1997 Oldsmobile Aurora light

Time Out Feature Theater Dimming
The interior
lamps will automatically shut off after 10
minutes if a door is left open. This feature is designed to
help eliminate battery wear down.
Courtesy Lamps
When any door is opened, several lamps go on. They
make it easy for you to enter and leave the car. To turn
on these lamps, rotate the
INTERIOR LIGHTS knob all
the way to
HI.
Delayed Illumination
When you open the door to enter your vehicle, the interior
lamps will come on. When you close the door with the
ignition
off, the interior lamps will stay on for 25 seconds
or until the ignition is turned on. Please note that locking
the doors will override the delayed illumination feature
and the lights will turn off right away. This feature allows for
a three to five-second fade out
of
the courtesy lamps instead of immediate turn off. They
will not fade if the interior lights switch
is used.
Parade Dimming
This feature prohibits the dimming of your instrument
displays during daylight while your headlamps are on.
This feature operates with the light sensor for
the
twilight sentinel and is fully automatic. When the light
sensor reads darkness outside, you will be able to dim
your instrument panel displays once again.
Exit Lighting
With this feature, the interior lamps will come on for
25 seconds after you remove the key from the ignition.
This will give you time to find the door pull handle or
lock switches when you exit the vehicle.
2-47

Illuminated Entry
Press the UNLOCK button on the key chain transmitter
and the interior courtesy lamps will come on and stay on
for up
to a minute. The lamps will turn off immediately
by pressing the
LOCK button on the key chain
transmitter, starting the ignition or activating the power
door locks.
Perimeter Lighting
When the UNLOCK button on the key chain transmitter
is pressed, the headlamps, parking lamps, back-up
lamps and cornering lamps will come on if it is dark
enough outside according to the twilight sentinel.
This option can be programmed on or off for
each transmitter.
To turn the feature off
1. Press and hold the door lock switch throughout this
procedure. All doors will lock.
2. Press the instant alarm button on the transmitter.
Perimeter lighting remains on at this time and the
horn will chirp two times.
3. Press the instant alarm button on the key chain
transmitter again. Perimeter lighting is disabled and
the horn will chirp one time.
4. Release the door lock switch. The perimeter lighting
option is now
off.
2-48

To turn the feature on: Front Reading Lamps
1.
2.
3.
4.
Press and hold the door lock switch throughout this
procedure. All doors will lock.
Press the instant alarm button
on the key chain
transmitter. Perimeter lighting remains off at this
time and the
horn will chirp one time.
Press the instant alarm button on the transmitter
again. Perimeter lighting is now enabled and the
horn will chirp two times.
Release the door lock switch. The perimeter lighting
option is now on.
These lamps and the interior courtesy lamps will come
on when you open a door. They will turn off when you
turn on
the ignition. If the door is left open, they will
turn off after about
10 minutes.
To turn
on the reading lamps when the doors are closed,
press the button behind the lamp you want on. Press
it
again to turn the lamp off.
These lamps work even when the ignition is off. To avoid
draining your vehicle's battery, be sure to
turn off all front
and rear reading lamps when leaving your vehicle.
2-49

Setting the Mirror Time Delay
OFF: This
setting turns off the day/night function and
compass. The mirror will stay in the day mode.
M: This turns on the day/night portion of the mirror to
automatically reduce glare.
C/M: This setting turns on the compass in addition to
the day/night function. The letter or letters displayed in
the top right corner
of the mirror indicate the direction
in which you are traveling. This mirror
has a time delay feature that prevents rapid
changing from the night mode
to the day mode as you
drive under lights and through traffic.
Reverse Gear Day Mode
The reverse mode is another important feature of
the electrochromic mirror. When you shift into
REVERSE (R), the mirror changes to the day mode.
This gives you a bright image in the mirror as you
back up.
Cleaning the Photocells
Use a cotton swab and glass cleaner to clean the
photocells when necessary.
2-

