1997 RENAULT KANGOO ABS

ANTIPOLLUTION
Fuel vapour rebreathing
14
OPERATING DIAGRAM OF THE CIRCUIT
1 Inlet manifold
2 Fuel vapour absorber (canister)
3 RCO control solenoid valve
4 Cylinder head
R Pipe from fuel tank
99933R
PRC14.1
D7F Engine
14-2

ANTIPOLLUTION
Fuel vapour rebreathing
14E7J Engine
OPERATING DIAGRAM OF THE CIRCUIT
1 Inlet manifold
2 Fuel vapour absorber (canister)
3 RCO control solenoid
4 Throttle body
R Pipe from fuel tank
13123R
14-3

ANTIPOLLUTION
Fuel vapour rebreathing
14
LOCATION-REMOVAL OF COMPONENTS
CANISTER BLEED SOLENOID VALVE
(1)
E7J Engine
It is mounted above the inlet manifold,
underneath the cover
D7F Engine
It is mounted at the front, on the lifting bracket.
13242R2
99939-1R3
REMOVAL OF THE FUEL VAPOUR ABSORBER (1)
This is located in the front right hand wheel arch.
REMOVAL
Disconnect the pipe connecting the canister to the
inlet manifold, from the top of the vehicle.
From the bottom, remove the wheel arch .
Disconnect the pipe at (2) connecting the
canister to the fuel tank.
Remove the three bolts at (3) mounting the
canister (1) then extract it.
13049R
14-6

STARTING - CHARGING
Starter motor
16
OPTIMA 5800 Diagnostic station
CHECKING THE STARTER MOTOR USING THE DIAGNOSTIC STATION
Checking of the starter motor is carried out using the OPTIMA 5800, by measuring the battery voltage and
the current absorbed in the engine starting phase. The following operation faults may be highlighted :
- a fault in the battery ( the voltage falls during the starting phase),
- locking of the starter motor (the current absorbed is too high),
- a fault in the engine starter gear (the current absorbed is too low).
In order to carry out the measurement, it is necessary to stop the vehicle from starting :
- for D7F and E7J engines : disconnect the engine speed sensor (located on the clutch housing ,
- for
F8Q engines : disconnect the pump electrical solenoid and isolate the terminal.
NOTE :
- an open circuit on the engine speed sensor or the ignition creates a fault memorised by the injection
computer, this fault must then be erased from the memory using the
XR25 (see "Injection" section),
- if the engine is fitted with an immobiliser, it is sufficient to lock the doors using the remote control.
FAULT FINDING
SPECIAL TOOLING REQUIRED
16-8

STARTING - CHARGING
Starter motor
16
REMOVAL
Place the vehicle on a two post lift.
Remove :
- the battery,
- the injection computer mounting, after ha-
ving disconnected the 55 track connector as
well as the impact switch connector,
13088S
- the mounting (1) for the power assisted stee-
ring pipe, along with the strut at (A),
13336-1R
- the front right hand wheel ,
- the driveshaft pin using punches B. Vi. 31-01,
- the upper shock absorber bolt and slacken the
lower bolt.
Tilt the hub and release the driveshaft assembly
from the gearbox.
Remove the starter connections , as well as the
mounting bolts and extract these from the bot-
tom of the vehicle.
REFITTING
Refitting is the reverse of removal.
Check for the presence of the centring dowel
which should be located at (B).
13087R
E7J Engine
16-10

INJECTION
General
17
1 Coil
2 Air filter
3 Oxygen sensor
4 Absolute pressure sensor
5 Throttle position potentiometer
6 Idle regulation stepping motor
7 Air temperature sensor
8 Injection computer
9 Inertia switch
10 Locking relay
11 Fuel pump relay
12 TDC sensor
13 Fuel vapour recycling solenoid valve
14 Coolant temperature sensor
15 Tool for removing spark plug leads
16 Pinking sensor
17 Power assisted steering pressostat
18 Pressure regulator
19 Anti-interference condenser
20 Fuel vapour absorber (canister)
LOCATION OF COMPONENTS
13081
D7F Engine
17-6

INJECTION
General
17
1 Fuel vapour recycling solenoid valve
2 Air filter
3 Pinking sensor
4 Absolute pressure sensor
5 Idle speed regulation stepping motor
6 Throttle position potentiometer
7 Air temperature sensor
8 Injection computer
9 Inertia switch
10 Fuel pump relay
11 TDC sensor
12 Coolant temperature sensor
13 Oxygen sensor
14 Coil for cylinders 2 - 3
15 Power assisted steering pressostat
16 Coil for cylinders 1 - 4
17 Fuel vapour absorber (canister)
18 Anti-interference condenser
LOCATION OF COMPONENTS
13082
E7J Engine
17-7

INJECTION
Location of components
17
4 Absolute pressure sensor
5 Throttle position potentiometer
6 Idle speed regulation stepping motor
7 Air temperature sensor13 Fuel vapour recycling solenoid
14 Coolant temperature sensor 16 Pinking sensor
(tightening torque: 2.5 daN.m)
11313R4
11311R1
99939-1R2
8 Injection computer
9 Inertia switch
13051R1
D7F Engine
17-8