
Downloaded from www.Manualslib.com manuals search engine I 
Driving  in  Rain  and on Wet Roads Rain ana wet roads can  mean driving trouble.  On a wet 
road,  you can’t stop, accelerate  or turn  as well  because 
your  tire-to-road  traction  isn’t as good as  on 
dry roads. 
And,  if your  tires don’t have  much tread left, you’ll get 
even less traction. It’s always wise  to 
go slower and be 
cautious  if rain starts 
to fall while  you are driving.  The 
surface  may get wet  suddenly  when your reflexes are 
tuned  for  driving  on dry pavement. 
The  heavier  the rain, the harder  it is to see. Even  if your 
windshield wiper blades are  in  good shape, a heavy  rain 
can make it harder  to see  road  signs  and traffic signals, 
pavement markings,  the  edge of the  road  and even 
people walking. 
i 
K, 
It’s  wise  to  keep your wiping equipment  in good  shape 
and  keep your windshield washer tank filled  with 
washer  fluid. Replace your windshield wiper inserts 
when  they  show signs 
of streaking  or missing  areas on 
the windshield,  or when  strips 
of rubber start  to separate 
from  the inserts. 
4-15   

Downloaded from www.Manualslib.com manuals search engine The most  important advice on freeway driving is: Keep 
up  with  traffic  and  keep 
to the right.  Drive  at  the  same 
speed  most  of  the  other drivers  are driving.  Too-fast  or 
too-slow  driving  breaks a smooth  traffic  flow.  Treat  the 
left  lane 
on a freeway  as a passing  lane. 
At  the  entrance, there  is  usually a ramp  that  leads  to the 
freeway. 
If you have  a clear  view of the freeway  as you 
drive along  the entrance  ramp,  you  should  begin 
to 
check traffic.  Try  to determine where you expect to 
blend  with  the  flow.  Try  to merge  into the gap  at close to 
the  prevailing  speed. Switch 
on your  turn  signal, check 
your  mirrors  and  glance  over your  shoulder  as often  as 
necessary.  Try  to blend  smoothly  with  the  traffic  flow. 
Once  you are on the  freeway,  adjust your speed to  the 
posted  limit or to the  prevailing rate  if it’s  slower.  Stay 
in  the  right  lane unless 
you want  to pass. 
Before changing lanes, check  your  mirrors. Then use 
your  turn signal. 
Just  before 
you leave  the lane, glance  quickly over your 
shoulder to make sure there  isn’t another vehicle  in your 
“blind” spot. 
Once 
you are  moving  on  the  freeway,  make certain you 
allow  a reasonable following distance. Expect  to  move 
slightly  slower 
at night.  When 
you want 
to leave  the  freeway,  move to the  proper 
lane  well  in  advance.  If  you miss your  exit, do not, 
under  any  circumstances, stop  and  back  up.  Drive 
on to 
the  next  exit. 
The  exit ramp  can  be  curved, sometimes quite  sharply. 
The exit speed  is  usually  posted. 
Reduce your  speed according 
to your  speedometer,  not 
to your sense of motion.  After  driving for any  distance 
at  higher  speeds, 
you may  tend to think  you  are going 
slower  than 
you actually  are. 
Before  Leaving  on a Long  Trip 
Make sure  you’re  ready.  Try  to  be  well  rested.  If  you 
must  start  when  you’re  not  fresh 
-- such  as after a day’s 
work 
-- don’t  plan to make too  many  miles  that  first part 
of  the  journey.  Wear comfortable clothing and shoes 
you 
can easily  drive in. 
Is your vehicle  ready  for a long trip?  If you keep it 
serviced  and maintained,  it’s  ready  to go. If it needs 
service,  have  it done before starting out.  Of course, 
you’ll  find experienced  and able service experts  in  GM 
dealerships  all across 
North America. They’ll  be  ready 
and  willing  to  help 
if you need it.   

