SS0DM-02
- SERVICE SPECIFICATIONSENGINE MECHANICAL (2JZ-GTE)
SS-9
166 Author: Date:
1997 SUPRA (RM502U)
ENGINE MECHANICAL (2JZ-GTE)
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,079 kPa (11.0 kgf/cm2, 156 psi) or more
883 kPa (9.0 kgf/cm2, 128 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Valve
clearanceat cold Intake
Exhaust
Adjusting shim (for repair part) Mark 2.500
Mark 2.550
Mark 2.600
Mark 2.650
Mark 2.700
Mark 2.750
Mark 2.800
Mark 2.850
Mark 2.900
Mark 2.950
Mark 3.000
Mark 3.050
Mark 3.100
Mark 3.150
Mark 3.200
Mark 3.250
Mark 3.3000.15 - 0.25 mm (0.006 - 0.010 in.)
0.25 - 0.35 mm (0.010 - 0.014 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC110° BTDC @ idle
Idle speed650 ± 50 rpm
Timing belt
tensionerProtrusion (from housing side)8.0 - 8.8 mm (0.315 - 0.346 in.)
Cylinder headWarpage
Cylinder block side Maximum
Intake manifold sideMaximum
Exhaust manifold side Maximum
Valve guide bore diameter STD
O/S 0.05
Valve seat
Refacing angle
Contacting angle
Contacting width Intake
Exhaust
Cylinder head bolt diameter STD
Minimum
0.10 mm (0.0039 in.)
0.10 mm (0.0039 in.)
0.10 mm (0.0039 in.)
10.985 - 11.006 mm (0.4325 - 0.4333 in.)
11.035 - 11.056 mm (0.4344 - 0.4353 in.)
15°, 45°, 75°
45°
1.0 - 1.4 mm (0.039 - 0.055 in.)
1.2 - 1.6 mm (0.047 - 0.063 in.)
10.8 - 11.0 mm (0.425 - 0.433 in.)
10.7 mm (0.421 in.)
Valve guide
bushingInside diameter
Outside diameter (for repair part) STD
O/S 0.056.010 - 6.030 mm (0.2366 - 0.2374 in.)
11.033 - 11.044 mm (0.4344 - 0.4348 in.)
11.083 - 11.094 mm (0.4363 - 0.4368 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust98.29 - 98.79 mm (3.8697 - 3.8894 in.)
98.84 - 99.34 mm (3.8913 - 3.9110 in.)
98.19 mm (3.8657 in.)
98.74 mm (3.8874 in.)
44.5°
5.970 - 5.985 mm (0.2350 - 0.2356 in.)
5.965 - 5.980 mm (0.2348 - 0.2354 in.)
SS0D9-01
- SERVICE SPECIFICATIONSCLUTCH
SS-35
192 Author: Date:
1997 SUPRA (RM502U)
CLUTCH
SERVICE DATA
Pedal height from asphalt sheet146.2 - 156.2 mm (5.76 - 6.15 in.)
Pedal freeplay5.0 - 15.0 mm (0.197 - 0.591 in.)
Push rod play at pedal top1.0 - 5.0 mm (0.039 - 0.197 in.)
Full pedal stroke132.0 - 138.0 mm (5.20 - 5.43 in.)
Clutch release point from pedal full stroke end position25 mm (0.98 in.) or more
Disc rivet head depth Max.0.3 mm (0.012 in.)
Disc runout Max.0.8 mm (0.031 in.)
Diaphragm spring out non-alignment Max.0.5 mm (0.020 in.)
Diaphragm spring finger wear (Depth)Max.0.6 mm (0.024 in.)
Diaphragm spring finger wear (Width)Max.5.0 mm (0.197 in.)
Flywheel runoutMax.0.1 mm (0.004 in.)
Flywheel damper rotational freeplay STD105 mm (4.134 in.)
