1998 FORD WINDSTAR belt

12
% [IS02700(ALL)12/95]
Anti-lock Brake System (ABS) Warning Light
*
[IS02800(ALL)01/96]
To check the anti-lock brake warning light, turn the ignition key
to the ON position. The ABS warning light should glow
momentarily.
*
[IS02900(ALL)01/96]
NOTE: If it does not glow at all or stays on for a long time,
have your vehicle's electrical system checked
immediately.
[IS03000(ALL)12/95]
6 pica art:0050147-B
The anti-lock brake warning light
*
[IS03100(ALL)03/96]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[IS03200(ALL)03/96]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
%*
[IS03300(ALL)03/96]
Safety Belt Warning Light and Chime
*
[IS03400(ALL)03/96]
This warning light and chime remind you to fasten your safety
belt. The following conditions will take place:
[IS03500(ALL)12/95]
n
If the driver does not fasten the safety belt before the
ignition is turned to ON, the chime will sound for four (4) to
eight (8) seconds and the light will illuminate for one (1) to
two (2) minutes, or until the safety belt is fastened.
File:03wniss.ex
Update:Fri Oct 11 10:45:38 1996

Instrumentation
13
[IS03600(ALL)12/95]
n
If the driver fastens the safety belt before the ignition is
turned to ON, the chime will not sound and the light will
not illuminate.
[IS03700(ALL)12/95]
n
If the safety belt is buckled while the light is on and the
chime is sounding, both the light and the chime turn off.
[IS03800(ALL)12/95]
6 pica art:0050148-B
The safety belt warning light
[IS03900(ALL)08/96]
Service Engine Soon Warning Light
%*
[IS04000(ALL)05/96]
This light illuminates when the engine's Emission Control
System requires service. It will also illuminate when the ignition
key is in the ON position and the engine is off.
[IS04100(ALL)08/96]
6 pica art:0050065-C
The service engine soon warning light
*
[IS04200(ALL)05/96]
Modifications or additions to the vehicle may cause incorrect
operation of the OBD II system. Additions such as burglar
alarms, cellular phones, and CB radios must be carefully
installed. Do not install these devices by tapping into or running
wires close to powertrain control system wires or components.
File:03wniss.ex
Update:Fri Oct 11 10:45:38 1996

Controls and Features
79
[CF05100(ALL)09/96]
10-1/2 pica art:0050059-E
The climate controls Ð main and auxiliary system A/C Ð Heater System Ð if
equipped
[CF05150(ALL)07/96]
The auxiliary system is controlled exclusively by the 9-position
switch. If the control is turned to the left, cool air will be
delivered at the beltline and overhead. If the control is turned
to the right, warm air will be delivered to the floor area. The
further left or right from the OFF position the control is turned,
the higher the fan speed.
[CF05200(ALL)01/96]
The standard heating system and the heating portion of the
heating and air conditioning system are essentially identical.
There is one exception, however; the air conditioning
compressor will automatically engage when theP
(DEFROST/FLOOR) orV(DEFROST) position is selected to
aid in defogging and defrosting the inside glass when the
outside temperature is above approximately45ÊF (7ÊC).Refer to
the heating system operating instructions covered previously for
a more detailed explanation of heating system operation.
File:05wncfs.ex
Update:Tue Oct 8 10:20:34 1996