Downloaded from www.Manualslib.com manuals search engine Tie a red cloth to your  vehicle to  alert  police  that 
you’ve  been  stopped by the  snow. 
Put on extra clothing  or wrap  a blanket  around you. 
If  you  have no  blankets  or extra clothing,  make  body 
insulators from newspapers, burlap  bags, rags, floor 
mats 
-- anything  you can wrap  around  yourself  or 
tuck  under  your clothing 
to keep warm. 
Sr Y can  trap  exha.  ler your  vehicle. 
~ This  can  cause  deadly 60 (carbon  monoxide)  gas 
to  get  inside.  CO could  overcome  you and  kill 
you. 
You can’t  see  it or smell  it, so you  might  not 
know 
it is  in  your  vehicle.  Clear away snow  from 
around  the  base  of your  vehicle,  especially  any 
~ that  is  blocking  your  exhaust  pipe.  And  check 
around  again  from  time  to  time  to  be  sure  snow 
doesn’t  collect  there. 
Open  a  window  just 
a little  on  the  side  of the 
vehicle  that’s 
away from  the  wind.  This  will help 
~ keep  CO out. 
Run your  engine  only as long as you  must.  This saves 
fuel.  When  you  run 
the engine,  make it go a little  faster 
than  just idle.  That  is,  push  the  accelerator slightly. This 
uses less fuel  for the  heat  that you get  and it keeps  the 
battery  charged.  You will  need  a well-charged  battery 
to 
restart  the  vehicle,  and  possibly  for signaling  later  on 
with  your  headlamps.  Let 
the heater  run  for a while. 
You  can run  the  engine to  keep  warm, but  be careful. 
4-25   

Downloaded from www.Manualslib.com manuals search engine Making  Turns 
NOTICE: 
Making  very  sharp  turns  while  trailering  could cause  the  trailer 
to come  in  contact  with  the 
vehicle. 
Your vehicle  could  be  damaged.  Avoid 
making  very  sharp  turns  while  trailering. 
When  you’re  turning  with  a trailer,  make  wider turns than 
normal. Do this so your  trailer  won’t  strike soft shoulders, 
curbs,  road  signs,  trees  or  other  objects.  Avoid  jerky  or 
sudden  maneuvers.  Signal  well 
in advance. 
Turn  Signals  When  Towing a Trailer 
When  you  tow a trailer, your vehicle has to have  extra 
wiring  (included  in the optional  trailering  package). 
The  arrows  on your  instrument  panel will flash 
whenever  you signal  a turn  or  lane  change.  Properly 
hooked 
up, the trailer lamps 
drivers  you’re about to turn,  will 
also  flash,  telling other 
change  lanes  or stop.  When 
towing  a  trailer, the arrows  on your  instrument 
panel  will  flash 
for turns even if the bulbs on the trailer 
are burned out.  Thus, you  may  think drivers behind  you 
are seeing your signal  when  they are not. It’s important 
to  check  occasionally  to be  sure  the trailer bulbs  are 
still  working. 
Driving  On  Grades 
Reduce speed  and shift to  a  lower  gear before you start 
down  a long  or  steep  downgrade.  If  you don’t shift 
down,  you  might  have to  use  your  brakes 
so much that 
they  would  get hot  and  no  longer work well. 
On  a long uphill grade, shift  down  and reduce your 
speed 
to around 45 mph (70 kdh)  to reduce  the 
possibility  of engine  and transmission  overheating. 
When  towing 
at high altitude on  steep uphill grades, 
consider  the  following:  Engine  coolant  will boil at  a 
lower temperature than  at normal altitudes.  If  you turn 
your  engine  off immediately after towing  at high altitude 
on  steep  uphill grades, your vehicle  may  show signs 
similar to  engine  overheating. 
To avoid this, let  the 
engine 
run while parked  (preferably on level ground) 
with  the automatic  transmission  in 
PARK (P) for  a few 
minutes  before  turning  the  engine  off. If  you  do get  the 
overheat warning,  see  “Engine  Overheating”  in 
the  Index. 
4-35   

