1998 DODGE RAM 1500 Washer

CARGO BOX - TIE DOWN
REMOVAL
(1) Remove the bolts and remove the tie down
cleat. (Fig. 4)
INSTALLATION
(1) Install the tie down cleat and install the bolts.
(2) Tighten the bolts to 34 N´m (25 ft. lbs.).
COWL GRILLE
REMOVAL
(1) Remove the wiper arms. (Refer to 8 - ELEC-
TRICAL/WIPERS/WASHERS/WIPER ARMS -
REMOVAL)
(2) Disconnect the washer hose.
(3) Remove the hood seal.
(4) Remove the six push pin fasteners from the
front of the grille. (Fig. 5)
(5) Remove the two rear corner screws and remove
the grilles.
INSTALLATION
(1) Install the grill and install the two rear corner
screws.
(2) Install the six push pin fasteners along the
front of the grille.
(3) Install the hood seal.
(4) Connect the washer hose.(5) Install the wiper arms. (Refer to 8 - ELECTRI-
CAL/WIPERS/WASHERS/WIPER ARMS - INSTAL-
LATION)
EXTERIOR NAME PLATES
REMOVAL
NOTE: Exterior name plates are attached to body
panels with adhesive tape.
(1) Apply a length of masking tape on the body,
parallel to the top edge and one end of the name
plate to use as a guide for installation, if necessary.
(2) If temperature is below 21ÉC (70ÉF) warm
emblem with a heat lamp or gun. Do not exceed 52ÉC
(120ÉF) when heating name plate.
(3) Using a trim stick C-4755 or equivalent,
remove and discard the name plate.
INSTALLATION
(1) Thoroughly clean all residue from the name
plate attachment area of the body panel.
(2) Wipe area with a clean lint free cloth moist-
ened with a 50% solution of water and alcohol and
wipe dry immediately with a dry lint free cloth.
(3) Remove protective cover from adhesive tape on
back of name plate.
(4)
Position name plate properly on the body panel.
(5) Apply consistent and uniform pressure over the
entire surface of the name plate, with palm of hand.
(6) If temperature is below 21ÉC (70ÉF) warm
emblem with a heat lamp or gun to assure adhesion.
Do not exceed 52ÉC (120ÉF) when heating name
plate.
Fig. 4 TIE DOWN CLEAT
1 - BOLTS (2)
2 - CLEAT
Fig. 5 COWL GRILLE
1 - PUSH PIN FASTENERS (6)
2 - COWL GRILLE
3 - SCREWS (2)
23 - 38 EXTERIORDR

FIRING ORDER / CABLE ROUTING, 5.7L
V-8 ENGINE..........................8I-4
FIRING ORDER, 3.7L V-6 - ENGINE........8I-4
FIRING ORDER, 4.7L V-8 - ENGINE........8I-4
FIRING ORDER, DIESEL - FUEL
INJECTOR..........................14-48
FITTING - DESCRIPTION, QUICK
CONNECT............................14-8
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING...........9-129
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING.....9-134,9-207
FITTING - STANDARD PROCEDURE,
PISTON...................9-139,9-211,9-51
FITTING - STANDARD PROCEDURE,
PISTON RING.........9-142,9-213,9-284,9-53
FITTING, STANDARD PROCEDURE -
CONNECTING ROD BEARING............9-49
FITTING, STANDARD PROCEDURE -
MAIN BEARING.......................9-44
FITTINGS - STANDARD PROCEDURE,
HANDLING TUBING...................24-45
FITTINGS - STANDARD PROCEDURE,
QUICK-CONNECT......................14-8
FLAG - INSTALLATION, SIDE VIEW
MIRROR...........................23-27
FLAG - REMOVAL, SIDE VIEW MIRROR . . . 23-27
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED....................5-10
FLARING - STANDARD PROCEDURE, ISO . . . 5-11
FLEX PLATE - INSTALLATION . . 9-138,9-210,9-48
FLEX PLATE - REMOVAL.......9-138,9-210,9-48
FLOOR - INSTALLATION, LOAD..........23-72
FLOOR - REMOVAL, LOAD.............23-71
FLOOR CONSOLE - INSTALLATION.......23-67
FLOOR CONSOLE - REMOVAL...........23-67
FLOOR DISTRIBUTION DUCT -
INSTALLATION.......................24-34
FLOOR DISTRIBUTION DUCT - REMOVAL . 24-33
FLOOR MATS - INSTALLATION, CARPETS . 23-65
FLOOR MATS - REMOVAL, CARPETS.....23-65
FLOOR SHIFT BOOT - INSTALLATION,
4WD ..............................23-62
FLOOR SHIFT BOOT - REMOVAL, 4WD....23-62
FLOOR SUPPORT CYLINDER -
INSTALLATION, LOAD.................23-72
FLOOR SUPPORT CYLINDER -
REMOVAL, LOAD.....................23-72
FLOW - 5.9L DIESEL - DESCRIPTION,
COOLING SYSTEM.....................7-3
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..............7-54,7-56
FLOW 3.7L/4.7L/5.7L ENGINE -
DESCRIPTION, COOLING SYSTEM.........7-1
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION................19-43
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-4
FLUID - DESCRIPTION, POWER
STEERING............................0-3
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT............21-201,21-366
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE........21-203,21-367
FLUID CAPACITIES, SPECIFICATIONS.......0-5
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING................21-202,21-366
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-23
FLUID COOLER - INSTALLATION.........19-43
FLUID COOLER - REMOVAL............19-43
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE.....21-441,21-476,21-507,21-537,
21-571
FLUID INDICATOR - DESCRIPTION,
WASHER
...........................8J-44
FLUID INDICATOR - OPERATION,
WASHER
...........................8J-44
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING
.........21-144,21-318
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT
.....21-201,
21-366
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE
..............................5-23FLUID LEVEL CHECK - STANDARD
PROCEDURE.................21-202,21-366
FLUID LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING........19-43
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-9
FLUID LEVEL SWITCH - INSTALLATION,
WASHER...........................8R-11
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-9
FLUID LEVEL SWITCH - REMOVAL,
WASHER...........................8R-10
FLUID RESERVOIR - INSTALLATION.......5-24
FLUID RESERVOIR - REMOVAL..........5-23
FLUID, SPECIFICATIONS - BRAKE.........5-23
FLUSH - SPECIFICATIONS, GAP.........23-95
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-40
FLYWHEEL - ASSEMBLY................6-11
FLYWHEEL - DIAGNOSIS AND TESTING....6-10
FLYWHEEL - DISASSEMBLY.............6-11
FLYWHEEL - INSTALLATION.............6-11
FLYWHEEL - REMOVAL.................6-11
FOG LAMP - INSTALLATION............8L-12
FOG LAMP - REMOVAL................8L-12
FOG LAMP RELAY - DESCRIPTION.......8L-12
FOG LAMP RELAY - INSTALLATION........8L-13
FOG LAMP RELAY - OPERATION.........8L-13
FOG LAMP RELAY - REMOVAL..........8L-13
FOOTMANS LOOP BRACKETS -
INSTALLATION, SEAT BACK REAR.......23-85
FOOTMANS LOOP BRACKETS -
REMOVAL, SEAT BACK REAR...........23-85
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE . . 9-239,9-9,
9-94
FRAME - INSTALLATION, GRILLE........23-40
FRAME - REAR - INSTALLATION, SEAT
CUSHION...........................23-85
FRAME - REAR - REMOVAL, SEAT
CUSHION...........................23-85
FRAME - REMOVAL, GRILLE............23-40
FRAME DIMENSIONS - SPECIFICATIONS . . 13-16
FRAME H-SECTION REPLACEMENT -
STANDARD PROCEDURE, REAR.........13-13
FRAME RAIL TIP REPLACEMENT -
STANDARD PROCEDURE, LIGHT DUTY
FRONT..............................13-4
FREE MODULE - INSTALLATION, HANDS . . . 8T-2
FREE MODULE - REMOVAL, HANDS.......8T-2
FRONT - INSTALLATION....5-16,5-21,5-22,5-34
FRONT - INSTALLATION...............22-14
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL.............9-136,9-208,9-275,9-46
FRONT - INSTALLATION, PROPELLER
SHAFT - HD...........................3-7
FRONT - INSTALLATION, PROPELLER
SHAFT- LD............................3-7
FRONT - INSTALLATION, SEAT..........23-81
FRONT - INSTALLATION, SEAT BACK
CUSHION / COVER...................23-82
FRONT - INSTALLATION, SEAT CUSHION
/ COVER............................23-83
FRONT - REMOVAL........5-13,5-17,5-21,5-33
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL................9-135,9-208,9-275,9-46
FRONT - REMOVAL, PROPELLER SHAFT
- HD ................................3-7
FRONT - REMOVAL, PROPELLER SHAFT-
LD ..................................3-6
FRONT - REMOVAL, SEAT..............23-81
FRONT - REMOVAL, SEAT BACK
CUSHION / COVER...................23-82
FRONT - REMOVAL, SEAT CUSHION /
COVER.............................23-83
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-2
FRONT AXLE - 9 1/4 AA -
ADJUSTMENTS
.......................3-59
FRONT AXLE - 9 1/4 AA - DIAGNOSIS
AND TESTING
........................3-54
FRONT AXLE - 9 1/4 AA - INSTALLATION
. . . 3-58
FRONT AXLE - 9 1/4 AA - REMOVAL
......3-57
FRONT AXLE - 9 1/4 AA - SPECIAL
TOOLS
..............................3-64FRONT AXLE - 9 1/4 AA -
SPECIFICATIONS......................3-63
FRONT AXLE - C205F - ADJUSTMENTS....3-32
