1997 Mercury Villager stop start

38
[AS11200(ALL)05/94]3.
Using the ªSEEKº function with a cassette tape
[AS11300(ALL)06/95]
While in the tape mode, push the right (
a) side of the
ªSEEKº button to seek forward to the next selection on the
tape. Push the left (
b) side of the ªSEEKº button to seek
the previous tape selection. The ªTAPEº display blinks.
*
[AS11400(ALL)09/95]
NOTE: If you want to restart a currently playing tape
selection, press the left (
b) side of the ªSEEKº button
after three seconds into the current selection.
[AS11500(ALL)06/95]4.
Using the ªSCANº button to scan cassette selections
[AS11600(ALL)06/95]
Press the ªSCANº button to enter the scan mode (display
blinks ªSCº) to begin the forward scan mode on the tape
currently playing, stopping on each tape selection for a
five-second sampling.
[AS11650(ALL)07/95]
The scan mode continues to the other side of the tape after
one side of the tape has been played completely.
[AS11800(ALL)06/95]
To stop the scan mode on the presently sampled tape
selection, press the ªSCANº button again, or press ªTAPE,º
ªCDº (if equipped), ªTUNE,º or ªSEEK.º
[AS11900(ALL)03/93]
Reversing the direction
[AS12000(ALL)06/95]
The alternate track of the tape can be selected anytime by
pressing the ªSIDE 1-2º button.
*
[AS12100(ALL)08/95]
How to eject the tape
*
[AS12200(ALL)01/95]
To stop the tape and eject the cassette, press the ªEJº button.
The radio will resume playing if the radio power is on. The
tape cartridge can be ejected with radio power (and/or ignition)
on or off.
File:04vxasn.ex
Update:Thu May 30 09:46:22 1996

212
*
[TO06100(ALL)01/96]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[TO06200(ALL)01/96]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[TO06300(ALL)01/96]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
%*
[TO06900(ALL)01/96]
For a cold engine:
*
[TO07000(ALL)01/96]
n
At temperatures10ÊF (-12ÊC) andbelow:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not
flood the engine, then try again.
*
[TO07100(ALL)01/96]
n
At temperaturesabove10ÊF(-12ÊC):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you do not flood the
engine, then try again.
*
[TO07200(ALL)01/96]
For a warm engine:
*
[TO07300(ALL)01/96]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, turn the key to the OFF
position. Wait a few seconds after the starter stops, then try
again.
*
[TO07350(ALL)01/96]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
*
[TO07360(ALL)01/96]
After you start the engine, let it idle for a few seconds.Keep
your foot on the brake pedaland release the parking brake.
Put the gearshift lever in gear, slowly release the brake pedal
and drive away in the normal manner.
File:08vxton.ex
Update:Thu May 30 09:53:35 1996

214
*
[TO08400(ALL)01/96]
RWARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up
the engine compartment and exhaust system, which can
start a fire.
*
[TO08500(ALL)01/96]
If you consistently start your vehicle in subzero temperatures,
use an engine block heater (if your vehicle has this option).
%*
[TO08600(ALL)01/96]
Engine Block Heater (If equipped)
[TO08700(ALL)01/96]
Engine block heaters are strongly recommended if you live in a
region where temperatures reachs10ÊF (s23ÊC) orbelow. An
engine block heater warms the engine coolant, which improves
starting, warms up the engine faster, and allows the
heater-defrost system to respond more quickly.
*
[TO08900(ALL)01/96]
RWARNING
To prevent electrical shock, do not use your heater with
ungrounded electrical systems or two-pronged (cheater)
adapters.
*
[TO09000(ALL)01/96]
For best results, plug the heater in at least three hours before
you start your vehicle. Using the heater for longer than three
hours will not damage the engine, so you can leave it plugged
in all night to start your vehicle the following morning.
%*
[TO09005(ALL)01/96]
What To Do If The Engine Does Not Start
%*
[TO09010(ALL)01/96]
Fuel Pump Shut-Off Switch
*
[TO09015(ALL)03/96]
If the engine cranks but does not start or does not start even
after a small collision, the fuel pump shut-off switch may have
been activated. The shut-off switch is a device intended to stop
the fuel pump when your vehicle has been involved in a
substantial jolt. Refer to theRoadside emergenciessection for more
information.
File:08vxton.ex
Update:Thu May 30 09:53:35 1996

