1997 RENAULT KANGOO air condition

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
Carry out a conformity check.
Check operation of the immobiliser system.AFTER REPAIR
Bargraph 4 right hand side incorrect illumination
+ AFTER IGNITION PRESENT
4
Reminder: Under normal operation :
- BG 4 right hand side illuminated ignition switch in position+after ignition
- BG 4 RH side extinguished ignition switch in a position other than +after
ignition.NOTES
Fiche n° 56
Check condition of the +after ignition fuse.
Change the fuse if necessary.
Ignition on , check for voltage of + 12 volts on track A7 of the 18 track decoder unit connector.
Are there 12 volts ?
Change the decoder unit.YES
NORepair the electrical wiring between track A7 of the 18 track decoder unit
connector and the passenger compartment fuse board.
82-6

v0406.0
IMMOBILISER
Fault finding- Interpretation of XR25 Bargraphs 82
Erase the memorised fault by entering GO** on the XR25 keyboard.
Carry out a conformity check.
Check operation of the immobiliser system.AFTER REPAIR
Bargraphs 6 left and 6 right hand side illuminated
ACCEPTANCE (CLEARANCE) OF THE SIGNAL BY THE DIESEL
SOLENOID VALVE AND CODED LINE
6
Before beginning the fault finding, switch on the ignition for longer than 30
consecutive seconds, then switch off the ignition.NOTES
Fiche n° 56
Ensure that the connector of the coded electronic unit of the solenoid valve is properly connected.
Set the XR25 to pulse sensor mode (button "G", input on terminal "Vin").
Ignition on, check for pulses on track A6 of the decoder unit connector (test with decoder unit and
solenoid valve coded electronic unit connectors connected).
Are there any pulses?
Replace the solenoid valve side electronic unit.YES
NOReplace the decoder unit.
For the diesel version, if bargraphs 6 right and 6 left are illuminated, check the impact switch.
Check the condition of the electrical wiring between track A6 of the decoder unit and track 8 of the
coded solenoid valve connector and check the 12 Volts supply and earth.
Repair if necessary.
82-9

v0406.0
IMMOBILISER
Fault finding - Fault Chart (petrol version) 82
AFTER REPAIRWhen communication has been established, deal with any illuminated fault
bargraphs.
Carry out a conformity check.
Fault Chart 1NO XR25 / COMPUTER COMMUNICATION
Lines K and L are shared between several computers, which can disrupt them. If
the fault persists, it would be prudent to check that they are not disrupting lines K
and L.
NOTES
Ensure that the XR25 is not the cause of the fault by trying to communicate with another computer on the
vehicle (air conditioning computer, injection computer ...).
Check that the ISO selector is on position S8 , that you are using the latest XR25 cassette and and the correct
access code (D56).
Check the battery voltage (U > 10.5 volts). Recharge the battery if necessary.
Ensure that the diagnostic socket is correctly fed.
Check and ensure the continuity and insulation of the wiring of tracks A3 and A4 of the decoder unit
connector.
If there is still no dialogue between the XR25 and the decoder unit , replace the decoder unit .
Check that the 18 track decoder unit connector is correctly connected.
Check that the decoder unit is correctly fed :
-earth on track A8 of the decoder unit connector
-+ before ignition feed on track A9 of the decoder unit connector.
Check the condition of the +before ignition fuse.
Replace the fuse if necessary.
82-15

v0406.0
IMMOBILISER
Fault finding - Fault Chart (petrol version) 82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 2IGNITION ON, IMMOBILISER WARNING LIGHT FLASHES
PERMANENTLY (impossible to start)
None. NOTES
no See Fault Chart 1.
Switch on the ignition.
Connect the
XR25. Use fiche n° 56, selector
on S8. Enter D56.
Is there communication between the XR25
and the decoder unit?
yes
no Replace the fuse if necessary.
yes
Check the condition of the antenna ring fuse.
Is the fuse in good condition?
no
Refer to chart for bargraph 4RH in the
section "Fault finding - Interpretation of
XR25 bargraphs ".
yes
no Carry out the programming operation if the
unit is new , if not, replace the decoder unit .
Switch on the ignition and check that
bargraph 4 RH is illuminated.
Is bargraph 4RH illuminated?
yes
A
Switch on the ignition (positive after ignition
feed) and check that
bargraph 19RH is extinguished.
Is bargraph 19RH extinguished ?
82-16