FRONT AXLE - C205F - DIAGNOSIS AND
TESTING............................3-27
FRONT AXLE - C205F - INSTALLATION.....3-31
FRONT AXLE - C205F - REMOVAL........3-31
FRONT AXLE - C205F - SPECIAL TOOLS . . . 3-40
FRONT AXLE - C205F - SPECIFICATIONS . . . 3-39
FRONT BEARING - INSTALLATION,
OUTPUT SHAFT.....................21-216
FRONT BEARING - REMOVAL, OUTPUT
SHAFT............................21-216
FRONT BRAKE HOSE - INSTALLATION.....5-13
FRONT BUMPER - INSTALLATION.........13-2
FRONT BUMPER - REMOVAL............13-2
FRONT CENTER SEAT BELT -
INSTALLATION......................8O-31
FRONT CENTER SEAT BELT - REMOVAL . . 8O-30
FRONT CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-29
FRONT CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-29
FRONT CLUTCH - ASSEMBLY..........21-207
FRONT CLUTCH - DESCRIPTION........21-205
FRONT CLUTCH - DISASSEMBLY.......21-205
FRONT CLUTCH - INSPECTION.........21-206
FRONT CLUTCH - OPERATION.........21-205
FRONT CONTROL MODULE -
DESCRIPTION.....................8W-97-5
FRONT CONTROL MODULE -
DESCRIPTION........................8E-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING.....................8W-97-5
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING........................8E-5
FRONT CONTROL MODULE -
INSTALLATION....................8W-97-6
FRONT CONTROL MODULE -
INSTALLATION........................8E-5
FRONT CONTROL MODULE - OPERATION . 8W-97-5
FRONT CONTROL MODULE - OPERATION . . 8E-5
FRONT CONTROL MODULE - REMOVAL . 8W-97-6
FRONT CONTROL MODULE - REMOVAL....8E-5
FRONT CROSSMEMBER - INSTALLATION . . 13-22
FRONT CROSSMEMBER - REMOVAL.....13-22
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION........23-92
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL............23-92
FRONT DOOR INNER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR INNER BELT MOLDING -
REMOVAL..........................23-93
FRONT DOOR OUTER BELT MOLDING -
INSTALLATION.......................23-93
FRONT DOOR OUTER BELT MOLDING -
REMOVAL..........................23-92
FRONT FASCIA - INSTALLATION..........13-3
FRONT FASCIA - REMOVAL..............13-2
FRONT FENDER - INSTALLATION........23-39
FRONT FENDER - REMOVAL............23-39
FRONT FRAME RAIL TIP REPLACEMENT
- STANDARD PROCEDURE, LIGHT
DUTY...............................13-4
FRONT HOSE - REMOVAL...............5-12
FRONT MOUNT - INSTALLATION . . . 9-147,9-218,
9-287,9-59
FRONT MOUNT - REMOVAL . . 9-146,9-217,9-286,
9-58
FRONT OUTBOARD SEAT BELT BUCKLE -
INSTALLATION......................8O-38
FRONT OUTBOARD SEAT BELT BUCKLE -
REMOVAL..........................8O-37
FRONT OUTPUT SHAFT SEAL -
INSTALLATION . . . 21-442,21-477,21-508,21-538,
21-572
FRONT OUTPUT SHAFT SEAL -
REMOVAL . 21-441,21-477,21-507,21-537,21-572
FRONT PARKING BRAKE CABLE -
INSTALLATION........................5-38
FRONT PARKING BRAKE CABLE -
REMOVAL
...........................5-36
FRONT SEAL - INSTALLATION, OIL
PUMP
............................21-391
FRONT SEAL - REMOVAL, OIL PUMP
....21-391
FRONT SERVO - ASSEMBLY
...........21-209
FRONT SERVO - CLEANING
...........21-209
DRINDEX 13
Description Group-Page Description Group-Page Description Group-Page

HEATED SEAT MODULE - INSTALLATION . . . 8E-7
HEATED SEAT MODULE - INSTALLATION . . 8G-15
HEATED SEAT MODULE - OPERATION.....8E-6
HEATED SEAT MODULE - OPERATION....8G-14
HEATED SEAT MODULE - REMOVAL.......8E-7
HEATED SEAT MODULE - REMOVAL.....8G-15
HEATED SEAT SENSOR - DESCRIPTION . . . 8G-11
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING.......................8G-11
HEATED SEAT SENSOR - OPERATION....8G-11
HEATED SEAT SENSOR - REMOVAL......8G-11
HEATED SEAT SWITCH - DESCRIPTION . . . 8G-11
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8G-12
HEATED SEAT SWITCH - INSTALLATION . . 8G-13
HEATED SEAT SWITCH - OPERATION.....8G-12
HEATED SEAT SWITCH - REMOVAL......8G-13
HEATED SEAT SYSTEM - DESCRIPTION....8G-7
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SYSTEM - OPERATION.....8G-8
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-37
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-38
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-38
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.........................7-38
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-36
HEATER - DESCRIPTION, FUEL..........14-51
HEATER - DESCRIPTION, INTAKE AIR.....14-80
HEATER - DIAGNOSIS AND TESTING,
ENGINE BLOCK.......................7-36
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-52
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-37
HEATER - INSTALLATION, INTAKE AIR....14-80
HEATER - OPERATION, ENGINE BLOCK....7-36
HEATER - OPERATION, FUEL............14-51
HEATER - OPERATION, INTAKE AIR......14-80
HEATER - REMOVAL, ENGINE BLOCK......7-37
HEATER - REMOVAL, INTAKE AIR........14-80
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-14
HEATER CONTROL - INSTALLATION, A/C . . 24-15
HEATER CONTROL - REMOVAL, A/C......24-15
HEATER CORE - DESCRIPTION..........24-63
HEATER CORE - INSTALLATION.........24-63
HEATER CORE - OPERATION............24-63
HEATER CORE - REMOVAL.............24-63
HEATER INLET HOSE - INSTALLATION....24-64
HEATER INLET HOSE - REMOVAL........24-64
HEATER PERFORMANCE TEST -
DIAGNOSIS AND TESTING..............24-6
HEATER RELAY - DESCRIPTION, FUEL....14-52
HEATER RELAY - DESCRIPTION, INTAKE
AIR ...............................14-82
HEATER RELAY - INSTALLATION, FUEL . . . 14-53
HEATER RELAY - INSTALLATION, INTAKE
AIR ...............................14-82
HEATER RELAY - OPERATION, FUEL......14-52
HEATER RELAY - OPERATION, INTAKE
AIR ...............................14-82
HEATER RELAY - REMOVAL, FUEL.......14-52
HEATER RELAY - REMOVAL, INTAKE AIR . . 14-82
HEATER RETURN HOSE - INSTALLATION . . 24-65
HEATER RETURN HOSE - REMOVAL......24-64
HEIGHT ADJUSTMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEIGHT MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEMI ENGINE - INSTALLATION, 3.7L/4.7L
AND 5.7L......................24-59,24-73
HEMI ENGINE - REMOVAL, 3.7L/4.7L
AND 5.7L......................24-57,24-71
HIGH BEAM INDICATOR - DESCRIPTION
. . 8J-28
HIGH BEAM INDICATOR - OPERATION
....8J-28
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER
...............8L-11
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER
...................8L-11
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER
...............8L-11HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-11
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-48
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-48
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH/LOW RELAY - DESCRIPTION,
WIPER.............................8R-20
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-21
HIGH/LOW RELAY - INSTALLATION,
WIPER.............................8R-22
HIGH/LOW RELAY - OPERATION, WIPER . . 8R-20
HIGH/LOW RELAY - REMOVAL, WIPER . . . 8R-21
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-58
HINGE - INSTALLATION.....23-16,23-22,23-31,
23-46
HINGE - INSTALLATION, CENTER SEAT
BACK..............................23-79
HINGE - REMOVAL....23-16,23-22,23-31,23-46
HINGE - REMOVAL, CENTER SEAT BACK . . 23-78
HINGE COVER - INSTALLATION, CENTER
SEAT BACK INERTIA..................23-77
HINGE COVER - REMOVAL, CENTER
SEAT BACK INERTIA..................23-77
HITCH - INSTALLATION, TRAILER........13-25
HITCH - REMOVAL, TRAILER...........13-25
HOAT COOLANT - DESCRIPTION..........7-32
HOISTING - STANDARD PROCEDURE......0-20
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - OPERATION, BATTERY.....8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-51
HOLDER - REMOVAL, CUP.............23-51
HOLDING CLUTCHES - DESCRIPTION....21-371
HOLDING CLUTCHES - OPERATION.....21-372
HOLE PLUG - INSTALLATION, CAMSHAFT
CORE..............................9-206
HOLE PLUG - REMOVAL, CAMSHAFT
CORE..............................9-205
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-8
HONING - STANDARD PROCEDURE,
CYLINDER BORE.................9-128,9-38
HOOD - INSTALLATION................23-47
HOOD - REMOVAL....................23-46
HOOK - INSTALLATION, COAT...........23-66
HOOK - REMOVAL, COAT..............23-66
HOOK ASSEMBLY - INSTALLATION,
FRONT TOW........................13-23
HOOK ASSEMBLY - REMOVAL, FRONT
TOW ..............................13-23
HORN - DIAGNOSIS AND TESTING.......8H-1
HORN - INSTALLATION.................8H-2
HORN - REMOVAL....................8H-2
HORN SWITCH - DESCRIPTION..........8H-2
