Park or neutral) until the radiator fan
comes on, then let it idle,
Connect a tachometer.
Disconnect the 2P connectors from the ldle Air
Control (lAC) valve and the EVAP purge control
solenoid valve.
2.
5.
if the engine stalls, restan the engine with the accel
erator pedal slightly depressed. Stabilize the rpm at
1,000, then slowly release the pedal until the engine
idles.
Check idling in no-load conditions: headlights, blower
fan, rear defogger, radiator fan, and air conditioner
are not ope€tlng.
ldlo speed should be;
B188l engine:
Mlf480 :l 50 rpm
A/T480 i 50 rpm (in Park or neutral)
B18C1 engine: /t80 t 50 rpm
818C5 sngine:550 t 50 rpm
lf necessary, adjust the idle speed, by turning theidle adjusting screw.
After adjusting the idle speed, recheck the ignition
timing {see section 23). lf it is out of spec, go back
to steo 4.

The fuel supply system co
high pressure fuel pump, t
fuel pressure regulator. f
damper, and fuel delivery i
delivers pressure-regulated
cuts the luel delivery when
Fuel Supply System
System Description
consists of a fuel tank, in-tank
r, PGM-Fl main relay, fueffilter,
. fuel injectors, fuel pulsation
y and return lines. This system
ed fuel to the fuel injectors and
rn thq engine is not running.
Fuel Pressure
Relieving
Before disconnecting fuel pipes or hoses, release pres-
sure from the system by loosening the 12 mm banjo
bolt on top ol the fuel filter.
Do not smok€ while working on the tuel system,
Keep open flames or sparks away from you. work
arga.
Be sure to relieve fuel pressure while the ignition
swiich is ofl,
Make sure you have the anti theft code for the
radio, then write down the frequencies for the
radio's preset buttons.
Disconnect the battery negative cable from the bat-
tery negative terminal.
Remove the fuelfill cap.
Use a box end wrench on the 12 mm banjo bolt at
the fuel filter while holding the fuel filter with another
wrench.
Place a rag or shop towel over the '12 mm banjo
bolt.
Slowly loosen the 12 mm banjo bolt one complete
tu rn.
1 1-1 18
I
NOTE| Replace the washers whenever the 12 mm banjo
bolt is loosened or removed.
lnsDection
1. Relieve fuel pressure.
2. Remove the 12 mm banjo bolt from the fuel filter
while holding the fuel tilter with another wrench.
Attach the fuel pressure adapter bolt, 12 mm and
the special tool.
3. Stan the engine. Measure the tuel pressure with the
engine idling and the vacuum hose of the fuel pres-
sure regulator disconnected from the fuel pressure
regulator and pinched. lf the engine will not start,
turn the ignition switch ON (ll), wait for two sec-
onds, turn it off, then back on again and read the
tuel pressure.
Pressuro should be:
Bl8Bl engire:
270 - 320 kP. (2.8 - 3.3 kgl/cm'.40 - 47 psi)
818C1, 818C5 engines:
320 - 370 kPa (3.3 - 3.8 kgt/cm'. 47 - g psi)
12 mm
FUEL FILTER

Three Way Catalytic Converter (TWC)
lT042O I Th" """n tool indicates Diagnostic Trouble Code (DTC) P0420: catatyst system efficiency below threshold.
Descriotion
This system evaluates the catalyst's capacity by means of the HO2S (Primary and Secondary) output during stable drivingconditions. lf deterioration has been detected during three consecutive driving cycles, the MIL comes on and DTC p0420 willbe stored.
NOTE: lf some of the DTCS listed below are stored at the same time as DTC PO42O. troubleshoot those DTCS tirst. thentroubleshoot DTC P0420.
P0136, P0139: Secondarv HO2S
P0141:Secondary HO2S Heater
Possible Cause
. TWC Deterioration
. Exhaust system leakage
Troubleshooting Flowchart
Problem verification:1. Do the ECM Reset Procedure.2. Start the engine. Hold theengine at 3,000 rpm with noload (in Park or neutral) untilthe radiator fan comes on,3. Connect the SCS service con,
4. Test drive 40 - 55 mph (64 -
88 km/h) for approx. two min-utes, Then decelerate Ior atleast 3 seconds with the throttle completely closed. Thenreduce the vehicle speed to35 mph (56 km/h), and try tohold it until the readinesscode comes on.
I
- The MIL has been report€d on.- OTC P0420 is stored.
Intermittent tailure, sFtem is OKat this time.ls DTC P0420 indicated?
Check the TWC {s6e 3ection 91.lf necessary, reolace the TWC.
11-139