216
*
[TO09065(ALL)01/96]5.
Check under the vehicle again for leaking fuel. If you see or
smell fuel, do not start your vehicle again. If there is no fuel,
you can try to start your vehicle again.
*
[TO09070(ALL)03/96]6.
Check all vehicle warning lights before driving your vehicle.
*
[TO09100(ALL)12/95]
Guarding Against Exhaust Fumes
*
[TO09200(ALL)01/96]
Carbon monoxide, although colorless and odorless, is present in
exhaust fumes. Take precautions to avoid its dangerous effects.
*
[TO09300(ALL)02/96]
RWARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open
the garage door before you start the engine.
*
[TO09400(ALL)01/96]
RWARNING
If you ever smell exhaust fumes of any kind inside your
vehicle, have your dealer inspect and fix your vehicle
immediately. Do not drive if you smell exhaust fumes.
These fumes are harmful and could kill you.
*
[TO09500(ALL)01/96]
Have the exhaust and body ventilation systems checked by a
qualified technician whenever:
*
[TO09600(ALL)01/96]
n
your vehicle is raised for service
*
[TO09700(ALL)01/96]
n
the sound of the exhaust system changes
*
[TO09800(ALL)01/96]
n
your vehicle has been damaged in an accident
*
[TO09900(ALL)01/96]
Improve your ventilation by keeping all air intake vents clear of
snow, leaves, and other objects.
*
[TO10000(ALL)01/96]
If the engine is idling while you are stopped in an open area
for long periods of time, open the windows at least one inch
(2.5 cm). Also, adjust the heating or air conditioning system to
bring in outside air.
File:08vxton.ex
Update:Thu May 30 09:53:35 1996

219
Driving
%*
[GF06200(ALL)05/96]
Brakes
*
[GF06300(ALL)01/96]
When the foot (service) brake pedal is depressed, the
high-mount brake lamp should illuminate.
*
[GF06400(ALL)01/96]
Front Disc Brakes
*
[GF06500(ALL)01/96]
The front disc brakes are self-adjusting. They do not require
service other than periodic lubrication of the caliper slide rails
and inspection for pad wear.
*
[GF06600(ALL)03/96]
Rear Drum Brakes
*
[GF06700(ALL)01/96]
The rear drum brakes are self-adjusting. Automatic adjustment
occurs through normal use of the brakes.
*
[GF06800(ALL)05/96]
Four-Wheel Anti-lock Brakes (If Equipped)
*
[GF06900(ALL)01/96]
The Anti-lock Brake System (ABS) prevents wheels from
completely locking up by automatically releasing and
re-applying the brakes. During ABS braking, slight brake pedal
pulsations may be felt on the driver's foot. These pulsations
represent the rapid cycling of the ABS valves. The pedal
pulsations are considered normal ABS operation, and will stop
when normal braking is resumed or when the vehicle comes to
a stop.
%*
[GF07000(ALL)01/96]
During ABS activation, a mechanical noise may be heard as the
ABS system cycles. This is normal ABS operation.
*
[GF07100(ALL)01/96]
The ABS system has self-check capabilities. The system turns on
the ABS warning light each time you start the engine. After the
engine is started and the ABS warning light turns off, the
system performs another test the first time the vehicle reaches
4 mph (6 km/h). A mechanical noise may be heard as the ABS
system performs a self test. This is a normal part of the self test
feature. If a malfunction is found during this check, the ABS
warning light will come on.
File:09vxgfn.ex
Update:Thu May 30 09:54:10 1996

