1998 CHEVROLET S10 Owners Manual

With :the wmnL i? flu-id. in -your brake.
sptem, your brakes may not work well, or they
aa.y ,not even wotk at all. This :ciuld cause 8
crash. Always-use-the .. proper brake fluid..
NOTICE:
ProCarManuals.com

The L-ke wc,: warnin, sound means tht-so.on
your- brakes wanit wa.s.k.we11. That..could 1egd.to
an accident. When you hear the brake wear
warningsound, .. have, yo.w vehicle serviced,
.
NOTICE:.
ProCarManuals.com

f
Brake Adj.ustmc c
Vehicle.. Storage.
If you’re not goifigjto drive ...y.o ur vehkle fGr.25 days m
more, r~move the black, negative (-.$ cable fram
the battery. this will .heip keep yrrzrrbattery from
rmning dowiz-.
-
Batteries have acid that can burn yg~ nd I&
that can explode. You caa be- b.adly hurt-if .you
aren’t careful,. S.ee ‘-‘Jump ‘Sbrting’? in th&dex-
for tips on working around a battery without
getting hurt.
6-34
ProCarManuals.com

Bulb Replacement
Befre.you replace any bulbs., be sure that- all the 1.mps
axe offand; &e-engine isn’t running. See- “Replacement
B-ulbs” .in .,&e- Index..
F.or my bulb changing procedure not listed -in zhis
section, contact your GM dealer% service dep,artment.
Halagen Bulbs
I
..Headlamps.
OnemPiece Comp.osi’te .Headlamp System
i. Open the ho.od.
.1
6-35
ProCarManuals.com

:5 0
.6.,
7.
:8 .
I
Turn the bulb assembly to the. left to-remove it.
Put
the ne-w bulb assembly into the headlamp
assembly
and turn it to the right until it is tight.
Plug in the electrical connector.
Put the headlamp lens assembly back into the
vehicle, Install the ~WO ,retaining. clips.
Two-Piece. Composite Headlamp System
1. Open the h.ood.
2. Remove the black retainer clips- by lifting up.
3. Pull the headlamp lens .assembly out.
4. Uop1ug:the ekctrical connectox.
6-36
f
ProCarManuals.com

One-Piece Front 7h-n Signal Lamp Assembly
1. Remove the headlamp assembly .as shown. under
“One-Piece Composite Headlamp System” earlier
in
this section.
5. Turn the bulb assembly to.the left to remove it.
6. Put the new bulb assembly into the headlamp
assembly
and turn it to the right until it is tight.
7. Plug in the dectrical connector.
8. Put. the headlamp lens assembly back into the
vehicle. Install the two retaining clips.
2. Twist the bulb socket to-
remove it from the
headlamp assembly.
3. Pull the bulb straight out to remove it from
4. Push the new bulb into-the socket until it snaps
the socket.
into place.
5. Put the bulb socket-into the lamp assembly arid twist
it to the right until it is tight.
6. Put the headlamp assembly back into the vehicle.
Install the twwetainhg clips.
ProCarManuals.com

1. Remove the headlamp assembly as-shown under
“Two-Pie-ce Composite Headlamp System” ,earlier in
this section,
2. Lacate the locking tabs
-on the assembly.
Squeeze the
tabs
together and push.that
end
of the-assembly out
while
holding the tabs.
-The assembly will
.swing .out.
3. Unplug the electrical conne-czw. 6.
7.
6-38
4.
5.
Turn the harness bulb socket to the left to remove it.
Push the new b.ulb into the socket until it. snaps
into place.
Put the new bulb
into the headlamp. lens- assembly
and turn it to the right until it is. tight.
To replace the .assembly, snap the outboard end of
the lamp assembly back into the vehicle. Then swing
the assembly in ,and snap it into place.
ProCarManuals.com

1. Remove the 1ens:retaining screws.
2. Remove the lens..
:3 ’ Remove the bulb..
ProCarManuals.com