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-2
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - GEAR TO COOLER -
INSTALLATION, RETURN..........19-44,19-45
HOSE - GEAR TO COOLER - REMOVAL,
RETURN......................19-44,19-45
HOSE - INSTALLATION, FRONT BRAKE.....5-13
HOSE - INSTALLATION, HEATER INLET....24-64
HOSE - INSTALLATION, HEATER RETURN . 24-65
HOSE - INSTALLATION, PRESSURE . 19-44,19-45
HOSE - INSTALLATION, REAR BRAKE......5-12
HOSE - REMOVAL, FRONT..............5-12
HOSE - REMOVAL, HEATER INLET.......24-64
HOSE - REMOVAL, HEATER RETURN.....24-64
HOSE - REMOVAL, PRESSURE.....19-44,19-45
HOSE - REMOVAL, REAR BRAKE
.........5-11
HOSE - RESERVOIR TO COOLER -
INSTALLATION, RETURN
..........19-44,19-45
HOSE - RESERVOIR TO COOLER -
REMOVAL, RETURN
.............19-44,19-45
HOSE ASSEMBLY - INSTALLATION, REAR
TUBE
...............................5-13
HOSE ASSEMBLY - REMOVAL, REAR
TUBE
...............................5-12HOSE CLAMPS - DESCRIPTION...........7-3
HOSE CLAMPS - OPERATION.............7-5
HOSES/TUBES - DESCRIPTION, WASHER . 8R-11
HOSES/TUBES - OPERATION, WASHER . . . 8R-11
HOUSING - ASSEMBLY, HVAC...........24-35
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-7
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH.......6-9
HOUSING - INSTALLATION, GEAR........9-300
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - INSTALLATION, ROCKER.....9-255
HOUSING - REMOVAL, CLUTCH...........6-9
HOUSING - REMOVAL, GEAR...........9-299
HOUSING - REMOVAL, HVAC...........24-34
HOUSING - REMOVAL, ROCKER.........9-255
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION...........21-440
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION...............21-440
HOUSING COVER - INSTALLATION, GEAR . 9-301
HOUSING COVER - REMOVAL, GEAR.....9-301
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-144,21-318
HOUSING SEAL - INSTALLATION,
ADAPTER...............21-128,21-364,21-85
HOUSING SEAL - INSTALLATION,
EXTENSION . 21-128,21-201,21-507,21-536,21-85
HOUSING SEAL - REMOVAL, ADAPTER . . 21-128,
21-364,21-85
HOUSING SEAL - REMOVAL,
EXTENSION . 21-128,21-201,21-507,21-536,21-85
HOUSING SEAL AND DUST BOOT -
INSTALLATION, EXTENSION.....21-476,21-571
HOUSING SEAL AND DUST BOOT -
REMOVAL, EXTENSION.........21-476,21-571
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H-SECTION REPLACEMENT - STANDARD
PROCEDURE, REAR FRAME............13-13
HUB / BEARING - INSTALLATION.........2-32
HUB / BEARING - REMOVAL.............2-31
HVAC HOUSING - ASSEMBLY...........24-35
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-30
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING.........9-125,9-32
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-141,21-316
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS..............21-176,21-337
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING...........................9-210
HYDRAULIC TAPPETS - INSTALLATION . . . 9-211
HYDRAULIC TAPPETS - REMOVAL.......9-211
HYDROBOOST - INSTALLATION..........5-27
HYDROBOOST - INSTALLATION, ALL
EXCEPT.............................5-27
HYDROBOOST - REMOVAL..............5-26
HYDROBOOST - REMOVAL, ALL EXCEPT . . . 5-26
HYDRO-BOOST BRAKE BOOSTER -
INSTALLATION........................5-32
HYDRO-BOOST BRAKE BOOSTER -
REMOVAL
...........................5-31
HYDROFORM FENDER RAIL REPAIR -
STANDARD PROCEDURE
...............13-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
...................9-190,9-240
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-5
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE
..............Intro.-1
IDLE AIR CONTROL MOTOR -
DESCRIPTION
.......................14-28
IDLE AIR CONTROL MOTOR -
INSTALLATION
.......................14-29
IDLE AIR CONTROL MOTOR -
OPERATION
.........................14-28
IDLE AIR CONTROL MOTOR - REMOVAL
. . 14-29
IDLER SHAFT - INSTALLATION
......9-179,9-81
IDLER SHAFT - REMOVAL
..........9-179,9-81
IGNITION - SPECIFICATIONS, TORQUE
.....8I-3
16 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-10
IGNITION CIRCUIT SENSE - OPERATION . . 8E-11
IGNITION COIL - DESCRIPTION..........8I-11
IGNITION COIL - INSTALLATION.........8I-14
IGNITION COIL - OPERATION............8I-12
IGNITION COIL - REMOVAL.............8I-13
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-21
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-21
IGNITION COIL CAPACITOR - OPERATION . . 8I-21
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-21
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-5
IGNITION COIL RESISTANCE, 4.7L V-8.....8I-5
IGNITION COIL RESISTANCE, 5.7L V-8.....8I-5
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION SWITCH - DESCRIPTION........19-9
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-11
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-9
IGNITION SWITCH - INSTALLATION......19-11
IGNITION SWITCH - OPERATION.........19-9
IGNITION SWITCH - REMOVAL..........19-10
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-11
IGNITION TIMING, SPECIFICATIONS.......8I-5
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-11
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE (SKIM) -
DESCRIPTION, SENTRY KEY.............8Q-1
IMMOBILIZER MODULE (SKIM) -
OPERATION, SENTRY KEY..............8Q-2
IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY KEY......8Q-5
IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY KEY........8Q-5
IMMOBILIZER SYSTEM INITIALIZATION,
STANDARD PROCEDURE - SENTRY
KEY................................8Q-3
IMMOBILIZER SYSTEM (SKIS) -
DESCRIPTION, SENTRY KEY.............8Q-1
IMMOBILIZER SYSTEM (SKIS) -
OPERATION, SENTRY KEY..............8Q-2
IMMOBILIZER SYSTEM TRANSPONDER
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY.............8Q-4
IMPACT SENSOR - DESCRIPTION, SIDE . . 8O-59
IMPACT SENSOR - OPERATION, SIDE....8O-59
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF......21-201,21-366
INDEPENDENT FRONT SUSPENSION -
DESCRIPTION, GEAR..................19-17
INDEPENDENT FRONT SUSPENSION -
INSTALLATION, GEAR.................19-18
INDEPENDENT FRONT SUSPENSION -
REMOVAL, GEAR.....................19-17
INDICATOR - DESCRIPTION, ABS........8J-17
INDICATOR - DESCRIPTION, AIRBAG.....8J-18
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-19
INDICATOR - DESCRIPTION, CARGO
LAMP
..............................8J-20
INDICATOR - DESCRIPTION, CHECK
GAUGES
............................8J-21
INDICATOR - DESCRIPTION, CRUISE
.....8J-22
INDICATOR - DESCRIPTION, DOOR AJAR
. . 8J-23
INDICATOR - DESCRIPTION, ETC
........8J-25
INDICATOR - DESCRIPTION, GEAR
SELECTOR
..........................8J-27
INDICATOR - DESCRIPTION, HIGH BEAM
. . 8J-28
INDICATOR - DESCRIPTION, LAMP OUT
. . . 8J-29
INDICATOR - DESCRIPTION, LOW FUEL
. . . 8J-30
INDICATOR - DESCRIPTION, SEATBELT
. . . 8J-34
INDICATOR - DESCRIPTION, SECURITY
. . . 8J-35
INDICATOR - DESCRIPTION, SERVICE
4WD
...............................8J-36
INDICATOR - DESCRIPTION, TOW/HAUL
. . . 8J-39INDICATOR - DESCRIPTION, TRANS
TEMP..............................8J-40
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-40
INDICATOR - DESCRIPTION, UPSHIFT....8J-41
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-44
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-44
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-45
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-20
INDICATOR - OPERATION, ABS..........8J-17
INDICATOR - OPERATION, AIRBAG.......8J-18
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-19
INDICATOR - OPERATION, CARGO LAMP . . 8J-20
INDICATOR - OPERATION, CHECK
GAUGES............................8J-21
INDICATOR - OPERATION, CRUISE.......8J-22
INDICATOR - OPERATION, DOOR AJAR . . . 8J-23
INDICATOR - OPERATION, ETC..........8J-25
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-27
INDICATOR - OPERATION, HIGH BEAM....8J-28
INDICATOR - OPERATION, LAMP OUT....8J-29
INDICATOR - OPERATION, LOW FUEL.....8J-30
INDICATOR - OPERATION, SEATBELT.....8J-34
INDICATOR - OPERATION, SECURITY......8J-36
INDICATOR - OPERATION, SERVICE 4WD . . 8J-37
INDICATOR - OPERATION, TOW/HAUL....8J-39
INDICATOR - OPERATION, TRANS TEMP . . 8J-40
INDICATOR - OPERATION, TURN SIGNAL . . 8J-41
INDICATOR - OPERATION, UPSHIFT......8J-42
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-44
INDICATOR - OPERATION, WASHER
FLUID..............................8J-44
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-45
