1997 RENAULT KANGOO ABS

ENGINE AND ENGINE PERIPHERALS
Engine - Gearbox
10
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect:
- the battery,
- the electrical connectors from the engine
connection unit and its environment.
13034S
Drain:
- the cooling circuit (bottom hose of the
radiator),
- the gearbox oil,
- the engine oil if necessary.
Remove:
- the battery,
- the bonnet,
- the wheels,
- the air intake pipe,
- the expansion bottle and fix it to the engine. Brake caliper guide bolt 4
Shock absorber base bolts 18
Driveshaft gaiter mounting bolt 2.5
Wheel bolt 9
Left-hand suspended mounting bolt
on gearbox 6.2
Left-hand suspended mounting bolt
and nut on body 2.1
Right hand suspended
engine mounting bolt on engine 6.2
Right hand suspended
engine mounting bolt on body 6.2
TIGHTENING TORQUES (in daN.m)
D7F engine
SPECIAL TOOLING REQUIRED
B. Vi. 31-01 Set of three punches for roll
pins
Mot. 1202 Hose clip pliers
Mot. 1273 Tool for checking belt tension
Mot. 1311-06 Tool for removal of fuel pipe
Mot. 1379 Tool for retaining engine on
sub-frame
T. Av. 476 Ball joint extractor
EQUIPMENT REQUIRED
Load positioner
10-4

ENGINE AND ENGINE PERIPHERALS
Engine - Gearbox
Left-hand side of the vehicle
Remove:
- the brake caliper mounting bolt, then fix it to
the shock absorber spring,
- the three driveshaft gaiter mounting bolts,
- the track rod end with the aid of tool
T.Av.476,
- the shock absorber base bolts.
Tilt the hub to disconnect the driveshaft from the
gearbox.
Right-hand side of the vehicle
Remove:
- the driveshaft roll pins with the punches
B.Vi.31-01,
- the brake caliper mounting bolt, then fix it to
the shock absorber spring,
- the track rod end with the aid of tool
T.Av.476,
- the shock absorber base bolts.
Tilt the hub to disconnect the driveshaft from the
gearbox.
Remove the earth strap mounting bolt (gearbox
side)
10D7F engine
10-5

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect:
- the battery,
- the electrical connectors from the engine
connection unit and its environment.
13034S
Drain:
- the cooling circuit (disconnect the bottom
hose of the radiator),
- the gearbox oil if necessary,
- the engine oil if necessary.
Remove:
- the battery,
- the wheels,
- the air intake pipe,
- the upper radiator mountings,
- the expansion bottle and fix it to the engine,
- the power assisted steering fluid reservoir,
and secure it onto the engine. Shock absorber base bolts 18
Track rod end 3.7
Front sub-frame mounting bolt 6.2
Rear sub-frame mounting bolt 10.5
Driveshaft gaiter mounting bolt 2.5
Wheel bolt 9
Mounting nut for rubber engine mounting
pad on left suspended engine mounting 6.2
Mounting bolt for front right suspended
engine mounting on the engine 6.2
Mounting bolt for front right suspended
engine mounting on the body 6.2
Steering shaft yoke bolt 2.5
TIGHTENING TORQUES (in daN.m)
D7F engine
SPECIAL TOOLING REQUIRED
B. Vi. 31-01 Set of punches for roll pins
Mot. 1040-01 Dummy sub-frame for
removing and refitting engine
and transmission assembly
Mot. 1202 Hose clip pliers
Mot. 1311-06 Tool for removal of fuel pipe
Mot. 1379 Tool for retaining engine on
sub-frame
T. Av. 476 Ball joint extractor
T. Av. 1233-01 Tool for sub-frame and axle
assembly
10-9

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
Disconnect:
- the accelerator cable,
- the canister pipe,
- the brake servo pipe,
- the heater hoses,
- the oxygen sensor connector,
- the fuel pipes.
Remove:
- the shock absorber base bolts,
- the steering shaft yoke bolt.
10
97390-1R
SPECIAL NOTES FOR VEHICLES FITTED WITH
DRIVER’S AIR BAG
WARNING
In order to avoid any risk of damage to the rotary
switch beneath the steering wheel, the following
instructions should be followed:
• Before disconnecting the steering column from
the rack, the steering wheel MUST be immobi-
lised with the wheels straight with the aid of a
"steering wheel lock" throughout the opera-
tion.
• If there is any doubt about the rotary switch
being properly centred, the steering wheel
must be removed in order to apply the centring
method described in the Technical Note cove-
ring the 2nd generation air bag.
REMINDER: this kind of work must only be carried
out by properly trained and qualified staff.
Remove:
- both the sub-frame reinforcements,
- the earth strap mounting bolt on the body
side,
- the exhaust downpipe nuts. D7F engine
10-10

