1998 AUDI A4 Suspension Wheel Alignment Workshop Manual

44-34

Extending the springs (standard, sport and
heavy duty (1BP) suspensions

CAUTION!

Make sure that the wheels do not lose
contact with the turntables during the lifting
operation.
If wheels do lose contact, do not move the
turntables. Otherwise incorrect
measurements will result.

- Raise vehicle at front jacking points.

Vehicle is now in position B2 page 44
-27
- Lift cylinders out of threaded spindles and secure in position using
locking pins.
- Make sure locking pins (arrows) are correctly positioned.
- Lower vehicle down onto spacer gauge.
Pa
ge 33 of 37 Wheel ali
gnment
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.44.2

44-35

Extending the springs (heavy duty
suspension (1BB)

CAUTION!

Make sure that the wheels do not lose
contact with the turntables during the lifting
operation.
If wheels do lose contact, do not move the
turntables. Otherwise incorrect
measurements will result.

- Raise vehicle at front jacking points.

Vehicle is now in position B2 page 44
-27
- Lift cylinders out of threaded spindles and secure in position using
locking pins.
- Make sure locking pins (arrows) are correctly positioned.
- Remove VAG1925/6 adapter.
- Lower vehicle down onto spacer gauge.
Pa
ge 34 of 37 Wheel ali
gnment
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.44.2

44-36

Note:
The wheel alignment program determines the
current right and left toe constant (actual values
of C2 - C1 page 44
-27
). The program checks
whether the current toe constant (actual value)
lies within the tolerance (control value) vehicle
alignment specifications tables, pages 44
-11
and
Page 44
-13
.

- If toe constant actual value lies outside control value tolerance, adjust
toe value constant within adjusting value tolerance.

Front-wheel-drive vehicles page 44
-11

All-wheel-drive vehicles page 44
-13
Pa
ge 35 of 37 Wheel ali
gnment
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.44.2

44-37

Adjusting toe constant "S"

Checking toe constant after adjusting
The alignment unit checks the toe constant again. - Loosen nut -A-.
- Back out bolt -B- approx. 4 mm (1/8 in.).
- Push tie rod end downward onto stop.
- Turn in adjusting bolt -B- until exact specifications are achieved.
- Tighten nut -A- to 45 Nm (33 ft lb) and check values.
- Tighten bolt -B- to 7 Nm (62 in. lb).
- Lower vehicle to defined starting position B1.
- Screw threaded spindle down.
- On vehicles with standard suspension, bounce suspension several
times.
If the second check shows that the values are within the check value
tolerance, the setting is OK. If the values are outside the check value tolerance, the setting must
be adjusted again in position B2. Position B2: + 60 mm (2.36 in.).
Pa
ge 36 of 37 Wheel ali
gnment
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.44.2

44-38

Front axle toe-in, setting


- Loosen lock nut -B-.

Make sure that the boots are not twisted after turning the tie rods
Note:
Twisted boots will wear out quickly.
After tightening lock nut -B- it is possible that the toe value may deviate
slightly.
If the measured toe lies within the tolerances, the adjustment is correct. - Adjust toe on left and right at hex -A-.
- Tighten lock nut -B- and check toe-in again.
Tightening torque: 40 Nm (30 ft lb)
Pa
ge 37 of 37 Wheel ali
gnment
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU01.44.2