INDICATOR LAMP - DESCRIPTION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP - OPERATION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-31
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-31
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INERTIA HINGE COVER - INSTALLATION,
CENTER SEAT BACK..................23-77
INERTIA HINGE COVER - REMOVAL,
CENTER SEAT BACK..................23-77
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-7
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-40
INITIALIZATION, STANDARD PROCEDURE
- SENTRY KEY IMMOBILIZER SYSTEM....8Q-3
INJECTED RINGS - ASSEMBLY, WITH......3-13
INJECTED RINGS - DISASSEMBLY, WITH . . . 3-11
INJECTION PUMP - DESCRIPTION, FUEL . . 14-53
INJECTION PUMP - INSTALLATION, FUEL . 14-55
INJECTION PUMP - OPERATION, FUEL....14-53
INJECTION PUMP - REMOVAL, FUEL.....14-54
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-53
INJECTOR - DESCRIPTION, FUEL . . . 14-26,14-74
INJECTOR - INSTALLATION, FUEL........14-77
INJECTOR - OPERATION, FUEL
.....14-26,14-74
INJECTOR - REMOVAL, FUEL
...........14-75
INJECTOR FIRING ORDER, DIESEL -
FUEL
..............................14-48
INJECTOR RAIL - DESCRIPTION, FUEL
....14-78
INJECTOR RAIL - INSTALLATION, FUEL
. . . 14-78INJECTOR RAIL - OPERATION, FUEL.....14-78
INJECTOR RAIL - REMOVAL, FUEL.......14-78
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - DESCRIPTION.....14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - INSTALLATION.....14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - OPERATION.......14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - REMOVAL........14-79
INLET FILTER - INSTALLATION..........14-20
INLET FILTER - REMOVAL..............14-20
INLET HOSE - INSTALLATION, HEATER....24-64
INLET HOSE - REMOVAL, HEATER.......24-64
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR.......................23-93
INNER BELT MOLDING - INSTALLATION,
REAR DOOR........................23-94
INNER BELT MOLDING - REMOVAL,
FRONT DOOR.......................23-93
INNER BELT MOLDING - REMOVAL,
REAR DOOR........................23-94
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-5
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-378
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-373
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-374
INPUT CLUTCH ASSEMBLY - OPERATION . 21-373
INPUT SHAFT SEAL - INSTALLATION,
STEERING GEAR.......................19-29
INPUT SHAFT SEAL - REMOVAL,
STEERING GEAR.....................19-27
INPUT SPEED SENSOR - DESCRIPTION . . 21-382
INPUT SPEED SENSOR - INSTALLATION . 21-382
INPUT SPEED SENSOR - OPERATION....21-382
INPUT SPEED SENSOR - REMOVAL.....21-382
INSERTS - INSTALLATION, SPRING TIP....2-45
INSERTS - REMOVAL, SPRING TIP........2-44
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-22,23-32
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-22,
23-31
INSTRUMENT CLUSTER - ASSEMBLY.....8J-15
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING.......................8J-10
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-14
INSTRUMENT CLUSTER - INSTALLATION . . 8J-16
INSTRUMENT CLUSTER - OPERATION.....8J-6
INSTRUMENT CLUSTER - REMOVAL.....8J-14
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-7
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-7
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-55
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-52
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-57
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-57
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-37
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-36
INSTRUMENT PANEL DRIVER SIDE
BEZEL - INSTALLATION................23-58
INSTRUMENT PANEL DRIVER SIDE
BEZEL - REMOVAL...................23-58
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - INSTALLATION.........23-56
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - REMOVAL............23-56
INSTRUMENT PANEL LOWER
SURROUND - INSTALLATION...........23-59
INSTRUMENT PANEL LOWER
SURROUND - REMOVAL
...............23-59
INSTRUMENT PANEL TOP COVER -
INSTALLATION
.......................23-59
INSTRUMENT PANEL TOP COVER -
REMOVAL
..........................23-58
INTAKE AIR HEATER - DESCRIPTION
.....14-80
INTAKE AIR HEATER - INSTALLATION
.....14-80
DRINDEX 17
Description Group-Page Description Group-Page Description Group-Page

LATCH STRIKER - INSTALLATION . . 23-17,23-23,
23-33
LATCH STRIKER - REMOVAL . 23-16,23-23,23-33
LATCH STRIKER / SECONDARY CATCH -
INSTALLATION.......................23-48
LATCH STRIKER / SECONDARY CATCH -
REMOVAL..........................23-47
LD & HD EXCEPT 4X4 HD -
INSTALLATION, ALL..................19-14
LD & HD EXCEPT 4X4 HD - REMOVAL,
ALL ...............................19-14
LD FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-7
LD FRONT - REMOVAL, PROPELLER
SHAFT...............................3-6
LEAD - DIAGNOSIS AND TESTING,
TIRE/VEHICLE........................22-8
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID....21-144,21-318
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL................9-152,9-220,9-64
LEAK DETECTION ASSY - DESCRIPTION,
NATURAL VAC.......................25-23
LEAK DETECTION ASSY - INSTALLATION,
NATURAL VAC.......................25-25
LEAK DETECTION ASSY - OPERATION,
NATURAL VAC.......................25-23
LEAK DETECTION ASSY - REMOVAL,
NATURAL VAC.......................25-24
LEAK DETECTION PUMP - DESCRIPTION . . 25-13
LEAK DETECTION PUMP - INSTALLATION . 25-16
LEAK DETECTION PUMP - OPERATION....25-14
LEAK DETECTION PUMP - REMOVAL.....25-16
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE . 9-186,9-8,
9-93
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD..............9-159,9-225
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-40
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM.........11-16
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM - TESTING.............7-5
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-58
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-72
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA...........9-137,9-209,9-65
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-44
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-1
LEAKS - STANDARD PROCEDURE,
REPAIRING.........................22-10
LEARN - STANDARD PROCEDURE,
DRIVE.............................8E-23
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-23
LEFT CYLINDER HEAD - INSTALLATION . . . 9-112
LEFT CYLINDER HEAD - REMOVAL.......9-108
LEFT REAR CABLE - INSTALLATION.......5-39
LEFT REAR CABLE - REMOVAL...........5-38
LENS REPLACEMENT - STANDARD
PROCEDURE, MODULE................8M-3
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-201,21-366
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-23
LEVEL - STANDARD PROCEDURE,
ENGINE OIL.........................9-292
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-69
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-17
LEVEL CHECK - STANDARD
PROCEDURE, FLUID...........21-202,21-366
LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING FLUID
. . . 19-43
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
..............14-57,14-6
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
..................14-7
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
................14-57,14-6
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-7LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-9
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-11
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-9
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-10
LEVER - ADJUSTMENT, SHIFT . . . 21-446,21-481
LEVER - INSTALLATION, GEAR SHIFT.....19-12
LEVER - INSTALLATION, SHIFT . . . 21-445,21-480
LEVER - REMOVAL, GEAR SHIFT........19-12
LEVER - REMOVAL, SHIFT......21-444,21-479
LEVER KNOB RELEASE - INSTALLATION,
TILT ...............................19-16
LEVER KNOB RELEASE - REMOVAL, TILT . . 19-16
LICENSE PLATE LAMP - INSTALLATION . . . 8L-17
LICENSE PLATE LAMP - REMOVAL.......8L-17
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-17
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-17
LID - INSTALLATION, CENTER SEAT
BACK..............................23-79
LID - INSTALLATION, UNDER SEAT
STORAGE BIN.......................23-80
LID - REMOVAL, CENTER SEAT BACK....23-79
LID - REMOVAL, UNDER SEAT STORAGE
BIN ...............................23-80
LIFTERS/TAPPETS - CLEANING, SOLID....9-279
