1997 MERCEDES-BENZ ML350 brake fluid

Overview of authorized reworking on wiring harnesses
into the body
Lines get pinched in clamps
or trim parts
Fatigue Lines routed or secured
incorrectly
Excessive stress
Open circuit in wiring
Corrosion Due to contact with acids or
aggressive fluids (e.g. brake
fluid, antiseize, coolant
additives, fuels, lubricants),
water penetration due to
defective seals, use of high
pressure cleaner
Wiring harness covered in
paint after paint repair
Hardening of insulation due
to contact with an
incompatible agent (e.g.
solvent)
Line open circuit, contact
pairing not longer conductive
(transition resistances)
Insulation and wires
damaged
Lines or connections to
contacts
High line resistance
Components with sharp
edges
Corrosion
Assembly fault Use of incorrect tools, e.g.
wrong crimper or wrong
release tool
Damaged contacts or lines
through use of unsuitable test
tools (e.g. probes)
Lines pinched or screwed in
Loose contacts in plug
connections
Wrong contacts crimped
Undesirable transition
resistances
Open circuit in wiring, short-
circuit
Insulation damaged
Type of faultRemedial action
Faulty contact part
Contact part
missing
wrong part
deformed
Install new contact part
Contact part not engaged properlyLatch contact part, then check, and replace if
necessary
Not all individual wires are crimpedCut off contact part and install new part
Insulation also crimpedCut off contact part and install new part
Conductor not far enough in contact partCut off contact part and install new part

2004 Mercedes-Benz ML350
1998-2005 GENINFO Overall vehicle - 163 Chassis
me
Saturday, October 02, 2010 3:47:44 PMPage 22 © 2006 Mitchell Repair Information Company, LLC.

SPECIAL SERVICE PROCEDURES - AP00.20-P-0000-06B
Have the brake fluid replaced if more than 2 years have elapsed since the last change; this is best done in the
spring.
The coolant should be inspected for correct anticorrosion/ antifreeze concentration before the beginning of, and
during the cold season of the year. Depending on the model series, the coolant has to be replaced every 3 years
or 15 years (or after 250,000 km).
Refer to the particular valid service sheet for further additional operations based on kilometers or years.
SERVICE DATE REMINDER - AP00.20-P-0000-07B
The confirmation in the service booklet must be filled out completely and signed for every service (A or B).
Confirmation in the service booklet
Fig. 643: Identifying Service Date Reminder

SERVICE CARD FOR UNITS - AP00.20-P-0000-08A
Mercedes-Benz
Service card - major assembly
Maintenance
During the first service after exchanging a Mercedes-Benz genuine major assembly the operations listed in the
maintenance sheet or maintenance manual are to be carried out and confirmed.
Running-in:
The first 1 500 km
WARNING:When vehicles without service display are inspected, the assembly will be
serviced within the scope of the following care and/or maintenance
service.

2004 Mercedes-Benz ML350
1998-2005 GENINFO Overall vehicle - 163 Chassis
me
Saturday, October 02, 2010 3:47:52 PMPage 402 © 2006 Mitchell Repair Information Company, LLC.

CHECK ALL VISIBLE PARTS FOR SIGNS OF LEAKS AND DAMAGE - AP00.20-P-0053GH
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
INSPECTING CHASSIS AND LOAD-BEARING BODY PARTS FOR DAMAGE AND CORROSION - AP00.20-P-0090GH
MODEL 163
with Code Z04/Z07
Model 230AP00.20-P-0001L
Model 414AP00.20-L-0001A
Taxi serviceModels 202, 210AP00.20-P-0007A
Model 203AP00.20-P-0007C
Remove
Detach lower engine
compartment panelingModels 163.172/174/175AR61.20-P-1105GH
Remove noise
encapsulationModel 163.113/128AR94.30-P-5400GH
Check

2If traces of fluid are noted
(e.g. oil), then determine
and correct the cause (on a
separate work order).
Check for leaksEngine:
Transmission
Transfer case
Front axle
Rear axle
Pressure oil pump
3Check for leaks and fixingShock absorbers,
suspension struts
4Inspect for leaks and
conditionRubber boots of front axle
shafts
5Inspect lines and hoses for
leaks and condition, pay
attention to chafing points
and routingRadiator
Fuel system
Exhaust system
Clutch actuation
Automatic transmission
Power steering
Brake system
Install
Install lower engine
compartment paneling.Models 163.172/174/175AR61.20-P-1105GH
Install noise encapsulationModel 163.113/128AR94.30-P-5400GH
1Visual inspectionControl arm mountings and
control arms of front axle

2004 Mercedes-Benz ML350
1998-2005 GENINFO Overall vehicle - 163 Chassis
me
Saturday, October 02, 2010 3:47:52 PMPage 404 © 2006 Mitchell Repair Information Company, LLC.

