1997 RENAULT KANGOO diagram

UPPER REAR STRUCTURE
Side panel lining
44C
PRB4415
INTRODUCTION
The replacement of this part is a complementary
operation to the wing panel or a side panel for a
rear side impact.
It also requires replacement of the centre pillar
reinforcement, the door pillar will need to be or-
dered separately.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective section.
This part is replaced in three ways (see cuts on the
diagram below) :
1 - complete
2 - partial by cut A-A
3 - partial by cut B.B for glazed version
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with welded nuts.
JOINTS WITH :
Door pillar upper reinforcement or centre pillar
reinforcement
Roof stretcher lining
Lights mounting side panel rain channel
Sill panel closure panel
Sill panel closure panel, rear section
Rear wheel arch
Rear end cross member
PARTS CONCERNED (thickness in mm):
1Rear wing panel lining 0.7
2Stretcher lining 0.7
3Lights mounting side panel rain
channel 1.2
4Rear wing panel extension 1
5Side panel rain channel
upper reinforcement 1.2
6Sill panel closure panel 1.5
7Sill panel closure panel, rear section 1.5
8Door pillar upper reinforcement 1.2
9Door pillar lower reinforcement 1.2
10Inertia reel mounting reinforcement 1.5
11Inner wheel arch 1
12Seat mounting reinforcement 1.5
13Rear end cross member 1.2
44-17

UPPER REAR STRUCTURE
Lights mounting side panel rain channel
44F
PRB4418
INTRODUCTION
The replacement of this part may be carried out in
two ways :
1 - Complete replacement, complementary to the
side panel with lining.
2 - Partial replacement, complementary to the
rear end panel and rear end cross member
(see cut in the diagram below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- side panel extension,
- lights mounting with studs and welded nuts,
- bumper counter blade,
- tailgate counter balance reinforcement,
- welded nuts,
- upper hinge reinforcement.
JOINTS WITH:
Panel upper rain channel
Side panel lining
Rear floor
Rear end cross member
Roof stretcher lining
Roof
PARTS CONCERNED (thickness in mm):
1Lights mounting side panel rain
channel 1.5
2Panel upper rain channel 1.2
3Panel lining 0.7
4Rear floor 0.8
5Rear end cross member 1.02
6Roof stretcher 0.7
7Roof 0.7
8Wheel arch 1
9Side panel 1
10Rear wing panel extension 1
or
44-33

UPPER REAR STRUCTURE
Rear wing panel extension
44G
PRB4419
INTRODUCTION
The replacement of this part is carried out partial-
ly following a rear side impact and is complemen-
tary to the rear wing panel (see diagram and me-
thod below).
The bumper side mounting must also be replaced
and is sold separately.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
JOINTS WITH:
Wing panel lining
Lights mounting side panel rain channel
Bumper mounting
PARTS CONCERNED (thickness in mm):
1Rear wing panel extension 1
2Wing panel lining 0.7
3Acoustic insert 0.7
4Bumper mounting 1.2
44-38

UPPER REAR STRUCTURE
Rear end panel
44H
PRB4420
INTRODUCTION
The replacement of this part is a basic operation
for a rear impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
This part may be replaced partially (see cut and
diagram below).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
JOINTS WITH:
Rear end panel
Rear end cross member
Side panel rain channel
Floor
Rear pillar lower gusset
PARTS CONCERNED (thickness in mm):
1Rear end panel 1
2Rear end cross member 1.2
3Side panel rain channel 1.5
4Floor 0.8
5Rear wing panel extension 1
or
44-41