Downloaded from www.Manualslib.com manuals search engine Parking on Hills 
You  really  should  not  park  your vehicle,  with  a trailer 
attached, 
on a  hill.  If  something  goes wrong,  your  rig 
could  start 
to move.  People  can be  injured,  and  both 
your  vehicle  and 
the trailer  can be  damaged. 
But  if  you  ever have 
to park  your  rig on a hill, here’s 
how  to do 
it: 
1.  Apply  your  regular  brakes,  but  don’t  shift  into 
2. Have  someone  place chocks  under  the  trailer  wheels. 
3. When  the  wheel  chocks are in  place,  release  the 
regular  brakes  until  the  chocks absorb the  load. 
4. Reapply the regular  brakes.  Then apply  your  parking 
brake,  and  shift  to 
PARK (P). 
5. Release  the  regular  brakes. 
PARK (P) yet. 
When You Are Ready  to  Leave  After 
Parking  on  a  Hill 
1. Apply  your  regular  brakes  and  hold  the  pedal  down 
while 
you: 
0 Start  your  engine; 
Shift  into a gear; and 
Release  the  parking  brake. 
2. Let  up  on  the  brake  pedal. 
:ks. 
3. Drive  slowly until the  trailer is clear of the  choc 
4. Stop and  have  someone pick  up  and  store  the  chocks. 
Maintenance  When  Trailer  Towing 
Your vehicle  will  need  service  more  often  when  you’re 
pulling  a trailer.  See the  Maintenance  Schedule  for more 
on this.  Things  that are especially  important  in  trailer 
operation  are automatic  transmission  fluid  (don’t 
overfill),  engine oil,  axle  lubricant,  belt,  cooling  system 
and  brake  adjustment.  Each 
of these  is covered  in  this 
manual,  and  the  Index  will  help 
you find  them  quickly. 
If  you’re  trailering,  it’s  a good  idea 
to review  these 
sections  before  you start  your  trip. 
Check  periodically  to  see that  all  hitch  nuts  and  bolts 
are  tight. 
4-36   

Downloaded from www.Manualslib.com manuals search engine Engine  Fan  Noise 
This vehicle  has  a clutched engine  cooling fan. When 
the  clutch  is  engaged, the fan spins  faster  to  provide 
more  air to  cool  the  engine. In most  everyday  driving 
conditions,  the  clutch  is  not 
fully engaged. This 
improves  fuel  economy  and  reduces  fan  noise.  Under 
heavy  vehicle  loading,  trailer towing  andor high 
outside  temperatures,  the  fan speed  increases  when  the 
clutch engages. 
So you  may  hear  an  increase  in  fan 
noise.  This is  normal  and  should  not  be  mistaken 
as the 
transmission  slipping  or making  extra shifts.  It  is  merely 
the cooling  system  functioning properly. The fan will 
slow  down  when  additional  cooling 
is not  required  and 
the  clutch  disengages. 
You may also hear  this  fan  noise  when  you  start  the 
engine.  It  will  go  away 
as the  fan  clutch  disengages. 
If a  Tire  Goes  Flat 
It’s unusual  for a tire  to “blow out” while  you’re  driving, 
especially 
if you  maintain  your  tires  properly. If air  goes 
out  of 
a tire,  it’s  much  more  likely  to  leak out slowly. 
But 
if you  should  ever have a “blowout,”  here  are a few 
tips  about  what  to  expect  and  what 
to do: 
If a front  tire  fails,  the  flat tire  will  create a drag that 
pulls  the  vehicle  toward  that  side.  Take  your  foot off 
the 
accelerator  pedal  and  grip the steering  wheel  firmly. 
Steer 
to maintain  lane  position,  and  then  gently  brake  to 
a stop well  out of the  traffic  lane. 
A rear  blowout,  particularly  on a curve,  acts  much  like a 
skid  and  may  require  the  same  correction  you’d  use  in a 
skid. In any  rear  blowout,  remove your  foot  from the 
accelerator  pedal.  Get  the  vehicle  under  control  by 
steering  the  way  you  want  the  vehicle to go.  It  may  be 
very  bumpy  and  noisy,  but  you  can  still  steer.  Gently 
brake  to 
a stop -- well  off  the  road  if possible. 
If 
a tire  goes  flat, the next  part  shows how  to  use  your 
jacking  equipment  to  change a flat tire  safely. 
5-22   

