AR40.10-P-1040A
Balance wheels
27.1.95
MODELS
124, 129, 140, 163, 168, 170, 171, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240
MODEL
414
P40.10-0214-01
43a
Balance weight with retaining clip
43b
Adhesive weight
43c
Adhesive weight
P40.10-0215-01
P40.10-0216-01
43d
Balance weight for CTS wheel
43e
Support ring on CTS wheel
Balancing
1.1
Remove balance weight (43a) with retaining
clamp.
Installation tool
*124589176300
1.2
Remove adhesive weight (43b, 43c) with
removal tool
Removal tool
*129589005900
Use adhesive weights on light alloy disk
wheels with cramped installation conditions.
1.3
Remove balance weight for CTS wheel (43d)
from support ring (43e)
With special protection vehicles.
2
Clean wheels if necessary, attach to static
balancing machine and balance to a
maximum of 5 to 10g on each side of the
wheel.
Use recommended balancing machines;
observe manufacturer's instructions.
#
Mounting centering sleeve
AR40.10-P-1040-01A
Centering sleeve
*WH58.30-Z-1003-18A
Model 140, 210
Adjustment value on the balancing machine
for special protection vehicles with CTS
wheels.
AR40.10-P-1040-04A
3
Balance wheels on the vehicle
D
Wheels may only be finish-balanced on the
vehicle after they have been statically
balanced.
D
Vehicle doors must be closed.
D
Balance on steel rims with wheel covers.
D
Drive the rear wheels with the engine only
otherwise the rear axle center assembly will
be damaged.
Use recommended balancing machines;
observe manufacturer's instructions.
#
Type 124.2/3
Balancing on vehicles with 4MATIC
AR40.10-P-1040-02A
Models 124, 129, 140, 170, 202, 208, 210,
except 210.08/28
Balancing on vehicles with ETS, ASR or ESP
AR40.10-P-1040-03A
Copyright DaimlerChrysler AG 06.07.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
AR40.10-P-1010-01A
Checking condition of rim
P40.10-0259-01
1
Check inside and outside of wheel for dirt and clean wheel if necessary.
2
Check contact surface of rim for dirt and clean if necessary.
3
Check centering, spherical caps and rim flanges for damage. The spherical caps must be
free of grease.
Light-alloy rims
4
The rim flanges on light-alloy rims may exhibit increased levels of wear under the following
conditions:
High loads, operation with a trailer, insufficient tire inflation pressure, use of non-approved
tire makes or versions, contamination with dirt, sand and road salt.
5
The wear (X) must be no more than 1 mm.
Copyright DaimlerChrysler AG 06.07.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
AP40.10-P-4050GH
Remove/install wheels, rotate if necessary
15.7.97
MODEL
163
1-5
Tightening sequence
P40.10-0004-01
P40.00-0208-01
Remove
Danger!
Lethal injuries
are possible if vehicle slips off
of lifting platform
Align vehicle between the columns of the
lifting platform and position the four support
plates
at the lifting platform support points
specified by the vehicle manufacturer.
AS00.00-Z-0010-01A
Comply with notes on tires / rims
AH40.10-P-9411-01A
1
Raise vehicle.
AS00.00-Z-0010-01A
2
Unscrew wheel bolts, remove wheels
3
Check wheel bolts
The round contact shoulders on the lug
bolts must be free of oil and grease.
Replace bolts that have a damaged thread,
worn dacromet coating at radius seat or
corroded radius seat.
4
Check tires for damage and wear - measure
depth of tread
AP40.10-P-4051Z
5
Check disk wheels
D
check for contamination,
D
check that spherical caps are free of oil
and grease,
D
check centering, spherical caps and rim
flanges for damage,
D
check corrosion of lay-on surface
6
Check front wheel hub, brake disk bowl at
attachment face for contamination and
corrosion
Clean corroded surfaces with a wire brush or
an emery cloth.
Install
7
Change wheels around if necessary retaining
the same running direction
This excludes vehicles with mixed tires at
the front and rear axle.
Between
5,000 and 10,000 km according to wear.
8
Fit wheels, tighten wheel bolts
Observe tightening sequence "1-5".
*BA40.10-P-1001-01A
*126589040900
9
Lower vehicle, correct tire inflation pressure
(including spare wheel)
In the case of loss of tire pressure,
determine cause and replace tire if necessary.
On versions with spare tire attached to
underside of vehicle, check tire inflation
pressure of spare tire before lowering the
vehicle.
c
Deletion of spare tire with model 163.174
with TIREFIT
AH40.10-P-0001-01A
Wheels
Number
Designation
Models
163.113/128/
136/154/157/
172/175
Model
163.174
Copyright DaimlerChrysler AG 06.07.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