Driving
225
[GF09800(ALL)01/96]
Shift-lock Safety Feature
[GF09810(ALL)01/96]
Your vehicle has a special shift-lock safety feature which
prevents you from shifting out of P (Park) without the brake
pedal depressed. To shift the transaxle out of the P (Park)
position, the ignition must be in the ON position and your foot
must be pressing on the brake pedal.
*
[GF09820(ALL)01/96]
If the shift lever cannot be moved from the P (Park) position
with the brake pedal depressed:
*
[GF09830(ALL)01/96]1.
Shut the engine off and remove the ignition key.
*
[GF09840(ALL)01/96]2.
Apply the parking brake.
*
[GF09850(ALL)05/96]3.
Reinsert the ignition key and turn it to the first position
(OFF).
*
[GF09860(ALL)01/96]4.
Depress the brake pedal, move the gearshift lever to N
(Neutral) and start the engine.
*
[GF09870(ALL)05/96]
If you need to shift out of P (Park) by using the alternate
procedure described above, it is possible that a fuse has blown
and that your brakelamps may also not be functional. Please
refer to the chapter titledRoadside Emergenciesin this Owner
Guide for instructions on checking and replacing fuses.
*
[GF09900(ALL)05/96]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL YOU VERIFY
THAT THE BRAKELAMPS ARE WORKING.
%*
[GF09950(ALL)01/96]
Backing Up
*
[GF09975(ALL)01/96]
Before shifting into or out of R (Reverse), you should always
come to a complete stop.
File:09vxgfn.ex
Update:Thu May 30 09:54:10 1996

Driving
227
*
[GF10450(ALL)01/96]
The transaxle will be in the ªoverdrive onº mode when the
vehicle is started even if the O/D OFF mode was selected when
the vehicle was last shut off.
[GF10500(ALL)01/96]
If your vehicle is on an extremely slippery surface, the
Electronic Transaxle Control Module may receive a signal
indicating a rapid increase or decrease in wheel speed. If the
module detects this condition, it will limit the transaxle
operation to Third gear and Reverse. This reduces tire slippage
and protects the transaxle. The transaxle will operate normally
in Reverse, but will lack power during acceleration in Drive. If
this happens, stop your vehicle as soon as possible and turn the
ignition off for 3 seconds. Restart the vehicle. If the condition
still exists, contact your dealer as soon as possible.
*
[GF10550(ALL)01/96]
NOTE: If the O/D OFF indicator light is flashing on and off
repeatedly when the vehicle is started, there is a
transaxle electronic system malfunction. Contact your
dealer as soon as possible.
*
[GF10600(ALL)05/96]
When to use 2 (Second)
[GF10650(ALL)01/96]
Use Second (2) when driving on slippery roads or to provide
additional engine braking on downgrades. This position
provides Second gear operation only. Do not exceed 68 mph
(110 km/h) in this position.
*
[GF10670(ALL)01/96]
When to use 1 (First)
[GF10700(ALL)01/96]
Use First (1) to provide maximum engine braking on steep
downgrades. Upshifts from First can be made by manually
shifting to Second (2) or Overdrive (D). First (1) gear provides
only first gear operation. If you select First while driving at
higher speeds, the transaxle will shift to Second (2), and then
shift back to First (1) after the vehicle decelerates to the proper
speed. Do not exceed 35 mph (56 km/h) in this position.
File:09vxgfn.ex
Update:Thu May 30 09:54:10 1996

238
*
[GF20200(ALL)01/96]
RWARNING
Always replace a fuse with one that has the specified
amperage rating. Using a fuse with a higher amperage
rating can cause severe wire damage and could start a
fire.
[GF20210(ALL)01/96]
Trailer Tow Module (If equipped)
[GF20220(ALL)01/96]
The trailer tow module on your vehicle (if equipped) allows
turn/stop lamp control on a trailer being towed by your
vehicle.
[GF20230(ALL)01/96]
The trailer tow package includes:
[GF20240(ALL)01/96]
n
trail or tow module which draws power from the vehicle
stop lamp fuse
[GF20250(ALL)01/96]
n
one SAE J1239 specified connector
[GF20260(ALL)01/96]
n
one extension harness within the rear bumper
[GF20270(ALL)01/96]
If you need further assistance in wiring a trailer to your vehicle,
contact your Ford or Lincoln-Mercury dealer.
%*
[GF20300(ALL)05/96]
Driving While You Tow
*
[GF20400(ALL)05/96]
Be especially careful when driving while you tow a trailer.
Never drive faster than 45 mph (70 km/h) when you tow in
hilly country on hot days. Also, anticipate stops so that you can
brake gradually.
*
[GF20500(ALL)01/96]
If you use the speed control while you are towing on very long,
steep grades, the speed control may shut off automatically.
*
[GF20600(ALL)01/96]
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift into
2 (Second) or 1 (First) gear.
File:09vxgfn.ex
Update:Thu May 30 09:54:10 1996