Downloaded from www.Manualslib.com manuals search engine / 18 24 
5 11 17 23 c7 c7 c7 17 
4 ~ 10 16 
3 9 15 21 c7 E7 c7 E7 
2 8 14 20 c7 c7 11 17 
7 13 19 E7 c7 c7 E3 
FuseKircuit 
Breaker  Usage 
4 
8 
9 
2 
3 
FuseKircuit Breaker 
Usage I 
1 Stop/Turn/Hazard Lamps,  CHMSL, 
! Chime Module 
Not Used 
Courtesy Lamps, Power Outside 
Mirrors, Glove 
Box Lamp,  Dome 
Reading Lamps,  Vanity Mirror Lamps 
10 
11 
DRL Relay,  DRL  Module, Chime 
Headlamp Switch, Keyless  Entry, 
Cluster, Overhead Console, Interior 
Lamps Module 
Not  Used 
Cruise Module, Cruise Control Switch 
Power Outlets, DLC, Subwoofer 
Amplifier  Starter Enable Relay 
I 
License Plate Lamp, Taillamps, I 
Parking Lamps, Ashtray Lamp, Panel 
Lights, Trailer Taillamps, Front and 
Rear Sidemarker Lamps, Door Switch 
Illumination, Headlamp Switch 
Illumination, Rear  Seat Audio 
Illumination 
Air 
Bag System 
Wiper  Motor,  Washer  Pump, Upfitter 
Relay Coil   

Downloaded from www.Manualslib.com manuals search engine Fuse/Circuit Breaker  Usage 
UPFIT-BATT  Upfitter Battery Power  Stud, Trailer 
UPFIT-ACCY  Upfitter Accessory Relay 
Wiring 
Harness 
Spare 
Fuse  Puller* 
Spare 
Spare 
ECM-B 
HORN 
A/C  COMP 
RR DEFOG 
ENG-I 
Fuse/Circuit  Breaker  Usage 
IGN-E 
ECM-I 
Not  used 
LIGHTING 
Not  used 
Not  used  Fuel  Pump Relay and  Motor, VCM, 
Oil  Pressure  Switch/Sender 
Horn  Relay and Horn 
A/C Enable  Relay and Compressor 
Heater-A/C  Control  Selector  Switch, 
Rear  Window  Defogger 
Oxygen  Sensors,  Camshaft Position 
Sensor, Mass Air Flow  Sensor, 
Evaporative  Emission  Canister  Purge 
Solenoid,  Linear  EGR  Valve 
Solenoid,  VCM  EGR  HI  BATT 
IGN  A 
IGN B 
ABS 
NC 
RR HTRIAC 
Spare  A/C 
Enable  Relay Coil 
Fuel Injectors 
1-6, Crankshaft 
Position  Sensor, VCM, Coil Driver 
Module (EST) 
Park  Lamps  Fuse, DRL Fuse, 
Headlamp and Panel Dimmer Switch 
SteeringBecurity  Fuse,  Courtesy 
Fuse,  ACSY  CB, Stop/Hazard  Fuse, 
Auxiliary Power Fuse, Cigar Lighter 
Fuse,  Radio  Battery Fuse 
Starter  Relay, Ignition Switch 
Ignition  Switch 
Electronic Brake Control Module  Blower Motor Resistor, Blower 
Relay 
Auxiliary Heater  NC Relay 
Not  used 
*A  fuse  puller  is included 
in the  underhood electrical 
center.  You will also find  spare fuses. 
6-65