1998 CHEVROLET BLAZER width

Downloaded from www.Manualslib.com manuals search engine What's wrong with this?
You can be seriously injured by a twisted belt. In
a crash, you wouldn't have the full width of the
belt to spread impact forces. If a belt is twisted,
make it straight
so it can work properly, or ask
your dealer to fix it.
A: The belt is twisted across the body.
1-21

Downloaded from www.Manualslib.com manuals search engine @ Am I likely to stall when going downhill?
A: It’s much more likely to happen going uphill. But if
it happens going downhill, here’s what to do.
0
a
a
0
Stop your vehicle by applying the regular brakes.
Apply the parking brake.
Shift to
PARK (P) (or to NEUTRAL (N) with the
manual transmission) and, while still braking, restart
the engine.
Shift back to
a low gear, release the parking brake,
and drive straight down.
If the engine won’t start, get out and get help.
Driving Across an Incline
Sooner or later, an off-road trail will probably go across
the incline
of a hill. If this happens, you have to decide
whether
to try to drive across the incline. Here are some
things to consider:
0 A hill that can be driven straight up or down may be
too steep to drive across. When you
go straight up or
down a hill, the length
of the wheel base (the distance
from the front wheels to the rear wheels) reduces the
likelihood the
vehicle will tumble end over end. But
when
you drive across an incline, the much more
narrow track width
(the distance between the left and
right wheels) may not prevent the vehicle
from tilting
and rolling over.
Also, driving across an incline puts
more weight on the dowhll wheels.
This could cause
a downhill slide or a rollover.
0 Surface conditions can be a problem when you drive
across a hill. Loose gravel, muddy spots, or even wet
grass can cause your tires to slip sideways, downhill.
If the vehicle slips sideways, it can hit something
that will trip it (a rock, a rut, etc.) and roll over.
Hidden obstacles can make the steepness of the
incline even worse.
If you drive across a rock with
the uphill wheels, or if the downhill wheels
drop into
a rut or depression, your vehicle can tilt even more.
For reasons like these, you need
to decide carefully
whether to try to drive across an incline. Just because
the trail goes across the incline doesn’t mean
you have
to drive it. The last vehicle
to try it might have
rolled over.
4-23

Downloaded from www.Manualslib.com manuals search engine Wheel Alignment and Tire Balance
The wheels on your vehicle were aligned and balanced
carefully at the factory to give you the longest tire life
and best overall performance.
Scheduled wheel alignment and wheel balancing are
not needed. However, if you notice unusual tire wear
or your vehicle pulling one way or the other, the
alignment may need to be reset. If you notice your
vehicle vibrating when driving on a smooth road,
your wheels may need to
be rebalanced.
Wheel Replacement
Replace any wheel that is bent, cracked, or badly rusted
or corroded. If wheel nuts keep coming loose, the wheel,
wheel bolts and wheel nuts should be replaced. If the
wheel leaks air, replace it (except some aluminum
wheels, which can sometimes be repaired). See your
dealer if any
of these conditions exist.
Your dealer will know the kind of wheel
you need. Each new wheel should have the
same load-carrying
capacity, diameter, width, offset and be mounted the same way as the one it replaces.
If
you need to replace any of your wheels, wheel
bolts or wheel nuts, replace them only with new
GM
original equipment parts. This way, you will be sure to
have the right wheel, wheel bolts and wheel nuts for
your
GM model.
Using the wrong replacement wheels, wheel
bolts or wheel nuts on your vehicle can be
dangerous. It could affect the braking and
handling
of your vehicle, make your tires lose
air and make you lose control. You could have a
collision in which you or others could be injured.
Always use the correct wheel, wheel bolts and
wheel nuts for replacement.
6-47

Downloaded from www.Manualslib.com manuals search engine Vehicle Dimensions*
Wheelbase SiT10516
.............. 100.5 inches (255.3 cm)
SIT10506
.............. 107.0 inches (271.8 cm)
S10516
............... 175.0 inches (444.5 cm)
T10516
............... 175.4 inches (445.5 cm)
SiT10506
.............. 181.5 inches (461.0 cm)
S10516
................ 66.0 inches (167.6 cm)
T10516
................ 66.9 inches (170.0 cm)
S10506
................ 65.9 inches (167.4 cm)
T10506
................ 67.0 inches (170.2 cm)
Length
Height Width
................... 67.8
inches (1 72.2 cm)
Front Tread
S Series ................ 55.0 inches (1 39.6 cm)
T Series ................ 57.3 inches (145.4 cm)
S Series ................ 54.7 inches (1 38.8 cm)
T Series ................ 55.1 inches (139.9 cm)
Rear Tread
*Figures reflect base equipment only.
6-66