1997 TOYOTA CAMRY lights

4
1. Engine coolant temperature gauge
2. Service reminder indicators or
indicator lights
3. Fuel gauge4. Speedometer
5. Odometer and two trip meters
6. Theft deterrent system indicator
light7. Tachometer
8. Trip meter reset knob
9. Low fuel level warning light
Instrument cluster overview
ProCarManuals.com

6
Automatic transmission indicator light.Traction control system off
indicator/warning light *1
Turn signal indicator lights.
Headlight high beam indicator light
Overdrive-of f indicator lighrt.
Cruise control indicator light*
2
Slip indicator light.
*1: For details, see Service reminder indicators and
warning buzzersº in Chapter 1-5.
*
2: If this light flashes, see Cruise controlº in Chapter 1-6.
ProCarManuals.com

10
Locking operation
Unlocking operationsYour vehicle has a wireless remote
control system that can lock or unlock
all the doors, or sound an alarm of the
theft deterrent system from a distance
within approximately 1 m (3 ft.) of the
vehicle.
LOCKING AND UNLOCKING THE
DOORS
To lock and unlock all the doors, push
the switches of the transmitter slowly
and surely.
To lock: Push the ºLOCKº switch. All the
doors are locked simultaneously. At this
time, parking lights, side marker lights and
tail lights flash.
Check to see that the doors are securely
locked.
If any of the doors is not securely closed,
or if the key is in the ignition switch, locking
cannot be performed by the LOCKº
switch.
To unlock: Push the UNLOCKº switch
once to unlock the driver's door alone.
Pushing the switch twice within 3 seconds
unlocks all the doors simultaneously. At
this time, parking lights, side marker lights
and tail lights flash twice.You have 30 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
doors will be automatically locked again.
If the LOCKº or UNLOCKº switch is kept
pressed in, the locking or unlocking
opeartion is not repeated. Release the
button and then push again.
ÐWireless remote control
ProCarManuals.com

11
PANICº SWITCH
Pushing the PANICº switch for 2 sec-
onds blows the horn intermittently
and flashes the headlights, tail lights
and other exterior lights. The engine
cannot be started because the starter
circuit will be cut.
The PANICº switch is used to deter the
vehicle theft when you witness anyone at-
tempting to brake into or damage your ve-
hicle.
The alarm will last for one minute. To
stops this in the midway, push the PAN-
ICº switch once again. The starter circuitcut will be kept on until the PANICº mode
is cancelled.
To cancel the PANICº mode, unlock any
door with the key or tranmitter or turn the
ignition key from the LOCKº to ACCº
position.
The PANICº mode does not work when
the key is inserted in the ignition switch.
WIRELESS REMOTE CONTROL
TRANSMITTER
The wireless remote control transmitter is
an electronic component. Observe the fol-
lowing instructions in order not to cause
damage on the transmitter.

Do not leave the transmitter on the
places where the temperature becomes
high such as on the dashboard.

Do not disaassemble it.

Avoid knocking it hard against other ob-
jects or dropping it.

Avoid putting it in water.
You can use up to 2 wireless remote con-
trol transmitters for the same vehicle.
Contact your Toyota dealer for detailed in-
formation.
If the wireless remote control transmitter
doew not actualte the doors or alarm, or
operate from a normal distance:
Check for closeness to a radio transmit-
ter such as a radio station or an airport
which can interfer with normal operation
of the transmitter.

The batteries may have been con-
sumed. Check the batteries in the trans-
mitter. To replace the batteries, see Re-
placing transmitter batteries.º
Replacing transmitter batteries
The expected lift of your transmitter bat-
teries is about one year. For replacement,
use DURACELL
[ DL2016 or equivalent.
a. Using a screwdriver, separate the two
halves of the transmitter with the transmit-
ter buttons facing down.
b. Remove and replace the transmitter
batteries.If yout touch a new battery with
your fingers, clean it with rubbing alcohol.
Skin oils may shorten the batteries' life.
c. Reassemble the transmitter case.
Make sure the gasket is properly installed
.After replaceing batteries, check that the
transmitter operates properly. If the trans-
mitter still does not operate properly, con-
tact your Toyota dealer.
ProCarManuals.com

