1998 FORD MUSTANG hood release

OPENING THE HOOD
1. Inside the vehicle,
pull the hood release
handle located under
the bottom left corner
of the instrument
panel.
2. Go to the front of the vehicle and release the
auxiliary latch that is located under the front center
of the hood.
3. Lift the hood and secure it with the prop rod.
HOOD
Maintenance and care
128

Replacing headlamp bulbs
Handle a halogen headlamp bulb carefully
and keep out of children's reach. Grasp the
bulb only by its plastic base and do not touch the
glass. The oil from your hand could cause the bulb
to break the next time the headlamps are
operated.
To remove the headlamp bulb:
1. Make sure headlamp switch is in OFF position,
then open the hood.
2. At the back of the
headlamp, pull two
retainer pins up to
release the headlamp
assembly.
3. Pull headlamp
assembly forward
disengaging the lamp
from the rear hidden snap retainers to expose the
back of the bulb.
4. Release clip and
disconnect the
electrical connector
from the bulb.
5. Remove the bulb
retaining ring by
rotating it
counterclockwise
(when viewed from the
rear) about
1¤4turn to
free it from the bulb socket, and slide the ring off
the plastic base. Keep the ring to retain the new
bulb.
6. Without turning, remove the old bulb from the
lamp assembly by gently pulling it straight out of the
lamp assembly.
Maintenance and care
166

To install the new bulb:
1. With the flat side of
the new bulb's plastic
base facing upward,
insert the glass end of
the bulb into the lamp
assembly. You may
need to turn the bulb left or right to align the
grooves in the plastic base with the tabs in the lamp
assembly. When the grooves are aligned, push the
bulb into the lamp assembly until the plastic base
contacts the rear of the lamp assembly.
2. Install the bulb retaining ring over the plastic base
until it contacts the rear of the socket by rotating
clockwise until you feel a ªstop.º
3. Connect the electrical connector into the plastic
base until it snaps, locking it into position.
4. Install the headlamp on vehicle by aligning the
lamp with the rear snap retainer, push to seat and
secure with two retainer pins.
5. Turn the headlamps on and make sure they work
properly. If the headlamp was correctly aligned
before you changed the bulb, you should not need to
align it again.
Replacing front parking lamp/turn signal bulbs
1. Make sure the headlamp control is in the OFF
position.
2. Open the hood.
3. At the back of the
headlamp, pull two
retainer pins up to
release the headlamp
assembly.
4. Pull headlamp
assembly forward
disengaging the lamp
from the rear snap retainer to expose the back of
the bulb.
Maintenance and care
167

Item Information
Recommended fuel Unleaded fuel only -
87 octane
Fuel tank capacity 58.7L (15.5 gallons)
Engine oil capacity
(includes filter change)4.7L (5.0 quarts). Use
Motorcraft 5W30 Super
Premium Motor Oil,
Ford specification
WSS-M2C153-G
Tire size and pressure See label on inside of
glove box door.
Hood release Pull handle under the
left side of the
instrument panel.
Coolant capacity-3.8L
OHV V6 engine
111.2L (11.8 quarts)
Coolant capacity-4.6L
SOHC V8 engine
113.3L (14.1 quarts)
Power steering fluid
capacityFill to line on reservoir
or dipstick. Use
Motorcraft MERCONtV
AT F.
Manual transmission
fluid capacity-3.8L OHV
V6 engine2.6L (5.6 pints). Use
Motorcraft MERCONt
AT F.
Manual transmission
fluid capacity-4.6L
SOHC V8 engine
2
3.1L (6.6 pints). Use
Motorcraft MERCONt
AT F.
Automatic transmission
fluid capacity-3.8L OHV
V6 engine
3
13.1L (13.9 quarts). Use
Motorcraft MERCONtV
AT F.
Automatic transmission
fluid capacity-4.6L
SOHC V8 engine
3
12.0L (12.8 quarts). Use
Motorcraft MERCONtV
AT F.
Filling station information
191