1997 PONTIAC FIREBIRD air condition

If you do not have traction control, or if the system is
off, then an acceleration skid is also best handled by
easing your foot off the accelerator pedal.
If your vehicle starts to slide, ease your foot off the
accelerator pedal and quickly steer the way you want the
vehicle to go. If you start steering quickly enough, your
vehicle may straighten out. Always be ready for a
second skid
if it occurs.
Of course, traction is reduced when water, snow, ice,
gravel or other material is on the road. For safety, you’ll
want to slow down and adjust your driving to these
conditions. It
is important to slow down on slippery
surfaces because stopping distance will be longer and
vehicle control more limited.
While driving on a surface with reduced traction, try
your best to avoid sudden steering, acceleration
or
braking (including engine braking by shifting to a
lower gear). Any sudden changes could cause the tires
to slide.
You may not realize the surface is slippery until
your vehicle is skidding. Learn to recognize warning
clues
-- such as enough water, ice or packed snow on
the road to make a “mirrored surface” -- and slow down
when you have any doubt.
Remember: Any anti-lock brake system
(ABS) helps
avoid only the braking skid.
Driving at Night
I
.A
Night driving is more dangerous than day driving.
One reason is that some drivers are likely
to be
impaired -- by alcohol or drugs, with night vision
problems, or by fatigue.
4-15

If No Steam Is Coming From Your Engine
If you get the overheat warning but see or hear no
steam, the problem may not be too serious. Sometimes
the engine can get a little too hot when you:
Climb a long hill on a hot day.
Stop after high-speed driving.
Idle for long periods in traffic.
Tow a trailer.
If you get the overheat warning with no sign of steam,
try this for a minute or
so:
1. If you have an air conditioner, turn it off.
2. Turn on your heater to full hot at the highest fan
speed and open the window as necessary.
3. If you’re in a traffic jam, shift to NEUTRAL (N);
otherwise, shift to the highest gear while
driving
-- AUTOMATIC OVERDRIVE (@) or
DRIVE (D) for automatic transmissions.
If you no longer have the overheat warning, you can
drive. Just to be safe, drive slower for about
10 minutes.
If the warning doesn’t come back on, you can
drive normally.
If the warning continues, pull over, stop, and park your
vehicle right away.
If there’s still no sign of steam, you can idle the engine
for two or three minutes while you’re parked, to see if
the warning stops. But then, if
you still have the
warning,
turn ofSthe engine and get everyone out of the
vehicle until it cools down.
You may decide not to lift the hood but to get service
help right away.
When you decide it’s safe to lift the hood, here’s what
you’ll see:

At a minimum, the gasoline you use should meet
specifications
ASTM D4814 in the United States and
CGSB 3.5-M93 in Canada. Improved gasoline
specifications have been developed by the American
Automobile Manufacturers Association
(AAMA) for
better vehicle performance and engine protection.
Gasolines meeting the AAMA specification could
provide improved driveability and emission control
system protection compared to other gasolines,
Be sure the posted octane for premium is at least
91 (at least 89 for middle grade and 87 for regular).
If the octane is less than
87, you may get a heavy
knocking noise when
you drive. If it’s bad enough,
it can damage your engine.
If you’re using fuel rated at the recommended octane
or higher and you still hear heavy knocking, your
engine needs service.
But dm9t worry if you hear a little
pinging noise when you’re accelerating
or driving up a
hill. That’s normal, and you don’t have
to buy a higher
octane fuel
to get rid of pinging. It’s the heavy, constant
knock that means you have
a problem. If
your vehicle is certified
to meet California Emission
Standards (indicated on the underhood tune-up label), it
is designed to operate on fuels that meet California
specifications. If such fuels are
not available in states
adopting California emissions standards, your vehicle
will operate satisfactorily
on fuels meeting federal
specifications, b’ut emission control system performance
may be affected. The malfunction indicator lamp
on
your instrument panel may turn on and/or your vehicle
may fail
a smog-check test. If this occurs, return to your
authorized Pontiac dealer for diagnosis to determine
the
cause of failure. In the event it is determined that the
cause of the condition is the type of fuels used, repairs
may not be covered by your warranty.
Some gasolines that
are not reformulated for low
emissions contain
an sctane-enhancing additive called
methylcyclopentadienyl manganese tricarbonyl (MMT);
ask your service station operator whether or not his fuel
contains
MMT. General Motors does not recommend the
use of such gasolines. If fuels containing MMT are used,
spark plug life may be reduced and your emission
control system performance may
be affected. The
malfunction indicator lamp on your instrument panel
may turn
on. If this occurs, return to your authorized
Pontiac dealer for service.
6-4

1 Vf a I IJ
If you have the 5.7L LT1 engine (with the WS6 option),
your air cleaner will be located over the radiator near the
front
of the engine.
To remove the filter, remove the screws (located on the
rear edge of the air cleaner), lift the air cleaner and
remove
the filter.
Automatic Transmission Fluid
When to Check and Change
A good time to check your automatic transmission fluid
level is when the engine oil is changed.
Change both the fluid and filter every 15,000 miles
(25 000 km) if the vehicle is mainly driven under one
or more of these conditions:
In heavy city traffic where the outside temperature
0 In hilly or mountainous terrain.
regularly reaches
90” F (32” C) or higher.
0 Uses such as high
performance operation.
When doing frequent trailer towing.
Uses such as found in taxi, police or delivery service.
If you do
not use your vehicle under any of these
conditions, change the fluid and filter every
100,000 miles ( 166 000 km),
See “Scheduled Maintenance Services” in the Index.
6-22