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
Front sub-frame mounting bolt 6.2
Rear sub-frame mounting bolt 10.5
Mounting bolt for front right suspended
engine mounting cover on engine 6.2
Mounting nut for front right suspended
engine mounting cover 4.4
Mounting nut for rubber engine mounting pad
on front left-hand side member support 6.2
Shock absorber base bolt 18
Brake caliper mounting bolt 4
Steering shaft yoke bolt 3
Wheel bolt 9
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain:
- the cooling circuit through the bottom hose
of the radiator,
- the gearbox and the engine if necessary.
Remove:
- the bonnet,
- the front wheels,
- the tie-rods between sub-frame and body,- the mounting bolts (1); pull away the brake
calipers as shown in the diagram below and
attach them to the suspension springs,
12994R1
- the shock absorber base bolts, E7J engine
SPECIAL TOOLING REQUIRED
Mot. 1040-01 Dummy sub-frame for removing
and refitting engine and
transmission assembly
Mot. 1159 Tool for maintaining engine on
sub-frame
Mot. 1202
Mot. 1448
Mot. 1311-06 Tool for removing fuel pipe
Hose clip pliers
10-14

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
SPECIAL TOOLING REQUIRED
Mot. 1040-01 Dummy sub-frame for removing -
refitting the engine and
transmission assembly
Mot. 1159 Tool for maintaining engine on
sub-frame
Mot. 1202
Mot. 1448
Mot. 1311-06 Tool for removing fuel pipe
Front sub-frame mounting bolt 6.2
Rear sub-frame mounting bolt 10.5
Mounting bolt for front right suspended engine
mounting cover on engine 6.2
Mounting nut for front right suspended engine
mounting cover 4.4
Mounting nut for rubber engine mounting
pad on front left side member support 6.2
Shock absorber base bolt 18
Brake caliper mounting bolt 4
Steering shaft yoke bolt 3
Wheel bolt 9
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain:
- the cooling circuit through the bottom hose
of the radiator,
- the gearbox and the engine if necessary.
Remove:
- the bonnet,
- the front wheels,
- the tie-rods between sub-frame and body,- the mounting bolts (1); pull away the brake
calipers as shown in the diagram below and
attach them to the suspension springs,
12994R1
- the shock absorber base bolts, F8Q engine
Hose clip pliers
10-19

DIESEL EQUIPMENT
Advance solenoid valve
13
13342R
To remove the terminals from the pump
connector :
1) Pull the yellow guide to release the terminal
connectors, then press on the two tabs on
each side of the connector.
2) Extract the yellow guide.
3) Pull the wire to be removed.
4) The terminal connector is secured by two
tabs, one on each side ; using a screwdriver,
move one of these to one side (the action of
pulling on the wire prevents the tab from
going back into place).
5) Using a screwdriver, move the other tab to
one side.
The terminal connector can now be removed from
the connector.Remove the protective sheath grouping the pump
actuators.
Remove the protective cover from the solenoid
valve.
Remove the solenoid valve using tool Mot. 997-
01.
10579R1
APassage of connector
13-20

DIESEL EQUIPMENT
Altimetric corrector
13
13342R
To remove the terminals for the pump
connector:
1) Pull the yellow guide to release it from the
terminals, then press the two tabs on either
side of the connector.
2) Extract the yellow guide.
3) Pull the wire to be removed.
4) The terminal is held in place by two small tabs,
one on each side; using a screwdriver, move
one of the tabs to one side (the action of
pulling on the wire prevents the tab from
going back into place.
5) Using a screwdriver move the other tab to one
side.
The terminal may now be removed from the
connector.Remove the protective sheath grouping the pump
actuators.
Remove the protective cover from the solenoid
valve.
Remove the altimetric corrector (1) using tool
Mot. 1440.
10579R2
AConnector passage
F8Q 662
13-23