1997 RENAULT KANGOO air condition

Check the insulation, continuity and that there is no interference resistance on the electrical line :
Computer 33 B Flywheel signal sensor
Computer 34 A Flywheel signal sensor
Repair.
JSA052.0
INJECTION
Fault finding - Status and parameter interpretation17
D7F 710
engine -
55 tracks
AFTER REPAIRStart the status and parameter check again from the beginning.
DIAG 5TDC DETECTIONFiche n° 27
XR25 aid:Status BG 3LH, incorrect illumination
No fault bargraphs should be illuminated.
When the starter motor is activated.NOTES
Check the resistance of the TDC sensor.
Replace the sensor if necessary.
Check the sensor is correctly mounted.
Repair if necessary.
Check the condition of the target (if it has been removed).
Repair if necessary.
17-185

JSA052.0
INJECTION
Fault finding - Status and parameter interpretation17
D7F 710
engine -
55 tracks
AFTER REPAIRStart the status and parameter check again from the beginning.
DIAG 16AIR CONDITIONINGFiche n° 27
XR25 aid:Status BG 10LH or 10RH incorrect illumination
No fault bargraphs should be illuminated.
NOTES
Check the insulation and continuity of lines track 5 and track 51 of the injection computer.Repair if
necessary.Consult the air conditioning fault finding.
17-197

Connect the bornier in place of the computer and check the insulation and continuity of the line:
Computer 43 6 Instrument panel
Repair.
JSA052.0
INJECTION
Fault finding - Status and parameter interpretation17
D7F 710
engine -
55 tracks
AFTER REPAIRStart the status and parameter check again from the beginning.
DIAG 19FAULT WARNING LIGHT CIRCUITFiche n° 27
XR25 aid:None
No fault bargraphs should be illuminated.
NOTES
Check the condition of the warning light and its feed.
Repair if necessary.
17-200

JSA052.0
INJECTION
Fault finding - Fault charts
17
D7F 710
engine -
55 tracks
AFTER REPAIR
Chart 2
IDLE SPEED FAULTS
Only refer to this customer complaint after a complete check using the XR25.NOTES
Erase the computer memory using G0** and carry out a road test.
Check there is fuel present
(fuel gauge faulty).
Check the fuel is of the correct type.
Check the hosesCheck no hoses are pinched
(especially after a removal operation).
Check the oil levelUse the dipstick to check if the
oil level is too high.
Check the fuel
Check the flywheelConnect the OPTIMA 5800 station to carry out the flywheel test
and follow the instructions.
Check the idle speed
regulation valveTap gently to release the valve.
Check the manifoldCheck the condition of the manifold gaskets.
Check the injectorsCheck, after removal, that the injectors do not drip.
A
17-203

JSA052.0
INJECTION
Fault finding - Fault charts
17
D7F 710
engine -
55 tracks
AFTER REPAIRErase the computer memory using G0** and carry out a road test.
Chart 3
BEHAVIOUR WHILE DRIVING
Only refer to this customer complaint after a complete check using the XR25.NOTES
Check the air filter is not deformed.
Check the fuel
Check there is fuel present
(fuel gauge faulty).
Check the fuel is of the correct type.
Check the hosesCheck no hoses are pinched
(especially after a removal operation).
Check the air filter
Check the oil levelUse the dipstick to check if the
oil level is too high.
Check the condition of the manifold gaskets.Check the inlet manifold
Check the exhaust manifold is not leaking.Check the exhaust manifold
Check, after removal, that the injectors do not drip.Check the injectors
Check the throttle body is not contaminated.Check the throttle body
Check the brake servo is not leaking (noise).Check the brake servo
A
17-205

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Engine cold, ignition on.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
5 Interpretation of
normally illuminated
bargraphsCode present
No load recognition
Illuminated if immobiliser
active
+ after ignition information
received
Locking relay control effective
Always illuminated if air
conditioning option available
Illuminates after erasing the
memory to indicate that the
operation has been carried out
correctly
Computer configured for:
Manual gearbox (G50*2*)
Automatic
transmission(G50*1*)
1
2
3
4
5
12
19
19
9
17-209

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
1 Change to status testG01*
10.NJ
Use fiche n° 27
status test side
2 No fault presentEnsure this bargraph is not
flashing, otherwise enter
G02* and turn over the fiche.
IMPORTANT: This bargraph
may flash if the vehicle has no
immobiliser. Ignore this
bargraph if fault bargraph 2 RH
side is illuminated and *22 = 2
dEF.
Repair the faulty component
the erase the memory (G0**)
and return to the status test
(G01*)
3 Battery voltage# 04
if in # 04
then # 06 13 volts < X < 14.5 volts
X < 12.7 volts
Engine speed < X < 880
rpm nominal
Engine warm, at idle speed, after fan assembly has operated at least once(air
conditioning not selected)NOTES
20
17-211

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Engine warm, at idle speed, after fan assembly has operated at least once(air
conditioning not selected)NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
4 Interpretation of
normally illuminated
bargraphs
-
Code present
No load recognition
Engine speed information
received
+ after ignition information
received
Locking relay control effective
Idle speed regulation active
Richness regulation active1
2
5
4
6
6
3
17-212