Check continuity and insulation from earth
and 12 volts of the wiring between :
2 masse
2
+AVC
4A2
Is the wiring in good condition?
v0406.0
IMMOBILISER
Fault finding - Fault Chart (petrol version) 82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 2
CONT 2
B
no Repair the wiring if faulty.decoder
bornierantenna
ring
yes
yesReplace the antenna ring .
yes
no Replace the decoder unit .
Check for voltage of + 12 volts on track A2 of
the decoder unit (decoder connector
disconnected and antenna ring connector
connected).
Is this voltage present?
yes
Replace the key.
Switch off the ignition and wait until the
immobiliser warning light flashes
(immobiliser active ). Set the XR25 to pulse
sensor mode (button "G",
input on terminal "Vin").
When switching on the ignition again, check
for a pulse on track A2 of the decoder unit
(test with decoder unit and antenna ring
connectors connected).
Is there a pulse?
82-18

v0406.0
IMMOBILISER
Fault finding - Fault Chart (petrol version) 82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 3IMMOBILISER WARNING LIGHT REMAINS PERMANENTLY ILLUMINATED
(even with ignition off) OR REMAINS PERMANENTLY EXTINGUISHED
Check that decoder unit programming has been correctly carried out.NOTES
no Replace the fuse.
yes
Check the condition of the +before ignition
fuse.
Is the fuse in good condition?
no Carry out petrol configuration G22*1*.
yes
no
Refer to the chart for bargraph 5LH in the
section "Fault finding - Interpretation of
XR25 bargraphs ".
Check that bargraph 3RH is extinguished .
Is bargraph 3RH extinguished ?
yes
no Repair the wiring.
Check continuity and insulation from earth
of the wiring between track A5 of the 18
track decoder unit connector and the
instrument panel .
Is the wiring in good condition?
Check that bargraph 5LH is extinguished .
Is Bargraph 5LH extinguished ?
yes
A
82-19

v0406.0
IMMOBILISER
Fault finding - Fault Chart (petrol version) 82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 4IGNITION ON, INJECTION WARNING LIGHT FLASHES PERMANENTLY
(impossible to start)
None.NOTES
Switch on the ignition.
Connect the XR25. Use fiche n° 56.
Selector on S8. Enter D56.
Is there communication between the XR25
and the decoder unit?
no See Fault Chart 1.
yes
no Repair the wiring .
yes
Check continuity and insulation from earth
and 12 volts of the wiring between
track A6 of the 18 track decoder unit
connector and track 19 (or 43 depending on
engine) of the injection computer.
Is the wiring in good condition ?
A
yesCheck the programming (G60*) if the
decoder unit is new, otherwise, replace the
unit.
no
Is Bargraph 19RH illuminated ?
82-21

v0406.0
IMMOBILISER
Fault finding - Fault Chart (diesel version)82
AFTER REPAIRWhen communication has been established, deal with any illuminated fault
bargraphs.
Carry out a conformity check.
Fault Chart 1NO XR25/COMPUTER COMMUNICATION
Lines K and L are shared between several computers, which can disrupt them. If
the fault persists, it would be prudent to check that they are not disrupting lines K
and L.
NOTES
Ensure that the XR25 is not the cause of the fault by trying to communicate with another computer on the
vehicle (air conditioning computer, injection computer ...).
Check that the ISO selector is on position S8 , that you are using the latest XR25 cassette and the correct
access code (D56).
Check the battery voltage (U > 10.5 volts). Recharge the battery if necessary.
Ensure that the diagnostic socket is correctly fed.
Check and ensure the continuity and insulation of the wiring of tracks A3 and A4 of the decoder unit
connector.
If there is still no dialogue between the XR25 and the decoder unit , replace the decoder unit .
Check that the 18 track decoder unit connector is correctly connected.
Check that the decoder unit is correctly fed :
-earth on track A8 of the decoder unit connector
-+ before ignition feed on track A9 of the decoder unit connector.
Check the condition of the +before ignition fuse.
Replace the fuse if necessary.
82-26