16
2. In front of the vehicle, pull up on the
auxiliary catch lever and lift the
hood.3. Hold the hood open by inserting
the support rod into the slot.
Before closing the hood, check to see that
you have not forgotten any tools, rags,
etc. and return the support rod to its clip-
this prevents rattles. Then lower the hood
until make sure it locks into place. If nec-
essary, press down gently on front edge to
lock it.
CAUTION!
After inserting the support rod into
the slot, make sure the rod supports
the hood securely.
To deter the vehicle theft, the system is
designed to give an alarm and keep the
engine from being started if any of the
doors, trunk or hood is forcibly un-
locked or the battery terminal is dis-
connected and then reconnected
when the vehicle is locked.
The alarm blows the horn intermittently
and flashes the headlights, tail lights and
other exterior lights. The engine cannot
be started because the starter circuit will
be cut.
Theft deterrent systemÐ
ProCarManuals.com

59
To adjust the rear view mirror, simply op-
erate the control lever.
NOTICE
If ice should jam the mirror, do not
operate the control or scrape the
mirror fce. Use a spray de-icer to
free the mirror.
To adjust a mirror, use the switches.
1. Master switchÐTo select the mirror to
be adjusted
Place the switch at Lº (left) or Rº (right).
2. Control switchÐTo move the mirror
push the switch in the desired direc-
tion.
If the engine is not running, the key must
be in the ACCº position.
NOTICE
If ice should jam the mirror, do not
operate the control or scrape the
mirror face. Use a spray de-icer to
free the mirror.
To reduce glare from the headlights of
the vehicle behind you during night
driving, operate the lever on the lower
edge of the mirror.
Daylight drivingÐLever at position 1
The reflection in the mirror has greater
clarity at this position.
Night drivingÐLever at position 2
Remember that by reducing glare you
also lose some rear view clarity.
ÐRear view mirror remote
controlÐPower rear view mirror
controlAnti-glare inside rear view
mirror
ProCarManuals.com

Part 1Headlights and turn signals
61
OPERATION OF
INSTRUMENTS AND
CONTROLSÐ
Chapter 1-4
Lights, Wipers
and Defogger

Headlights and turn signals

Emergency flashers

Instrument panel light control

Interior light

Ignition switch light

Personal light

Windshield wipers and washer

Rear window and outside rear
view mirror defoggersHEADLIGHTS
To turn on the following lights: Twist
the headlight/turn signal lever knob.
Position 1ÐParking, tail, license plate,
side marker and instrument panel lights
Position 2ÐHeadlights and all of the
above
The lights automatically turn off when the
driver's door is opened with the ignition
turned off. To turn them on again, turn the
key to the ONº position or actuate the
headlight switch. If you are going to park
for over one week, make sure the head-
light switch is off.
NOTICE
To prevent the battery from being
discharged, do not leave the lights
on for a long period when the
engine is not running.
Daytime running light system (Canada
only)
The headlights turn on when the parking
brake is released with the engine started,
even with the light switch in the OFFº
position. They will not go off until the igni-
tion switch is turned off.
To turn on the other exterior lights and in-
strument panel lights, twist the knob to the
position 1.
Under the daytime running light system,
the headlights turn on at reduced intensi-
ty. Twist the knob to the position 2 to turn
to full intensity for driving at night.
ProCarManuals.com

62
High-Low beamsÐFor high beams,
turn the headlights on and push the lever
away from you (position 1). Pull the lever
toward you (position 2) for low beams.
The headlight high beam indicator light
(blue light) on the instrument panel will tell
you that the high beams are on.
Flashing the high beam headlights
(position 3)ÐPull the lever all the way
back. The high beam headlights turn off
when you release the lever.
You can flash the high beam headlights
with knob turned to OFFº.TURN SIGNAL
To signal a turn, push the headlight/
turn signal lever up or down to posi-
tion 1.
The key must be in the ONº position.
The lever automatically returns after you
make a turn, but you may have to return
it by hand after you change lanes.
To signal a lane change, move the lever
up or down to the pressure point (position
2) and hold it.
If the turn signal indicator lights (green
lights) on the instrument panel flash faster
than normal, a front or rear turn signal bulb
is burned out.To turn on the emergency flashers,
push the switch.
All the turn signal lights will flash. To turn
them off, push the switch once again.
Turn on the emergency flashers to warn
other drivers if your vehicle must be
stopped where it might be a traffic hazard.
Always pull as far off the road as possible.
The turn signal light switch will not work
when the emergency flashers are operat-
ing.
Emergency flashers
ProCarManuals.com