1997 RENAULT KANGOO engine

LOWER STRUCTURE
Front side member, front section
41B
PRB4122
INTRODUCTION
The replacement of this part can be done in two
ways :
A Front side member, complete front section .
B Front side member, partial front section (cut
to be made in front of the front mounting of
the sub-frame), see the following diagram.
In the two cases these are complementary opera-
tions to the replacement of the front end lower
cross member and the headlight carrier panel. As
a result, the joints with these parts will not be
considered here, they will be dealt with in the res-
pective sections.
The repair bench must be used.
The replacement of this part also requires the re-
placement of the side member closure panel
which will have to be ordered separately.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 -Side member
Part assembled with:
- engine mounting height adjuster (only on the
right hand side),
- sub-frame front mounting.
2 - Front side member closure panel
Part on its own.
JOINTS WITH:
Side member closure panel
Front side member, rear section
Front wheel arch
Shock absorber cup height adjuster
Engine mounting *
PARTS CONCERNED (thickness in mm) :
1Front side member, front section 1.5
2Front side member, rear section 2.5
3Front wheel arch 0.8
4Shock absorber cup height adjuster 0.8
5Side member closure panel 1.2
6Engine mounting height adjuster* 1.8
7Engine mounting reinforcement * 1.5
* Only the right hand side.or
41-5

LOWER STRUCTURE
Front half unit
41D
PRB4124
INTRODUCTION
The operation for the replacement of this part is
complementary to :
- the front end lower cross member,
- the headlight panel
- the cowl side panel.
This operation requires the replacement of the
cowl side panel (pillar lining) and of the cowl side
panel upper reinforcements, which have to be or-
dered separately.
In the operation described below there are only
descriptions of the specific joints to the part
concerned, information concerning the parts to
be ordered separately is not considered here. This
will be dealt with in the respective sections.
The repair bench must be used.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with:
1 Front side member , rear section
- engine mounting height adjuster (right
hand side)
- engine mounting reinforcement (right
hand side),
- engine mounting plate (right hand side),
- sub-frame front mounting,
- front side member closure panel ,
- wheel arch,
- shock absorber cup,
- shock absorber cup height adjuster,
- ABS mounting (right hand side),
- injection unit mounting and impact sensor
(left hand side).
2 Cowl side panel (pillar lining)
3 Cowl side panel upper reinforcementJOINTS WITH:
Plenum chamber
Injection unit mounting and impact sensor (left
hand side)
Front side member, rear section
Shock absorber cup height adjuster
PARTS CONCERNED (thickness in mm) :
1Plenum chamber 1
2Injection unit mounting and impact
sensor (left hand side) 2
3Front side member, front section 1.5
4Front side member, rear section 1.8
5Shock absorber cup height adjuster 1
6Shock absorber cup 2
7Cowl side panel (pillar lining) 1.5or
41-13

UPPER FRONT STRUCTURE
Cowl side panel (pillar lining), part section
42C
PRB4210
INTRODUCTION
The replacement of this part is a complementary
operation for a frontal impact to a headlight car-
rier panel.
It will be partially replaced according to the cut on
the diagram and the method below.
The replacement of this part also requires the re-
placement of the cowl side panel upper reinforce-
ments.
In the operation described below there are only
descriptions of joints specific to the part concer-
ned.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 - Cowl side panel , part assembled with :
- front wing mounting,
- impact retainer reinforcement (bonnet),
- dashboard mounting support,
- shock absorber cup height adjuster reinforce-
ment .
2 - Cowl side panel upper reinforcement, front
section.
3 - Cowl side panel upper reinforcement, rear
section.
JOINTS WITH :
Engine support plate
Shock absorber cup
Plenum chamber
PARTS CONCERNED (thickness in mm):
1Cowl side panel (pillar lining) 1.5
2Engine support plate 2
3Shock absorber cup 2
4Plenum chamber 1
5 Shock absorber cup height adjuster 1or
42-5

UPPER FRONT STRUCTURE
Cowl side panel upper reinforcement
42D
PRB4211
INTRODUCTION
The replacement of this part is complementary to
the headlight carrier panel for a frontal impact.
In the operation described below there are only
descriptions of joints specific to the part concer-
ned.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Parts only :
1 - Cowl side panel upper reinforcement, front
section.
2 - Cowl side panel upper reinforcement, rear
section.
PARTS CONCERNED (thickness in mm):
1Cowl side panel (pillar lining) 1
2Cowl side panel upper reinforcement,
front section 1
3Cowl side panel upper reinforcement,
rear section 1
4Engine support plate 2
5Shock absorber cup 2
6Shock absorber cup height adjuster 1
7Windscreen wiper mounting 1
8Front pillar 1.5
JOINTS WITH :
Cowl side panel (pillar lining)
Cowl side panel upper reinforcement, front
section
Cowl side panel upper reinforcement, rear
section
Front pillar
12892R
CAA11538R4
A
2 / 3
1
42-8

UPPER FRONT STRUCTURE
Wheel arch, front section
42E
PRB4212
INTRODUCTION
The replacement of this part is an operation for a
frontal impact and is complementary to the repla-
cement of the cowl side panel (pillar lining).
It can be carried out partially from the right hand
side (see diagram and method below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 - Part only (right hand side).
2 - Part only (left hand side).
JOINTS WITH :
Engine mounting height adjuster (right hand side)
Shock absorber cup height adjuster
Side member closure panel
Front end lower cross member (right hand side)
Cowl side panel (pillar lining)
PARTS CONCERNED (thickness in mm):
1Engine mounting 2
2Shock absorber cup height adjuster 2
3Side member closure panel 1
4Side member, front section 1.5
5Front wheel arch 1
6Front end lower cross member 1.5
7Cowl side panel (pillar lining) 1.5
or
42-12

UPPER FRONT STRUCTURE
Wheel arch
42F
PRB4213
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the cowl side pa-
nel (pillar lining) for a frontal impact.
It also requires the replacement of the cowl side
panel upper reinforcements (pillar lining), and
the use of the repair bench.
In the operation below there are only descriptions
of the joints specific to the part concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- engine mounting height adjuster (right hand
side),
- engine support plate (right hand side),
- wheel arch ,
- shock absorber cup ,
- shock absorber cup height adjuster ,
- ABS mounting (right hand side),
- injection unit and impact sensor mounting
(left hand side).
JOINTS WITH :
Plenum chamber
Side member closure panel
Front side member
Front end lower cross member
PARTS CONCERNED (thickness in mm):
1Shock absorber cup height adjuster 1
2Engine mounting height adjuster 1.5
3Engine mounting reinforcement 1.5
4Shock absorber cup 2
5Plenum chamber 1
6Side member closure panel 1
7Front side member, front section 1.5
8Front side member, rear section 2.5
9Front wheel arch 1
10Front end lower cross member 1.5
11Injection unit and impact sensor
mounting (left hand side) 2
42-17