Convenience Net
l Your vehicle has a convenience net just inside the back 1 wall of the trunk.
Put small loads, like grocery bags, behind the net. It can
help keep them from falling over during sharp
turns or
quick starts and stops.
The net isn’t for larger, heavier loads. Store them in the
trunk as far forward as you can. You can unhook the net
so that it will lie flat when you’re not using it.
Two positions exist for the convenience net, depending
on the size of the cargo.
Use this position for slightly larger loads.
When installing the net in either position, be sure the
“up label”
(A) is pointing up.
Use
this position for small loads.
2-56

Ashtrays and Cigarette Lighter
Push and release the cover to reveal the front ashtray,
lighter and accessory power outlet.
I NOTICE:
Don’t put papers and other things that burn into
your ashtrays. If you do, cigarettes
or other
smoking materials could set them on fire,
causing damage.
To open either rear ashtray, you may press and release
the cover or pull up the cover lid.
To clean an ashtray, make sure the cover is open fully,
then lift out the ashtray by pulling on the snuffer.
To use a lighter, just push it in all the way and let go.
When it’s ready, it will pop back by itself.
NOTICE:
Don’t hold a cigarette lighter in with your hand
while it
is heating. If you do, it won’t be able to
back away from the heating element when it’s
ready. That can make it overheat, damaging the
lighter and the heating element.

Universal Transmitter This device complies with Part 15 of the FCC Rules.
Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-210 of Industry and
Science Canada. Operation is subject to the following
two conditions:
(1) this device may not cause
interference, and
(2) this device must accept any
interference, including interference that may cause
undesired operation of the device.
Changes or modifications to this system by other than an
authorized service facility could void authorization to
use this equipment.
Programming the Transmitter
Do not use the universal transmitter with any garage
door opener that does not have the “stop and reverse”
safety feature. This includes any garage door opener
model manufactured before April
1, 1982.
Be sure that people and objects are clear of the garage
door
you are programming.
This transmitter allows
you to consolidate the functions
of up to three individual hand-held transmitters. It will
operate garage doors and gates, or other devices
controlled
by radio frequency such as home and office
lighting systems.
The transmitter will learn and transmit the frequencies
of most current transmitters and is powered by your
vehicle’s battery and charging system.

Your vehicle’s engine should be turned off while
programming your transmitter. Follow these steps to
program up to three channels:
1.
2.
3.
4.
- -
If you have not previously programmed a universal
transmitter channel, proceed to Step
2. Otherwise,
hold down the two outside buttons on the universal
transmitter until the red light begins to flash rapidly
(approximately
20 seconds). Then release the
buttons. This procedure initializes the memory and
erases any previous settings for all three channels.
Hold the end
of your hand-held transmitter against
the bottom surface of the universal transmitter
so
that you can still see the red light.
Decide which one of the three channels you want to
program. Using both hands, press the hand-held
transmitter button and the desired button on the
universal transmitter. Continue to hold both buttons
through Step
4.
Hold down both buttons until you see the red light
on the universal transmitter flash slowly then rapidly.
The rapid flashing, which could take up to
90 seconds, indicates that the universal transmitter
has been programmed. Release both buttons three
seconds after the light starts
to flash rapidly. If
you have trouble programming the universal
transmitter, make sure that you have followed the
directions exactly
as described and that the batteries in
the hand-held transmitter are not dead. If you still
cannot program it, rotate your hand-held transmitter end
over end and try again. The universal transmitter may
not work with older garage door openers that do not
meet current Federal Consumer Safety Standards. If you
cannot program the transmitter after repeated attempts,
consult your Aurora retailer.
Be sure to keep your original hand-held transmitter in case
you need to erase and reprogram the universal transmitter.
Note to Canadian Owners: During programming, your
hand-held transmitter may stop transmitting after one or
two seconds. If you are programming from
one of these
transmitters, you should press and re-press the button on
the hand-held transmitter every two seconds without
ever releasing
the button on the universal transmitter.
Release both buttons three seconds after the red light on
the universal transmitter begins to flash rapidly.
Operating the Transmitter
Press and hold the appropriate button on the universal
transmitter. The red light comes on while the signal
is
being transmitted.
Note that the effective transmission range
of the
universal transmitter may differ from your hand-held
transmitter and also from one channel to another.
2-62