LIFTERS/TAPPETS - INSPECTION, SOLID . . . 9-279
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-280
LIFTERS/TAPPETS - REMOVAL, SOLID....9-279
LIGHT DUTY FRONT FRAME RAIL TIP
REPLACEMENT - STANDARD
PROCEDURE.........................13-4
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITING VALVE - DESCRIPTION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - INSTALLATION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - OPERATION, FUEL
PRESSURE.........................14-61
LIMITING VALVE - REMOVAL, FUEL
PRESSURE.........................14-61
LINE - DESCRIPTION, A/C DISCHARGE....24-56
LINE - DESCRIPTION, LIQUID...........24-65
LINE - DESCRIPTION, REFRIGERANT.....24-42
LINE - DESCRIPTION, SUCTION.........24-70
LINE - INSTALLATION, LIQUID..........24-66
LINE - REMOVAL, LIQUID..............24-65
LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE, GRID..........8G-4
LINE COUPLER - DESCRIPTION,
REFRIGERANT.......................24-67
LINE COUPLER - INSTALLATION,
REFRIGERANT.......................24-68
LINE COUPLER - OPERATION,
REFRIGERANT.......................24-67
LINE COUPLER - REMOVAL,
REFRIGERANT.......................24-68
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-58
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-382
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-383
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-383
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-383
LINES - DESCRIPTION, FUEL.......14-57,14-7
LINES - DESCRIPTION, VACUUM........25-22
LINES - INSTALLATION, FUEL...........14-60
LINES - OPERATION, FUEL.............14-57
LINES - OPERATION, REFRIGERANT......24-42
LINES - REMOVAL, FUEL..............14-58
LINK - INSTALLATION, DRAG...........19-36
LINK - REMOVAL, DRAG...............19-36
LINK CONNECTOR - DESCRIPTION, DATA
. . 8E-3
LINK CONNECTOR - OPERATION, DATA
....8E-3
LINKAGE - INSTALLATION
...............6-12
LINKAGE - LINK/COIL - DESCRIPTION
....19-34
LINKAGE - REMOVAL
..................6-12LINKAGE, SPECIAL TOOLS - STEERING . . . 19-35
LINK/COIL - DESCRIPTION, GEAR........19-20
LINK/COIL - DESCRIPTION, LINKAGE.....19-34
LINK/COIL - INSTALLATION, GEAR.......19-21
LINK/COIL - OPERATION, GEAR.........19-20
LINK/COIL - REMOVAL, GEAR...........19-20
LINK/COIL SUSPENSION - STANDARD
PROCEDURE, ALIGNMENT...............2-5
LIQUID LINE - DESCRIPTION...........24-65
LIQUID LINE - INSTALLATION...........24-66
LIQUID LINE - REMOVAL..............24-65
LOAD FLOOR - INSTALLATION..........23-72
LOAD FLOOR - REMOVAL..............23-71
LOAD FLOOR SUPPORT CYLINDER -
INSTALLATION.......................23-72
LOAD FLOOR SUPPORT CYLINDER -
REMOVAL..........................23-72
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS - SPECIFICATIONS, SEALER . 23-102
LOCATIONS - SPECIFICATIONS,
STRUCTURAL ADHESIVE..............23-112
LOCATIONS - SPECIFICATIONS, WELD . . . 23-120
LOCK - STANDARD PROCEDURE,
HYDROSTATIC..................9-190,9-240
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY....19-11
LOCK CYLINDER - INSTALLATION.......23-24
LOCK CYLINDER - REMOVAL.............23-24
LOCK MOTOR - DESCRIPTION, DOOR.....8N-4
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-4
LOCK MOTOR - OPERATION, DOOR.......8N-4
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LOCK SWITCH - INSTALLATION, POWER . . . 8N-4
LOCK SWITCH - REMOVAL, POWER......8N-4
LOCKING RETRACTOR - DESCRIPTION,
AUTOMATIC........................8O-14
LOCKING RETRACTOR - OPERATION,
AUTOMATIC........................8O-14
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-2
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-55
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-55
LOOP BRACKETS - INSTALLATION, SEAT
BACK REAR - FOOTMANS..............23-85
LOOP BRACKETS - REMOVAL, SEAT
BACK REAR - FOOTMANS..............23-85
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-30
LOW FUEL INDICATOR - OPERATION.....8J-30
LOWER BALL JOINT - DIAGNOSIS AND
TESTING........................2-19,2-34
LOWER BALL JOINT - INSTALLATION . 2-20,2-35
LOWER BALL JOINT - REMOVAL.....2-19,2-35
LOWER CONTROL ARM BUSHINGS -
2WD (LD) - INSTALLATION..............2-15
LOWER CONTROL ARM BUSHINGS -
2WD (LD) - REMOVAL.................2-13
LOWER CONTROL ARM BUSHINGS -
4WD (LD) - INSTALLATION..............2-14
LOWER CONTROL ARM BUSHINGS -
4WD (LD) - REMOVAL.................2-13
LOWER SURROUND - INSTALLATION,
INSTRUMENT PANEL..................23-59
LOWER SURROUND - REMOVAL,
INSTRUMENT PANEL..................23-59
LOWER SUSPENSION ARM -
INSTALLATION........................2-38
LOWER SUSPENSION ARM - REMOVAL....2-38
LOWER TRIM - INSTALLATION,
B-PILLAR...........................23-64
LOWER TRIM - INSTALLATION,
C-PILLAR...........................23-67
LOWER TRIM - REMOVAL, B-PILLAR.....23-63
LOWER TRIM - REMOVAL, C-PILLAR.....23-66
LOW/REVERSE CLUTCH - ASSEMBLY....21-385
LOW/REVERSE CLUTCH - CLEANING
....21-385
LOW/REVERSE CLUTCH - DISASSEMBLY
. 21-384
LOW/REVERSE CLUTCH - INSPECTION
. . 21-385
LUBRICANTS - DESCRIPTION, ENGINE
OIL
.................................0-1
LUBRICATION - DESCRIPTION
.....9-150,9-220,
9-289,9-61
DRINDEX 19
Description Group-Page Description Group-Page Description Group-Page

MODULE - INSTALLATION, FRONT
CONTROL........................8W-97-6
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-5
MODULE - INSTALLATION, FUEL PUMP . . . 14-12
MODULE - INSTALLATION, FUEL TANK....14-64
MODULE - INSTALLATION, HANDS FREE . . . 8T-2
MODULE - INSTALLATION, HEATED SEAT . . . 8E-7
MODULE - INSTALLATION, HEATED SEAT . 8G-15
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-4
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY......................8N-8
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-15
MODULE - INSTALLATION, WIPER.......8R-23
MODULE - OPERATION, AIRBAG
CONTROL..........................8O-11
MODULE - OPERATION, DRIVER DOOR....8N-5
MODULE - OPERATION, FRONT
CONTROL........................8W-97-5
MODULE - OPERATION, FRONT
CONTROL...........................8E-5
MODULE - OPERATION, FUEL PUMP.....14-11
MODULE - OPERATION, FUEL TANK......14-63
MODULE - OPERATION, HEATED SEAT.....8E-6
MODULE - OPERATION, HEATED SEAT....8G-14
MODULE - OPERATION, INTEGRATED
POWER..........................8W-97-3
MODULE - OPERATION, REMOTE
KEYLESS ENTRY......................8N-7
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER.......................8E-13
MODULE - OPERATION, TRANSFER CASE
CONTROL..........................8E-16
MODULE - OPERATION, TRANSMISSION
CONTROL..........................8E-20
MODULE - OPERATION, WIPER.........8R-23
MODULE - REMOVAL, AIRBAG CONTROL . 8O-12
MODULE - REMOVAL, DRIVER DOOR.....8N-7
MODULE - REMOVAL, ENGINE CONTROL . . . 8E-4
MODULE - REMOVAL, FRONT CONTROL . 8W-97-6
MODULE - REMOVAL, FRONT CONTROL . . . 8E-5
MODULE - REMOVAL, FUEL PUMP.......14-12
MODULE - REMOVAL, FUEL TANK.......14-63
MODULE - REMOVAL, HANDS FREE.......8T-2
MODULE - REMOVAL, HEATED SEAT......8E-7
MODULE - REMOVAL, HEATED SEAT.....8G-15
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-3
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY..............................8N-7
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER.......................8E-15
MODULE - REMOVAL, WIPER...........8R-23
MODULE / SWITCH OPERATING MODES,
STANDARD PROCEDURE -
CONFIGURING A NEW.................8Q-3
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE...............8M-3
MODULE LENS REPLACEMENT -
STANDARD PROCEDURE...............8M-3
MODULE (SKIM) - DESCRIPTION,
SENTRY KEY IMMOBILIZER.............8Q-1
MODULE (SKIM) - OPERATION, SENTRY
KEY IMMOBILIZER
....................8Q-2
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT
...................23-93
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT
...................23-93
MOLDING - INSTALLATION, REAR DOOR
INNER BELT
.........................23-94
MOLDING - INSTALLATION, REAR DOOR
OUTER BELT
........................23-94
MOLDING - REMOVAL, FRONT DOOR
INNER BELT
.........................23-93
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT
........................23-92
MOLDING - REMOVAL, REAR DOOR
INNER BELT
.........................23-94
MOLDING - REMOVAL, REAR DOOR
OUTER BELT
........................23-93
MOLDINGS - INSTALLATION, BODY SIDE
. . 23-36
MOLDINGS - REMOVAL, BODY SIDE
.....23-36
MONITORED SYSTEMS - DESCRIPTION
....25-2
MONITORS - DESCRIPTION,
COMPONENT
.........................25-4MOTOR - DESCRIPTION, ADJUSTABLE