135
Seating and Safety Restraints
%*
[SS00200(ALL)05/96]
Seats
*
[SS00300(ALL)01/96]
Adjusting the Seats
[SS00400(ALL)01/96]
Adjusting the front seats manually
[SS00500(ALL)01/96]
To move the front seats forward or backward:
[SS00600(ALL)01/96]1.
Find the adjustment bar at the lower cushion of the front
seat.
[SS00700(ALL)01/96]2.
Pull the bar up to unlatch the seat.
*
[SS00800(ALL)01/96]3.
Move the seat to the desired position.
*
[SS00900(ALL)01/96]4.
Release the bar to latch the seat in its new position. Make
sure the seat locks securely in place.
*
[SS01000(ALL)05/96]
RWARNING
Never adjust the driver's seat or seatback when the
vehicle is moving.
*
[SS01100(ALL)07/96]
RWARNING
Do not pile cargo higher than the seatbacks to avoid
injuring people in a collision or sudden stop.
*
[SS01200(ALL)02/96]
RWARNING
Always drive and ride with your seatback upright and
the lap belt snug and low across the hips.
*
[SS01300(ALL)05/96]
RWARNING
Children should always ride with the seatback in the
fully upright position.
File:06wnsss.ex
Update:Fri Oct 11 10:48:20 1996

136
*
[SS01350(ALL)09/96]
RWARNING
It is extremely dangerous to ride in a cargo area, inside
or outside of a vehicle. In a collision, people riding in
these areas are more likely to be seriously injured or
killed. Do not allow people to ride in any area of your
vehicle that is not equipped with seats and safety belts.
Be sure everyone in your vehicle is in a seat and using a
safety belt properly.
% [SS01400(ALL)01/96]
Using the power seats (if equipped)
[SS01500(ALL)01/96]
If your vehicle has the power seat option, you can adjust it in
several directions. The controls are on the outboard side of the
driver's seat.
[SS01600(ALL)09/96]
one third page
art:0050103-B
The power controls on the driver's seat
File:06wnsss.ex
Update:Fri Oct 11 10:48:20 1996

Seating and Safety Restraints
143
[SS04000(ALL)01/96]
Adjustable Three Passenger Bench Seat (If equipped)
[SS04100(ALL)01/96]
Your vehicle's third row passenger bench seat may be adjustable
forward and backward. This adjustment allows for additional
cargo space with the seat adjusted to the full forward position
and extra leg room when adjusted rearward.
[SS04200(ALL)01/96]
Rotate the release handle upward to unlatch. The release handle
is located on the right side of the seat near the floor. Adjust to
the desired seat position and release the handle. Make certain
the seat is latched and secure.
[SS04250(ALL)10/96]
Reclining second row bench seat
[SS04260(ALL)10/96]
To recline the bench seat, pull up on the lever located just in
front of the seat belt buckle, then push the seatback to the
desired position.
[SS04270(ALL)10/96]
17-1/2 pica
art:0051051-AFile:06wnsss.ex
Update:Fri Oct 11 10:48:20 1996

Seating and Safety Restraints
145
[SS04800(ALL)01/96]
The seat cushion will move forward when going from the seat
to the bed position.
[SS04900(ALL)09/96]
17-1/2 pica
art:0050260-B
2nd row seat (seat position)
[SS05000(ALL)01/96]
To convert the bed to a seat:
[SS05100(ALL)01/96]1.
While in front of the seat, pull the release lever up, slightly
raise the seatback, then push the seat bottom rearward until
the seatback is in the full upright and locked position.
*
[SS05200(ALL)01/96]2.
Make sure the safety belts are free and available for use.
[SS05300(ALL)04/96]
RWARNING
The seat/bed should not be occupied while the vehicle is
moving unless it is in the upright, fully-latched position.
File:06wnsss.ex
Update:Fri Oct 11 10:48:20 1996

Seating and Safety Restraints
147
[SS05900(ALL)01/96]
17-1/2 pica
art:0050261-A
3rd row seat (seat position)
[SS06000(ALL)01/96]
To convert the bed to a seat:
[SS06100(ALL)01/96]1.
From the rear of the vehicle, pull the release lever down and
at the same time lift the seatback up. Raise the seatback to
the full upright and locked position.
*
[SS06200(ALL)01/96]2.
Make sure the safety belts are free and available for use.
[SS06300(ALL)04/96]
RWARNING
The seat/bed should not be occupied while the vehicle is
moving unless it is in the upright, fully-latched position.
File:06wnsss.ex
Update:Fri Oct 11 10:48:20 1996