Brake linings should always be replaced as complete
See
“Brake System Inspection” in Section 7 of this
NOTICE: axle sets.
Continuing to drive with worn-out brake pads
Inspections”. could result in costly brake repair.
manual under Part C “Periodic Maintenance
Same driving conditions or climates may cause a brake
squeal when the brakes are. first applied or lightly
applied. This does not mean something is wrong with
your brakes.
See “Caliper/Knuckle Maintenance Inspection’’ in
Section
7 of this manual under Part C “Periodic
Maintenance Inspections.”
If you have rear drum brakes, they don’t have wear
indicators, but
if you ever hear a rear brake rubbing
noise, have the rear brake linings inspected. Also, the
rear brake drums should
be removed and inspected each
time the tires are removed for rotation or changing.
When
you have the front brakes replaced, have the rear
brakes inspected, too.
Brake Pedal Travel
See your dealer if the brake pedal does not return to
normal height, or if there is a rapid increase in pedal
travel.
This could be a sign of brake trouble.
Brake Adjustment
Every time you make a moderate brake stop, your disc
brakes adjust for wear.
If you rarely make a moderate or
heavier stop, then your brakes might not adjust correctly.
If you drive in that way, then -- very carefully -- make
a few moderate brake stops about every 1,000 miles
(1 600 km), so your brakes will adjust properly.
If your brake pedal goes down farther than normal, your
rear drum brakes may need adjustment. Adjust them by
backing up and firmly applying the brakes
a few times.
6-39

Wheel Replacement
Replace any wheel that is bent, cracked, or badly rusted
or corroded. If wheel nuts keep coming loose, the wheel,
wheel bolts and wheel nuts should be replaced.
If the
wheel leaks air, replace
it (except some aluminum
wheels, which can sometimes be repaired). See your
Pontiac dealer if any
of these conditions exist.
Your dealer will know the kind
of wheel you need.
Each new
wheel should have the same load-carrying
capacity, diameter, width, offset and be mounted the
same way as the one it replaces.
If you need to replace any of your wheels, wheel
bolts or wheel nuts, replace them only with new
CM
original equipment parts. This way, you will be sure to
have the right wheel, wheel. bolts and wheel nuts
for
your Pontiac model.
Using the wrong replacement wheels, wheel bolts
or wheel nuts on your vehicle can be dangerous.
It could affect the braking and handling of your
vehicle, make your tires
lose air and make you
lose control. You could have a collision in which
you or others could be injured.
Always use the
correct wheel, wheel bolts and wheel nuts
for
replacement.
NOTICE:
~
The wrong wheel can also cause problems with
bearing life, brake cooling, speedometer or
odometer calibration, headlamp aim, bumper
height, vehicle ground clearance
and tire or tire
chain clearance to the body and chassis.
See “Changing a Flat Tire” in the Index for more
information.
6-56

Underbody Maintenance
Chemicals used for ice and snow removal and dust
control can collect on the underbody. If these are not
removed, accelerated corrosion (rust) can occur on the
underbody parts
such as fuel lines, frame, floor pan and
exhaust system even though they have corrosion
protection.
At least every spring, flush these materials from the
underbody with plain water. Clean any areas where mud
and other debris can collect. Dirt packed in closed areas
of the frame should be loosened before being flushed.
Your dealer or an underbody car washing system can do
this for you.
Chenf ea1 Paint Spotting
Some weather and atmospheric conditions can create a
chemical fallout, Airborne pollutants can fall upon and
attack painted surfaces on your vehicle. This damage
can take two forms: blotchy, ringlet-shaped
discolorations,
and ,mall irregular .dark spots etched into
the paint surface.
Although no defect in the paint
job causes this, Pontiac
will repair, at
no charge to the owner, the surfaces of
new vehicles damaged by this fallout condition within
12 months or 12,000 miles (20 000 km) of purchase,
whichever occurs first.
6-66

Underhood Electrical Center
Fuse
ABS IGN (SA)
ACTUATORS (15A)
R HDLP DR (154
L HDLP DR (1 5A)
ABS VLV (20A)
Usage
Anti-Lock Brake System
Daytime Running
Lamp
Module, Headlamp
Switch, Cooling Fan
Relay, Exhaust,
Gas
Recirculation, EVAP
Canister Purge Solenoid
Headlamp Door Module
Headlamp
Door Module
Brake Pressure Valve
Fuse
ABS BAT (5A)
HORN (20A)
INJECTOR (15A)
ENG SEN (20A)
IGNITION
(1OA)
Usage
Electronic Brake Control
Module
AIR PUMPFAN
(25A) AIR Pump (V8) Relay,
Pump, Bleed Valve
and Cooling Fan
Horn Relay
Fuel Injectors
Mass Airflow, Heated
Oxygen
Sensor, Reverse
Lockout Solenoid, Skip
Shift Solenoid, Automatic
Transmission, Brake Switch
V6 VIN K: Electronic
Ignition Module
VS
VIN P: Ignition Coil
Module, Crankshaft
Position
Sensor.
A/C-CRUISE (15A) Air Conditioning
Compressor Relay;
Cruise Control Switches
and Module
6-72