PEDAL...............................5-6
MOTOR - DESCRIPTION, BLOWER.......24-28
MOTOR - DESCRIPTION, DOOR LOCK.....8N-4
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-28
MOTOR - DESCRIPTION, LUMBAR.......8N-18
MOTOR - DESCRIPTION, SHIFT . . 21-511,21-541,
21-575
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-28
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK.........................8N-4
MOTOR - DIAGNOSIS AND TESTING,
LUMBAR...........................8N-18
MOTOR - DIAGNOSIS AND TESTING,
STARTER ...........................8F-32
MOTOR - INSTALLATION, ADJUSTABLE
PEDAL...............................5-7
MOTOR - INSTALLATION, BLOWER......24-31
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-29
MOTOR - INSTALLATION, SHIFT . 21-511,21-541,
21-575
MOTOR - INSTALLATION, STARTER......8F-34
MOTOR - OPERATION, BLOWER.........24-28
MOTOR - OPERATION, DOOR LOCK.......8N-4
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-28
MOTOR - OPERATION, LUMBAR........8N-18
MOTOR - OPERATION, SHIFT.....21-511,21-541,
21-575
MOTOR - REMOVAL, ADJUSTABLE
PEDAL...............................5-7
MOTOR - REMOVAL, BLOWER..........24-31
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-29
MOTOR - REMOVAL, SHIFT.....21-511,21-541,
21-575
MOTOR - REMOVAL, STARTER..........8F-33
MOTOR - REMOVAL, WINDOW..........8N-20
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-35
MOTOR RELAY - INSTALLATION,
STARTER ...........................8F-37
MOTOR RELAY - OPERATION, STARTER . . . 8F-36
MOTOR RELAY - REMOVAL, STARTER....8F-37
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-18
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, BLOWER...............24-19
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER..............24-19
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER...........................24-18
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER...........................24-19
MOTOR SWITCH - DESCRIPTION,
BLOWER...........................24-20
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER...................24-20
MOTOR SWITCH - OPERATION, BLOWER . . 24-20
MOUNT - INSTALLATION, DISC BRAKE
CALIPER ADAPTER....................5-22
MOUNT - INSTALLATION, FRONT . . . 9-147,9-218,
9-287,9-59
MOUNT - INSTALLATION, REAR
....9-149,9-220,
9-288,9-61
MOUNT - REMOVAL, FRONT
. 9-146,9-217,9-286,
9-58
MOUNT - REMOVAL, REAR
. . 9-149,9-220,9-288,
9-61
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH
.......................8L-11
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH
.......................8L-11
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH
..........8L-11
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH
..............8L-11
MOUNTING - STANDARD PROCEDURE,
MATCH
.............................22-3
MUFFLER - 5.9L DIESEL - INSTALLATION
. 11-10
MUFFLER - 5.9L DIESEL - REMOVAL
.....11-10
MUFFLER - INSTALLATION
..............11-9
MUFFLER - REMOVAL
..................11-9
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING
.......................8L-18MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-19
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-19
NAME PLATES - INSTALLATION,
EXTERIOR..........................23-38
NAME PLATES - REMOVAL, EXTERIOR....23-38
NATURAL VAC LEAK DETECTION ASSY -
DESCRIPTION.......................25-23
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-25
NATURAL VAC LEAK DETECTION ASSY -
OPERATION.........................25-23
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-24
NAVIGATION - INSTALLATION, ANTENNA . . . 8A-6
NAVIGATION - REMOVAL, ANTENNA......8A-6
NAVIGATION/TELECOMMUNICATION -
DESCRIPTION........................8T-1
NAVIGATION/TELECOMMUNICATION -
OPERATION..........................8T-1
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER..............7-58
NEW MODULE / SWITCH OPERATING
MODES, STANDARD PROCEDURE -
CONFIGURING A......................8Q-3
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-11
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-11
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-11
NIGHT MIRROR - REMOVAL,
AUTOMATIC DAY......................8N-12
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-7
NOISE SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO..................8A-9
NOISE SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO................8A-10
NOISE SUPPRESSION GROUND STRAP -
OPERATION, RADIO...................8A-9
NOISE SUPPRESSION GROUND STRAP -
REMOVAL, RADIO.....................8A-9
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NON-MONITORED CIRCUITS -
OPERATION..........................25-8
NOZZLE - DESCRIPTION, WASHER......8R-11
NOZZLE - INSTALLATION, WASHER......8R-12
NOZZLE - OPERATION, WASHER........8R-12
NOZZLE - REMOVAL, WASHER..........8R-12
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-1
NV241 GENII - ASSEMBLY, TRANSFER
CASE.............................21-428
NV241 GENII - CLEANING, TRANSFER
CASE.............................21-426
NV241 GENII - DESCRIPTION, TRANSFER
CASE.............................21-415
NV241 GENII - DIAGNOSIS AND
TESTING, TRANSFER CASE............21-416
NV241 GENII - DISASSEMBLY,
TRANSFER CASE....................21-417
NV241 GENII - INSPECTION, TRANSFER
CASE.............................21-426
NV241 GENII - INSTALLATION,
TRANSFER CASE....................21-438
NV241 GENII - OPERATION, TRANSFER
CASE.............................21-415
NV241 GENII - REMOVAL, TRANSFER
CASE.............................21-417
NV241 GENII - TRANSFER CASE........21-438
NV241/NV243 - TRANSFER CASE.......21-439
NV243 - ASSEMBLY, TRANSFER CASE . . . 21-496
NV243 - CLEANING, TRANSFER CASE . . . 21-493
NV243 - DESCRIPTION, TRANSFER CASE . 21-482
NV243 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-483
NV243 - DISASSEMBLY, TRANSFER
CASE
.............................21-484
NV243 - INSPECTION, TRANSFER CASE
. . 21-493
NV243 - INSTALLATION, TRANSFER
CASE
.............................21-505
NV243 - OPERATION, TRANSFER CASE
. . 21-483
NV243 - REMOVAL, TRANSFER CASE
....21-484
DRINDEX 21
Description Group-Page Description Group-Page Description Group-Page

PRESSURE HOSE - REMOVAL.....19-44,19-45
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION . . . 9-186,9-8,
9-93
PRESSURE LIMITING VALVE -
DESCRIPTION, FUEL..................14-61
PRESSURE LIMITING VALVE -
INSTALLATION, FUEL.................14-61
PRESSURE LIMITING VALVE -
OPERATION, FUEL....................14-61
PRESSURE LIMITING VALVE - REMOVAL,
FUEL..............................14-61
PRESSURE (LP) SENSOR -
DESCRIPTION, LINE.................21-382
PRESSURE (LP) SENSOR -
INSTALLATION, LINE.................21-383
PRESSURE (LP) SENSOR - OPERATION,
LINE..............................21-383
PRESSURE (LP) SENSOR - REMOVAL,
LINE..............................21-383
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-2
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-294
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-48
PRESSURE RELIEF VALVE - INSPECTION,
OIL................................9-294
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-294
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-48
PRESSURE RELIEF VALVE - REMOVAL,
OIL.................................9-294
PRESSURE SENSOR - DESCRIPTION,
FUEL..............................14-60
PRESSURE SENSOR - INSTALLATION,
FUEL..............................14-61
PRESSURE SENSOR - OPERATION, FUEL . . 14-60
PRESSURE SENSOR - REMOVAL, FUEL . . . 14-60
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-67
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL....................9-67
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-67
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL.......................9-67
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-3
PRESSURE SWITCH - DESCRIPTION,
POWER STEERING...................19-46
PRESSURE SWITCH - INSTALLATION,
OIL................................9-294
PRESSURE SWITCH - OPERATION,
POWER STEERING...................19-46
PRESSURE SWITCH - REMOVAL, OIL.....9-294
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC..........21-141,21-316
PRESSURE TRANSDUCER -
DESCRIPTION, A/C
...................24-15
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C
...................24-16
PRESSURE TRANSDUCER -
INSTALLATION, A/C
...................24-16
PRESSURE TRANSDUCER - OPERATION,
A/C
................................24-16
