ENGINE <4G6> ± General Information/Service Specifications11A-3
GENERAL INFORMATION11100010322
Items4G634G64
Total displacement m1,9972,351
Bore y Stroke mm85.0 x 88.086.5 x 100.0
Compression ratio9.59.5
Combustion chamberPentroof typePentroof type
Camshaft arrangementSOHCSOHC
Number of valve
Intake88
Number of valve
Exhaust88
Intake
OpeningBTDC 11BTDC 18
Valve timing
Intake
ClosingABDC 53ABDC 58
Valve timing
Exhaust
OpeningBBDC 63BBDC 58
Exhaust
ClosingATDC 21ATDC 18
Fuel system
Electronic control
multipoint fuel
injectionElectronic control
multipoint fuel
injection
Rocker armRoller typeRoller type
Auto-lash adjusterEquippedEquipped
SERVICE SPECIFICATIONS11100030342
ItemsStandard valueLimit
Alternator drive
belt
Tension NWhen checked294 ± 490±
belt
tension
When a used belt is installed343 ± 441±
When a new belt is installed490 ± 686±
Deflection
(Reference
When checked7.0 ± 9.0±
(Reference
value) mmWhen a used belt is installed7.5 ± 8.5±
When a new belt is installed5.5 ± 7.5±
Power steering
oilpumpdrive
Tension NWhen checked294 ± 490±
oil um drive
belt tensionWhen a used belt is installed343 ± 441±
When a new belt is installed490 ± 686±
Deflection
(Reference
When checked5.5 ± 7.5±
(Reference
value) mmWhen a used belt is installed6.0 ± 7.0±
When a new belt is installed4.0 ± 6.0±
ENGINE <4D5> ± General Information11B-2
GENERAL INFORMATION11100010339
Items4D56
Total displacement m2,477
Bore x Stroke mm91.1 x 95.0
Compression ratio21
Combustion chamberVortex chamber type
Camshaft arrangementSOHC
Number of valveIntake4
Exhaust4
Valve timingIntakeOpening BTDC 20, Closing ABDC 49
ExhaustOpening BBDC 55, Closing ATDC 22
Fuel systemDistribution type injection pump
Rocker armRoller type
Adjusting screwElephant foot type
ENGINE LUBRICATION ± General Information12-2
GENERAL INFORMATION12100010053
The lubrication method is a fully force-fed, full-flow
filtration type.The corrugate fin type of engine oil cooler have
been adopted, and installed forward of the radiator.
<4D56>
Items4G634G644D56
Oil pump typeInvolute gear typeInvolute gear typeTrochoid type
Drive methodTiming beltTiming beltCrankshaft
ENGINE OILS
Health Warning
Prolonged and repeated contact with mineral oil
will result in the removal of natural fats from the
skin, leading to dryness, irritation and dermatitis.
In addition, used engine oil contains potentiallyharmful contaminants which may cause skin cancer.
Adequate means of skin protection and washing
facilities must be provided.
Recommended Precautions
The most effective precaution is to adapt working
practices which prevent, as far as practicable, the
risk of skin contact with mineral oils, for example
by using enclosed systems for handling used engine
oil and by degreasing components, where
practicable, before handling them.
Other precautions:
Avoid prolonged and repeated contact with oils,
particularly used engine oils.
Wear protective clothing, including impervious
gloves where practicable.
Avoid contaminating clothes, particularly
underpants, with oil.
Do not put oily rags in pockets, the use of
overalls without pockets will avoid this.
Do not wear heavily soiled clothing and
oil-impregnated foot-wear. Overalls must be
cleaned regularly and kept separate from
personal clothing.Where there is a risk of eye contact, eye
protection should be worn, for example,
chemical goggles or face shields; in addition
an eye wash facility should be provided.
Obtain First Aid treatment immediately for open
cuts and wounds.
Wash regularly with soap and water to ensure
all oil is removed, especially before meals (skin
cleansers and nail brushes will help). After
cleaning, the application of preparations
containing lanolin to replace the natural skin
oils is advised.
Do not use petrol, kerosine, diesel fuel, gas
oil, thinners or solvents for cleaning skin.
Use barrier creams, applying them before each
work period, to help the removal of oil from
the skin after work.
If skin disorders develop, obtain medical advice
without delay.
MPI ± General Information13A-4
OTHER CONTROL FUNCTIONS
1. Fuel Pump Control
Turns the fuel pump relay ON so that current
is supplied to the fuel pump while the engine
is cranking or running.
