Page 25 of 44
38-25
All:
- Remove valve body from transmission while
advancing the wiring harness connector.
Note only for Park/Neutral Position (PNP)
Switch -E17-:
Do not place the removed valve body on the
Sensor for transmission RPM at rear of valve
body. Danger of damage.
Installing
- Lightly coat O-rings of wiring harness connector
with ATF.
- Insert wiring harness connector into
transmission housing.
Installation position: Flat part of rear collar
points downward, the tabs at collar are
horizontal
Only for transmission with hydraulic control
E18/2
- Route wire with connector -C- according to illustration, so that the wire
is not pinched when installing the valve body.
Pa
ge 25 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 27 of 44
38-27
Only for transmission with hydraulic control
E18/2
Only for Park/Neutral Position (PNP) Switch -E17- - Pull wiring with connector -B- of Sensor for transmission RPM -G182-
between valve body and wiring harness upward.
- Connect connector -B- to connector -A- at wiring harness.
- Connect connector -C- to Transmission Vehicle Speed Sensor (VSS) -
G38-.
- Connect connector (arrow) to Transmission Vehicle Speed Sensor
(VSS) -G38-.
Pa
ge 27 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 28 of 44
38-28
All:
Tightening torque - Connect clip to wiring harness connector (arrow).
- Installing oil strainer page 38
-21
.
- Installing oil pan page 38
-20
.
- Fill up ATF page 37
-140
.
Component
Nm
Valve body to transmission housing (from inside out) 8
Pa
ge 28 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 42 of 44
38-42
Wiring harness in transmission,
removing and installing
Removing
- Removing valve body page 38
-22
.
Only for Park/Neutral Position (PNP) Switch -E17- - Lever out retainer straps of connectors at solenoid valves using a small
screwdriver and disconnect connectors -A- in sequence.
- Unhook wiring harness at side retainer straps -B- of valve body.
- Turn valve body on its back side and loosen connector at Sensor for
transmission RPM -1-.
- Remove retaining clip (arrow A) and unclip wiring harness from
retaining clip (arrow B).
- Disconnect connector -2- from Solenoid Valve 4 -N91-.
Pa
ge 42 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 43 of 44
38-43
Only for transmission with hydraulic control
E18/2
Installing, valid for all:
Installation is reverse of removal, noting the following: - Turn valve body on its back side and loosen connector at Sensor for
transmission RPM -1-.
- Remove retaining clip (arrow A) and unclip wiring harness from
retaining clip (arrow B).
- When installing, connect connectors of wiring harness to the
corresponding solenoid valves.
- Clip wiring harness into the respective retaining clips. In case of
deviations, the wiring harness can be pinched during installation of the
valve body.
- Installing valve body page 38
-25
.
- Fill up ATF page 37
-140
.
Pa
ge 43 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 44 of 44
38-44
Transmission Fluid Temperature Sensor
-G93-, replacing
Note:
Transmission Fluid Temperature Sensor -G93- is
integrated in the transmission wiring harness.
Removing
- Remove wiring harness in transmission page
38
-42
.
Installing
Installation is the reverse of removal. Also carry
out the following procedure.
- Replace wiring harness with a new one.
Pa
ge 44 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1