PRESSURE TRANSDUCER - REMOVAL,
A/C
................................24-16
PRESSURES - DESCRIPTION, TIRE
INFLATION
...........................22-7
PRIMING - STANDARD PROCEDURE,
FUEL SYSTEM
.......................14-47
PROCESS - SPECIFICATIONS, WELD
.....13-15
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER
........8N-9
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER
................8M-8
PROGRAMMING - STANDARD
PROCEDURE, ENHANCED SEATBELT
REMINDER
..........................8J-35
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM
...............8E-14
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY
IMMOBILIZER SYSTEM TRANSPONDER
....8Q-4PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - HD FRONT -
INSTALLATION.........................3-7
PROPELLER SHAFT - HD FRONT -
REMOVAL............................3-7
PROPELLER SHAFT - INSTALLATION,
REAR................................3-8
PROPELLER SHAFT - REMOVAL, REAR.....3-8
PROPELLER SHAFT - SPECIAL TOOLS......3-6
PROPELLER SHAFT - SPECIFICATIONS......3-6
PROPELLER SHAFT - STANDARD
PROCEDURE..........................3-3
PROPELLER SHAFT- LD FRONT -
INSTALLATION.........................3-7
PROPELLER SHAFT- LD FRONT -
REMOVAL............................3-6
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE..........5-49
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-49
PTO SWITCH - DESCRIPTION......14-36,14-85
PTO SWITCH - OPERATION........14-36,14-85
PULLEY - INSTALLATION..............19-47
PULLEY - REMOVAL..................19-47
PUMP - 5.7L - INSTALLATION, WATER.....7-63
PUMP - 5.7L - REMOVAL, WATER........7-63
PUMP - 5.9L DIESEL - CLEANING,
WATER .............................7-62
PUMP - 5.9L DIESEL - DESCRIPTION,
WATER...............................7-62
PUMP - 5.9L DIESEL - INSPECTION,
WATER .............................7-62
PUMP - 5.9L DIESEL - INSTALLATION,
WATER .............................7-62
PUMP - 5.9L DIESEL - OPERATION,
WATER .............................7-62
PUMP - 5.9L DIESEL - REMOVAL,
WATER .............................7-62
PUMP - 8.0L - CLEANING, WATER........7-66
PUMP - 8.0L - INSPECTION, WATER......7-66
PUMP - 8.0L - INSTALLATION, WATER.....7-66
PUMP - 8.0L - REMOVAL, WATER........7-64
PUMP - ASSEMBLY, OIL...........9-158,9-69
PUMP - ASSEMBLY, OIL........21-214,21-390
PUMP - CLEANING, OIL.....9-157,9-224,9-295
PUMP - CLEANING, OIL........21-214,21-390
PUMP - DESCRIPTION................19-39
PUMP - DESCRIPTION, FUEL...........14-11
PUMP - DESCRIPTION, FUEL INJECTION . . 14-53
PUMP - DESCRIPTION, FUEL TRANSFER . . 14-64
PUMP - DESCRIPTION, LEAK DETECTION . 25-13
PUMP - DESCRIPTION, OIL......21-213,21-386
PUMP - DESCRIPTION, WATER..........7-59
PUMP - DIAGNOSIS AND TESTING,
WATER .........................7-62,7-63
PUMP - DISASSEMBLY, OIL........9-157,9-68
PUMP - DISASSEMBLY, OIL.....21-214,21-388
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-40
PUMP - INSPECTION, OIL . . . 9-157,9-224,9-295,
9-68
PUMP - INSPECTION, OIL.......21-214,21-390
PUMP - INSTALLATION, FUEL INJECTION . 14-55
PUMP - INSTALLATION, FUEL TRANSFER . 14-65
PUMP - INSTALLATION, LEAK
DETECTION.........................25-16
PUMP - INSTALLATION, OIL . 9-159,9-225,9-296,
9-69
PUMP - OPERATION..................19-40
PUMP - OPERATION, FUEL.............14-11
PUMP - OPERATION, FUEL INJECTION....14-53
PUMP - OPERATION, FUEL TRANSFER....14-64
PUMP - OPERATION, LEAK DETECTION . . . 25-14
PUMP - OPERATION, OIL.......21-213,21-386
PUMP - OPERATION, WATER............7-60
PUMP - REMOVAL, FUEL INJECTION.....14-54
PUMP - REMOVAL, FUEL TRANSFER.....14-64
PUMP - REMOVAL, LEAK DETECTION....25-16
PUMP - REMOVAL, OIL . 9-156,9-224,9-294,9-67
PUMP BYPASS - DESCRIPTION, WATER
. . . 7-59
PUMP BYPASS - OPERATION, WATER
.....7-60
PUMP FRONT SEAL - INSTALLATION,
OIL
...............................21-391
PUMP FRONT SEAL - REMOVAL, OIL
....21-391
PUMP LEAKAGE - DIAGNOSIS AND
TESTING
...........................19-40PUMP MODULE - DESCRIPTION, FUEL....14-11
PUMP MODULE - INSTALLATION, FUEL . . . 14-12
PUMP MODULE - OPERATION, FUEL.....14-11
PUMP MODULE - REMOVAL, FUEL.......14-12
PUMP RELAY - DESCRIPTION, FUEL.....14-27
PUMP RELAY - INSTALLATION, FUEL.....14-28
PUMP RELAY - OPERATION, FUEL.......14-27
PUMP RELAY - REMOVAL, FUEL........14-28
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL...............8I-5
PUMP TIMING - DIAGNOSIS AND
TESTING, FUEL INJECTION.............14-53
PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-387
PUMP/MOTOR - DESCRIPTION, WASHER . 8R-13
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-14
PUMP/MOTOR - OPERATION, WASHER . . . 8R-13
PUMP/MOTOR - REMOVAL, WASHER....8R-14
PUSHRODS - CLEANING...............9-252
PUSHRODS - INSPECTION.............9-253
QUAD CAB - INSTALLATION.......8O-36,8O-61
QUAD CAB - REMOVAL..........8O-33,8O-60
QUICK CONNECT FITTING -
DESCRIPTION........................14-8
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-23
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE...........................14-8
RADIAL - PLY TIRES - DESCRIPTION......22-6
RADIATOR - 5.9L DIESEL - CLEANING.....7-56
RADIATOR - 5.9L DIESEL -
DESCRIPTION........................7-56
RADIATOR - 5.9L DIESEL - INSPECTION . . . 7-56
RADIATOR - 5.9L DIESEL -
INSTALLATION........................7-57
RADIATOR - 5.9L DIESEL - OPERATION....7-56
RADIATOR - 5.9L DIESEL - REMOVAL.....7-56
RADIATOR CAP - DIAGNOSIS AND
TESTING............................7-58
RADIATOR CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING..............7-58
RADIATOR COOLANT FLOW -
DIAGNOSIS AND TESTING..........7-54,7-56
RADIATOR CROSSMEMBER -
INSTALLATION, UPPER................23-42
RADIATOR CROSSMEMBER - REMOVAL,
UPPER.............................23-42
RADIATOR FAN - 5.9L DIESEL -
CLEANING...........................7-35
RADIATOR FAN - 5.9L DIESEL -
INSPECTION.........................7-35
RADIATOR FAN - 5.9L DIESEL -
INSTALLATION........................7-36
RADIATOR FAN - 5.9L DIESEL -
REMOVAL...........................7-35
RADIATOR FAN - GAS ENGINES -
CLEANING...........................7-34
RADIATOR FAN - GAS ENGINES -
INSPECTION.........................7-34
RADIATOR FAN - GAS ENGINES -
INSTALLATION........................7-34
RADIATOR FAN - GAS ENGINES -
REMOVAL...........................7-33
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-57
RADIATOR PRESSURE CAP - OPERATION . . 7-58
RADIATOR-3.7L/4.7L/5.7L - CLEANING.....7-55
RADIATOR-3.7L/4.7L/5.7L -
DESCRIPTION........................7-54
RADIATOR-3.7L/4.7L/5.7L - INSPECTION . . . 7-55
RADIATOR-3.7L/4.7L/5.7L -
INSTALLATION........................7-55
RADIATOR-3.7L/4.7L/5.7L - OPERATION....7-54
RADIATOR-3.7L/4.7L/5.7L - REMOVAL.....7-54
RADIO - DESCRIPTION.................8A-8
RADIO - INSTALLATION................8A-8
RADIO - OPERATION...................8A-8
RADIO - REMOVAL....................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION
.................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION
...............8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION
..................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL
....................8A-9
RAIL - DESCRIPTION, FUEL
............14-12
DRINDEX 25
Description Group-Page Description Group-Page Description Group-Page

RELAY - DESCRIPTION, STARTER
MOTOR............................8F-35
RELAY - DESCRIPTION, TRANSMISSION
CONTROL.........................21-405
RELAY - DESCRIPTION, WIPER
HIGH/LOW..........................8R-20
RELAY - DESCRIPTION, WIPER ON/OFF . . . 8R-24
RELAY - DIAGNOSIS AND TESTING,
PARK LAMP.........................8L-20
RELAY - DIAGNOSIS AND TESTING,
STARTER ...........................8F-36
RELAY - DIAGNOSIS AND TESTING,
WIPER HIGH/LOW...................8R-21
RELAY - DIAGNOSIS AND TESTING,
WIPER ON/OFF......................8R-25
RELAY - INSTALLATION, A/C
COMPRESSOR CLUTCH...............24-14
RELAY - INSTALLATION, FOG LAMP......8L-13
RELAY - INSTALLATION, FUEL HEATER . . . 14-53
RELAY - INSTALLATION, FUEL PUMP.....14-28
RELAY - INSTALLATION, INTAKE AIR
HEATER ............................14-82
RELAY - INSTALLATION, PARK LAMP.....8L-21
RELAY - INSTALLATION, REAR WINDOW
DEFOGGER..........................8G-4
RELAY - INSTALLATION, STARTER
MOTOR............................8F-37
RELAY - INSTALLATION, WIPER
HIGH/LOW..........................8R-22
RELAY - INSTALLATION, WIPER ON/OFF . . 8R-26
RELAY - OPERATION, A/C COMPRESSOR
CLUTCH.............................24-13