lT
Emission Control System
YES
{To page 11-143}
Fu€l Tank Pressure Sensor
The scan tool indicates Diagnostic Trouble Code (DTC) P0452: A low voltage problem in the Fuel Tank Pressure
sensor.
The fuel tank pressure sensor converts tuel tank absolute pressure into electrical signals and inputs the ECM.
Evaporative Emission (EVAP) Controls (cont'dl
OUTPUTVOLTAGE(vl
4.5
0.5-7 kPel-50 mmHg,-2 in.Hgl
+7 lPe
l5o mmHg,2 in.Hgl
PRESSURE
\*
Eclrl CONNECToR o {lEPl
PTANK(wltT/BLul
vcc2IYEL/BLU}
Wire side of lemale terminals
FUEL TANKPRESSURE SENSOR
3P CONNECTOR (C792)
The MIL ha3 beon roportod on.OTC F0452 i3 storad.
Chock the vscuum lines:Check the vacuum lines otthe fueltank pressure sensor for misrout-ing, leakage, breakage and clog-ging.
Are the vacuum lines OK?
Problgm verilication:1. Do the ECM Reset Procedure.2. Remove the fuel fill cap.3. Turn the ignition switch ON lll).4. Monitor the FTP sensor volt-age with the Honda PGMTester, or measure voltagebotween body ground and' ECM connector terminal D15.Int6rmittent tailure, 3ystem i3 OKat thb tirn6. Chock lor poor con-n.clions or loo3e wire3 ot C421{locltod rbovo under-d!.h fuso/r.lay boxl, C510 lloc.ted undo.rcc.rs panoll, C?92 Ituel trnko.6sura i€nior I lnd ECM.
ls there approx.2.5 V?
Check to. an opon in wi.a {VCC2line):1. Turn the ignition switch OFF.2. Reinstall the fuel fill cap.3. Disconnect the luel tank pres'su re sensor 3P connector.4. Turnthe ignition switch ON (ll).
5. Measure voltage between thetuel tank pressure sensor 3Pconnector terminals No, 1 andNo.2.
R.pai. opcn in thg wir6 bdtwoonthc fual tank pro$ure 3enlor andtho EcM lDlo).ls there approx. 5 V?
11-142
Wire side oI temale terminals

rI
Emission Control System
Evaporative Emission (EVAPI Controls (cont'd)
Fuel Tank Pre$ure sensor
The scan tool indicates Diagnostic Trouble Code (DTC) P0453: A high voltage problem in the Fuel Tank Pressure
sensor.
ECM OONNECTOR D IT6PI
PTANKILT GRNI
Wire side of female terminals
FUEL TANKPRESSURE SENSOR3P CONNECTOR {C7921
\
voc2
{YEL/BLU}
sG2IGBN/BI.KI
Wire side of female terminals
The Mll- hes bson.opofiad on.DTC m453 b stored.
Check ihe vacuum lino3:Check the vacuum Iines ot the{uel tank pressure sensor for mis-routing, leakage, breakage andcroggrng.
Are the vacu!m lin€s OK?
Problem vsrification:1. Do the ECM Reset Procedure.2. Remove the fuel fill cap.3. Turn the ignition switch ON {ll).4. Monitor the FTP sensor volt-age with the Honda PGMTester, or measure voltagebetween body ground andECM connector terminal D15.Intormittont failu.e. syst6m is OK
at ihi3 time, Chack for poor con.nections or loo3e wires at C421{locatod abovo undel-dash fu3e/rolay box), C510 (loc.ted undoracc6s3 Dan6ll, C792 Ituol trnkDro.su.6 sen3or l and ECM,
ls there approx. 2.5 V?
Check tor an open in the wire(SG2 lino):1. Turn the ignition switch OFF.2. Reinstall the fuel fill cap.3. Disconnect the fuel tank pres-
sure sensor 3P connector.4. Turn the ignition switch ON {ll}.5. Measure voltage between thetuel tank pressure sensor 3Pconnector terminals No. 1 andNo.2.
Rcpair opon in the wire b6tw66nthe fu6l tank prasSuaa 36n3or endECM {Dr1).ls there approx. 5 V?
Check lor a short in tho wirc{PTANK linel:Measure voltage between thefueltank pressure sensor 3P con-nector terminals No. 2 and No. 3.
YES
sG2IGRN/BLKI
PTANKILT GRNI
{To page 1l-145)
11-144