2. A/C Relay Control
Turns the compressor clutch of the A/C
ON and OFF.3. Purge Control Solenoid Valve Control
Refer to GROUP 17.
4. EGR Control Solenoid Valve Control
Refer to GROUP 17.
GENERAL SPECIFICATIONS
ItemsSpecifications
Throttle bodyThrottle bore mm54
Throttle position sensorVariable resistor type
Idle speed control servoStepper motor type
(Stepper motor type by-pass air control system with the air
volume limiter)
Idle position switchRotary contact type, within throttle position sensor
Engine-ECUIdentification model No.E2T64271 <4G63 - Vehicles without immobilizer system>
E2T64277 <4G63 - Vehicles with immobilizer system>
E2T64272 <4G64 - Vehicles without immobilizer system>
E2T64276 <4G64 - Vehicles with immobilizer system>
SensorsAir flow sensorKarman vortex type
Barometric pressure sensorSemiconductor type
Intake air temperature sensorThermistor type
Engine coolant temperature sensorThermistor type
Oxygen sensorZirconia type
Vehicle speed sensorMagnetic resistive element type
Top dead centre sensorHall element type
Crank angle sensorHall element type
Power steering fluid pressure switchContact switch type
ActuatorsControl relay typeContact switch type
Fuel pump relay typeContact switch type
Injector type and numberElectromagnetic type, 4
Injector identification markCDH275
EGR control solenoid valveDuty cycle type solenoid valve
Purge control solenoid valveON/OFF type solenoid valve
Fuel pressure
regulatorRegulator pressure kPa328
MPI ± Troubleshooting13A-47
INSPECTION PROCEDURE 34
MUT-II: Inspection of no initial combustion
MUT-II Data list
16 Voltage of engine-ECU power source (Refer to P.13A-57.)NGCheck the power supply and ignition switch-IG system.
(Refer to P.13A-39, INSPECTION PROCEDURE 23.)
OK
Does the camshaft rotate at the engine cranking?
(When oil filler cap is removed.)NoCheck timing belt for breakage.
Ye s
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13A-10, INSPECTION CHART FOR DIAGNOSIS
CODES.
No
MUT-II Data list
22 Crank angle sensor
OK:Cranking speed is displayed.NoCheck the crank angle sensor system.
(Refer to P.13A-15, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 22.)
OK
MUT-II Actuator test
07 Fuel pump (Refer to P.13A-62.)NGCheck the fuel pump system.
(Refer to P.13A-40, INSPECTION PROCEDURE 24.)
OK
MUT-II Data list
21 Engine coolant temperature sensor (Refer to P.13A-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13A-14, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
INSPECTION PROCEDURE 35
Ignition system: Inspection of no initial combustion.
Does the engine tachometer display the cranking speed?
Set the tachometer of primary voltage detection type.NGCheck ignition circuit system.
(Refer to P.13A-44, INSPECTION PROCEDURE 30.)
OK
Check the ignition timing when cranking.
OK:Approx. 5BTDCNGCheck that the crank angle sensor is installed properly.
± Emission Control System
EMISSION CONTROL17-6
EMISSION CONTROL SYSTEM
GENERAL INFORMATION
The emission control system consists of the following subsystems:
Crankcase emission control system
Evaporative emission control system
Exhaust emission control system
ItemsNameSpecification
Crankcase emission
control systemPositive crankcase ventilation (PCV) valveVariable flow type
(Purpose: HC reduction)
Evaporative emission
control systemCanister
Purge control solenoid valveEquipped
ON/OFF type solenoid valve
(Purpose: HC reduction)
Exhaust emission
control systemAir-fuel ratio control device±MPI systemOxygen sensor feedback type
(Purpose: CO, HC, NOx reduction)
Exhaust gas recirculation system
EGR valve
EGR control solenoid valveEquipped
Single type
Duty cycle type solenoid valve
(Purpose: NOx reduction)
Catalytic converterMonolith type
(Purpose: CO, HC, NOx reduction)
EMISSION CONTROL DEVICE REFERENCE TABLE
Related partsCrankcase
emission
control
systemEvaporative
emission
control
systemAir/fuel
ratio
control
systemCatalytic
converterExhaust
gas
recircula-
tion systemReference
page
PCV valvey17-
Purge control solenoid valvey17-
MPI system componentyyGROUP 13A
Catalytic convertery17-
EGR valvey17-
EGR control solenoid valvey17-