RELAY - OPERATION, FOG LAMP........8L-13
RELAY - OPERATION, FUEL HEATER......14-52
RELAY - OPERATION, FUEL PUMP.......14-27
RELAY - OPERATION, INTAKE AIR
HEATER ............................14-82
RELAY - OPERATION, PARK LAMP.......8L-20
RELAY - OPERATION, REAR WINDOW
DEFOGGER..........................8G-3
RELAY - OPERATION, STARTER MOTOR . . . 8F-36
RELAY - OPERATION, TRANSMISSION
CONTROL.........................21-405
RELAY - OPERATION, WIPER HIGH/LOW . . 8R-20
RELAY - OPERATION, WIPER ON/OFF....8R-25
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-14
RELAY - REMOVAL, FOG LAMP.........8L-13
RELAY - REMOVAL, FUEL HEATER.......14-52
RELAY - REMOVAL, FUEL PUMP........14-28
RELAY - REMOVAL, INTAKE AIR HEATER . . 14-82
RELAY - REMOVAL, PARK LAMP........8L-21
RELAY - REMOVAL, REAR WINDOW
DEFOGGER..........................8G-3
RELAY - REMOVAL, STARTER MOTOR....8F-37
RELAY - REMOVAL, WIPER HIGH/LOW . . . 8R-21
RELAY - REMOVAL, WIPER ON/OFF......8R-26
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-5
RELEASE - INSTALLATION, TILT LEVER
KNOB..............................19-16
RELEASE - REMOVAL, TILT LEVER KNOB . . 19-16
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-2
RELEASE BEARING - INSTALLATION,
CLUTCH
.............................6-10
RELEASE BEARING - REMOVAL, CLUTCH
...6-9
RELEASE CABLE/HANDLE ASSEMBLY -
INSTALLATION, LATCH
................23-47
RELEASE CABLE/HANDLE ASSEMBLY -
REMOVAL, LATCH
....................23-47
RELEASE HANDLE - INSTALLATION
.......5-44
RELEASE HANDLE - REMOVAL
...........5-44
RELEASE HANDLE/LATCH REMOTE -
INSTALLATION
.......................23-17
RELEASE HANDLE/LATCH REMOTE -
REMOVAL
..........................23-17
RELIEF VALVE - CLEANING, OIL
PRESSURE
.........................9-294
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE
.........................24-48
RELIEF VALVE - INSPECTION, OIL
PRESSURE
.........................9-294
RELIEF VALVE - INSTALLATION, OIL
PRESSURE
.........................9-294
RELIEF VALVE - OPERATION, HIGH
PRESSURE
.........................24-48RELIEF VALVE - REMOVAL, OIL
PRESSURE.........................9-294
REMINDER PROGRAMMING -
STANDARD PROCEDURE, ENHANCED
SEATBELT..........................8J-35
REMOTE - INSTALLATION, RELEASE
HANDLE/LATCH......................23-17
REMOTE - REMOVAL, RELEASE
HANDLE/LATCH......................23-17
REMOTE KEYLESS ENTRY MODULE -
DESCRIPTION........................8N-7
REMOTE KEYLESS ENTRY MODULE -
DIAGNOSIS AND TESTING..............8N-7
REMOTE KEYLESS ENTRY MODULE -
INSTALLATION.......................8N-8
REMOTE KEYLESS ENTRY MODULE -
OPERATION..........................8N-7
REMOTE KEYLESS ENTRY MODULE -
REMOVAL...........................8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-8
REMOTE KEYLESS ENTRY
TRANSMITTER - SPECIFICATIONS........8N-9
REMOTE SWITCHES - DESCRIPTION.....8A-10
REMOTE SWITCHES - DIAGNOSIS AND
TESTING...........................8A-11
REMOTE SWITCHES - INSTALLATION.....8A-12
REMOTE SWITCHES - OPERATION.......8A-11
REMOTE SWITCHES - REMOVAL........8A-12
REMOVAL/INSTALLATION, REMOVAL.....25-13
REMOVAL/INSTALLATION, REMOVAL.....14-52,
14-57,14-66
REPAIR - DESCRIPTION, THREADED
HOLE.............................Intro.-8
REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD...........21-158,21-318
REPAIR - STANDARD PROCEDURE, CAM
BORE..............................9-267
REPAIR - STANDARD PROCEDURE,
CYLINDER BORE.....................9-265
REPAIR - STANDARD PROCEDURE, GRID
LINE AND TERMINAL..................8G-4
REPAIR - STANDARD PROCEDURE,
HYDROFORM FENDER RAIL............13-11
REPAIR - STANDARD PROCEDURE,
PLASTIC BODY PANEL.................23-3
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE . 9-190,9-240,9-9,9-94
REPAIRING LEAKS - STANDARD
PROCEDURE........................22-10
REQUIREMENTS - DESCRIPTION,
ENGINE COOLING SYSTEM..............24-1
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-1
RESERVOIR - DESCRIPTION, VACUUM....8P-9
RESERVOIR - DESCRIPTION, WASHER . . . 8R-14
RESERVOIR - DIAGNOSIS AND TESTING,
VACUUM............................8P-9
RESERVOIR - INSTALLATION...........19-47
RESERVOIR - INSTALLATION, FLUID......5-24
RESERVOIR - INSTALLATION, VACUUM . . . 8P-10
RESERVOIR - OPERATION, VACUUM......8P-9
RESERVOIR - OPERATION, WASHER.....8R-15
RESERVOIR - REMOVAL...............19-47
RESERVOIR - REMOVAL, FLUID..........5-23
RESERVOIR - REMOVAL, VACUUM........8P-9
RESERVOIR TO COOLER -
INSTALLATION, RETURN HOSE.....19-44,19-45
RESERVOIR TO COOLER - REMOVAL,
RETURN HOSE.................19-44,19-45
RESISTANCE, 3.7L V-6 - IGNITION COIL....8I-5
RESISTANCE, 4.7L V-8 - IGNITION COIL....8I-5
RESISTANCE, 5.7L V-8 - IGNITION COIL....8I-5
RESISTANCE, SPECIFICATIONS - SPARK
PLUG CABLE.........................8I-4
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR....................24-18
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR
............24-19
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR
....................24-19
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR
....................24-18
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR
............................24-19
RESTRAINT ANCHOR - DESCRIPTION,
CHILD
.............................8O-15RESTRAINT ANCHOR - INSTALLATION,
CHILD.............................8O-18
RESTRAINT ANCHOR - OPERATION,
CHILD.............................8O-17
RESTRAINT ANCHOR - REMOVAL, CHILD . 8O-17
RESTRAINT DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL......................8O-7
RESTRAINT SYSTEM - DIAGNOSIS AND
TESTING, SUPPLEMENTAL..............8O-6
RESTRAINT SYSTEM - WARNINGS.......8O-5
RESTRAINTS - DESCRIPTION............8O-2
RESTRAINTS - OPERATION.............8O-4
RESTRAINTS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED
SUPPLEMENTAL......................8O-6
RETAINER - ASSEMBLY, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON......21-237
RETAINER - CLEANING, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON......21-236
RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON.................21-236
RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON.................21-236
RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON.................21-237
RETAINER - INSTALLATION, A-PILLAR
WEATHERSTRIP.....................23-91
RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL SEAL.....9-210,9-277
RETAINER - INSTALLATION, DRIP RAIL
WEATHERSTRIP.....................23-92
RETAINER - OPERATION, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON......21-236
RETAINER - REMOVAL, A-PILLAR
WEATHERSTRIP.....................23-91
RETAINER - REMOVAL, CRANKSHAFT
REAR OIL SEAL.................9-209,9-277
RETAINER - REMOVAL, DRIP RAIL
WEATHERSTRIP.....................23-92
RETAINER/BULKHEAD - ASSEMBLY, 4C . . 21-363
RETAINER/BULKHEAD - DISASSEMBLY,
4C ...............................21-362
RETRACTOR - DESCRIPTION,
AUTOMATIC LOCKING.................8O-14
RETRACTOR - INSTALLATION, FRONT
CENTER SEAT BELT..................8O-29
RETRACTOR - INSTALLATION, REAR
CENTER SEAT BELT..................8O-45
RETRACTOR - INSTALLATION, REAR
OUTBOARD SEAT BELT................8O-47
RETRACTOR - OPERATION, AUTOMATIC
LOCKING...........................8O-14
RETRACTOR - REMOVAL, FRONT
CENTER SEAT BELT..................8O-29
RETRACTOR - REMOVAL, REAR CENTER
SEAT BELT .........................8O-44
RETRACTOR - REMOVAL, REAR
OUTBOARD SEAT BELT................8O-46
RETURN - DESCRIPTION, SENSOR.......8E-10
RETURN HOSE - GEAR TO COOLER -
INSTALLATION..................19-44,19-45
RETURN HOSE - GEAR TO COOLER -
REMOVAL.....................19-44,19-45
RETURN HOSE - INSTALLATION, HEATER . 24-65
RETURN HOSE - REMOVAL, HEATER.....24-64
RETURN HOSE - RESERVOIR TO
COOLER - INSTALLATION.........19-44,19-45
RETURN HOSE - RESERVOIR TO
COOLER - REMOVAL.............19-44,19-45
REVOLUTIONS PER MILE,
SPECIFICATIONS - TIRE...............22-10
RFE TRANSMISSION, SPECIAL TOOLS . . . 21-359
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE.....3-108,3-137,3-164
RING - REMOVAL, PINION GEAR/RING
GEAR/TONE...............3-106,3-134,3-162
RING FITTING - STANDARD
PROCEDURE, PISTON . . . 9-142,9-213,9-284,9-53
RINGS - ASSEMBLY, WITH INJECTED
......3-13
RINGS - ASSEMBLY, WITH SNAP
.........3-12
RINGS - DISASSEMBLY, WITH INJECTED
. . . 3-11
RINGS - DISASSEMBLY, WITH SNAP
......3-10
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE
...............8N-8
DRINDEX 27
Description Group-Page Description Group-Page Description Group-Page