1997 Oldsmobile Aurora lock

2. Release tension of the wing screw clamp on the air
intake duct where it attaches to the air cleaner cover
near the top of the engine.
Turn the wing screw
counterclockwise, then detach the hose
from the air
cleaner cover.
3. To remove the air cleaner cover, push the duct and
resonator assembly rearward and up, and hold them
out
of the way.
cover and tube.
4. Reverse the instructions to replace the air cleaner
Low-Beam Headlamp Bulbs
If you need to replace a headlamp bulb, do
the following:
1. Remove the two bolts and pull out the headlamp
assembly for more hand clearance.
2. Twist the bulb assembly one-sixth of a turn
counterclockwise and pull out the bulb assembly.
6-35

3.
II II
Unclip the bulb
assembly from the
wiring harness and replace the
bulb assembly.
4. Reverse Steps 1 through 4 to replace the bulb
assembly, headlamp housing, air cleaner cover
and tube.
5. Replace the headlamp assembly by aligning the pin
and tightening the two bolts to secure it.
High-Beam Headlamp Bulbs
If you need to replace a headlamp bulb, do the following:
1. Remove the headlap assembly if you need more
hand clearance.
2. Pull up on the wiring harness. This unlocks the bulb.
- v-
3. Now you can reach in behind the lamp housing and
4. To replace the bulb, angle the new bulb into the
pull out
the bulb.
empty socket.
5. Push the base of the bulb down to lock it into place.
6. If you removed the headlamp assembly, reassemble
it by aligning the pin and tightening the two bolts to
secure it.

Front Turn Signal
The turn signal bulb is on the inboard edge of the
headlamp assembly.
To replace a bulb, do the following:
1.
2.
3.
4.
Remove the headlamp assembly if you need more
hand clearance.
Reach in and press the locking tab while twisting the
bulb assembly one-quarter of a turn
counterclockwise.
Replace the bulb and reverse Step
2 to reassemble.
If you removed the headlamp assembly, reassemble
it by aligning the pin and tightening the two bolts to
secure
it.
Headlamp Aiming
Your vehicle has the composite headlamp system. These
headlamps have horizontal and vertical aim indicators.
The aim has been pre-set at the factory and should need
no further adjustment.
If your vehicle is damaged in an accident and the
headlamp aim seems
to be affected, see your Aurora
retailer. Headlamps on damaged vehicles may require
recalibration
of the horizontal aim by your Aurora retailer.
To check the aim, the vehicle should be properly
prepared as
follows:
e
0
e
The vehicle must have all four tires on a perfectly
level surface.
The vehicle should not have
any snow, ice or mud
attached to it.
There should not be any cargo or loading of the
vehicle, except it should have a full tank
of gas and
one person or
160 lbs. (75 kg) on the driver’s seat.
Tires should be properly inflated.
I NOTICE:
To make sure your headlamps are aimed
properly, read all the instructions before
beginning. Failure to
follow these instructions
could cause damage to headlamp parts.
State inspection stations will allow a vertical reading of
plus
0.76 degrees or minus 0.76 degrees from the center
of the bubble.
It is recommended that the upper limit not exceed plus
0.4 degrees from the center of the bubble. Other drivers
may flash their high beams at
you if your adjustment is
much above plus
0.4 degrees.
6-37

2. Use a 10 mm socket to
remove the four bolts.
There
are two bolts on
each side of the cover.
3. Pry off the cover and pull down to access the bulbs.
4. Press the locking tab of the bulb assembly.
6-42

5. Twist the socket one-quarter of a turn
counterclockwise and pull to remove.
6. Replace the bulb and reverse Steps 1 through 4 to
replace the assembly and tighten the bolts.
Interior Lamps
Front and Rear Reading Lamps
To change the bulbs in the front and rear reading lamps,
do the following:
1. Carefully insert a flat head screwdriver in the slot
between
the lens cover and molding.
2. Gently pry the lens cover away to expose the reading
lamp bulb. The lens cover should pop off.
new bulb.
3. Remove the bulb from its assembly and install a
4. Snap the lens cover back in place.

Maxifuse/Relay Center
It’s easy to check the fuses in this underhood relay
center. There are two locking arms on either side
of the
base of the cover. Reach down and unsnap each one by
pulling
the cover toward you, then pushing it away
while pulling up. Remove the cover.
The inside of the
cover has a chart that explains the features and controls
governed by each fuse and relay.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits
by a combination of fuses and circuit
breakers. This greatly reduces the chance of damage
caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse. Be sure
you replace a bad fuse with a new one of the correct
amp rating.
Two spare fuses are located below the fuse puller.
You’ll
also find spare fuses in the slots labeled “Spare” in the
following charts.
There are three main fuse panels: the instrument panel
fuse block and two (driver’s side and passenger’s side)
rear compartment fuse blocks.
Instrument Panel Fuse Block
This is located on the left side of the instrument panel.
To open it, push the latch to the left, then pull, and the
door will open.
You’ll find a fuse puller clipped to the inside of the
cover. Place the wide end of the fuse puller over the
plastic end
of the fuse. Squeeze the ends over the fuse
and pull
it out. To close the fuse door, press the door
closed and it will latch.

/ INSTRUMENT PANEL
FUSE BLOCK
I1 I 12
I
1 l7 DIS
21 HVAC
RELAY
OXYGEN
LAMPS
J
Fuse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Usage
Supplemental Inflatable Restraint
(Air Bag)
Injectors
Anti-Lock Brake System
Left Exterior Lamps
Turn Signal Lamps
Injectors Climate Controls
Right Exterior Lamps
Chime (Ignition
l), Memory Set
Powertrain Control Module,
VATS
, PASS-Key@II Auxiliary Power
Interior Lamps
Shift Sols
Linear EGR
Cruise Control
Perimeter Lights
6-64

1. Buckle the center passenger position safety belt, and
then route the safety belts through the proper
slots in
the seat cushion. Don’t let the safety belt get twisted.
2. Slide the rear of the cushion up and under the
seatback
so the rear locating guides hook into the
wire loops
on the back frame.
3. With the seat cushion lowered, push rearward and
then press down on the seat cushion until the spring
locks on both ends engage.
4. Check to make sure the safety belts are properly
routed and that no portion
of any safety belt is
trapped under the seat.
Also make sure the seat
cushion
is secured.
Rear Compartment Fuse Blocks
V“
7- ?
d
Once the seat is removed,
you’ll find two fuse panels
on the driver’s side
of the
battery. Each is protected by
a plastic box with four tabs.
Pull
up on all four tabs at
the same time to loosen
them and pull off the box.
Of these two panels, the cover on the passenger’s side
fuse panel has an extra plastic cap attachment. You’ll
need to slide this out of the grooves which hold it there
before removing the rest
of the box.
To replace the covers, line the four tabs up and simply
snap them back into place. The extra plastic cap
attachment slides back into place.
6-67