procedure or when
working near engine
5Start engine Allow to run at idle
speed until oil pressure is
displayed.
6Check refrigerant level of
air conditioning systemModel 129 up to 31.5.96
with automatic air
conditioning, code 581a,AP83.30-P-8312DA
Model 140 up to 31.5.95
with automatic air
conditioning, code 581a
with rear air conditioner,
code 582,
Model 202 up to 30.9.95
with automatic air
conditioning, code 581a,
Models 129, 170, 202,
208, 210, 220 with air
conditioning (or
Tempmatic for USA),
code 580
Models 461, 463 with air
conditioning, code H02AP83.30-P-8312G
7Move the pull switch of
the hydropneumatic
suspension into position N
and allow the engine to
run at increased idle speed
until the vehicle has
reached its normal levelOnly for Hydropneumatic
suspension with automatic
level lowering device and
controlled damping, code
215c, All-round
hydropneumatic
suspension, code 487
8Brake testing on test standModel 129, 140, 170, 202,
203, 208, 209, 210, 215,
220AP42.00-P-4290BA
Models 461, 463AP42.00-P-4290G
9Check brake disks for
signs of corrosion. For vehicles which
were parked for more than
6 months.
10Replace brake fluid For vehicles which
were parked for more than
6 months.
Model 140 as of 1.7.93
except code 471AP42.00-P-4280BA
Model 170 except code
471
Model 202 up to 31.5.94
except code 471

2004 Mercedes-Benz ML350
1998-2005 GENINFO Overall vehicle - 163 Chassis
me
Saturday, October 02, 2010 3:47:52 PMPage 407 © 2006 Mitchell Repair Information Company, LLC.

GENERAL BRAKE FLUID - BB00.40-P-0330-01A
These specifications are valid for the Mercedes-Benz and smart brands.
General
The brake fluid in the brake system and in the hydraulic clutch operating system fulfills hydraulic tasks. Due to
the high heat build-up during braking, these tasks can only be fulfilled by brake fluids which comply with all of
today's technical requirements in terms of their various properties (viscosity-temperature-characteristic, boiling
point, corrosion protection, oxidation resistance, etc.).
The most important properties which a brake fluid must exhibit are:
High boiling point, to ensure that the brake fluid does not form vapor locks at high temperatures. Vapor
locks reduce the operating pressure and thus the braking effect and may ultimately lead to brake failure.
The boiling point should remain as constant as possible throughout the duration of use of the coolant and
not drop under varying atmospheric influences or operating conditions (pressure, temperature), i.e. the
"wet boiling point" should be as high as possible.
Low compressibility, in particular at high temperatures.
The low-temperature characteristic of the fluid - even when at 40°C - must permit operation, i.e.
primarily, the viscosity must not become too high in the cold.
Compatibility with the materials used in the brake units and clutch operating systems, e.g. the rubber
boots or any other seal materials (elastomers) included in the brake components may only swell to a
controlled extent, any shrinkage must be avoided.
Sufficient corrosion protection for all metals present in the brake system.
The brake fluids released for use in MB vehicle models are listed on Sheet 331.0. These brake fluids not only
comply with our requirements, but also those of the US safety specifications FMVSS 116, DOT 4. The released
"DOT 4 plus" brake fluids (internal designation) are more advanced DOT 4 brake fluids with higher wet boiling
point, standard change interval: 2 years. In order to be able to comply with this useful period without any
problem, we strongly advise the use of released products as per Sheet 331.0, during the warranty phase this is a
precondition for any acceptance of customer claims.
The brake fluid listed on Sheet 331.1 "DOT 4 Type 200" is released for special applications in the UNIMOG
range with more stringent thermal requirements. For this type of use, a brake fluid change interval of 1 year
must be adhered to.
Handling brake fluid
Brake fluid based on polyhydric alcohols in oligomer or polymer form and/or their
Esters are hygroscopic and thus absorbs moisture from the air. Water, however, reduces the boiling point of the
brake fluid, whereby the danger of vapor lock formation is present. Therefore it should be noted that brake fluid
is always stored in sealed vessels. Brake fluid that has been stored unsealed can absorb so much moisture in a
few hours that it is rendered unusable.

2004 Mercedes-Benz ML350
1998-2005 GENINFO Overall vehicle - 163 Chassis
me
Saturday, October 02, 2010 3:47:57 PMPage 530 © 2006 Mitchell Repair Information Company, LLC.

Because the brake fluid also absorbs moisture through the vent bore on the expansion reservoir, the wheel brake
cylinder and the brake hoses, the brake fluid has to be changed for safety reasons at regular intervals, best done
in the spring. When performing this change, make sure that the old fluid is also drained off the clutch system.
Generally, it is vital for the brake/clutch system to be completely drained before being filled with new fluid!
For the above-mentioned reasons, used brake fluid must not be used again.
The brake fluid is amber in color and thus can be easily confused with mineral products.
Therefore, brake fluids should always only be taken from original containers and stored separately from other
mineral oils and fluids.
When performing maintenance operations and repairs on brake parts, make sure that fuel, mineral oil, grease or
suchlike do not enter the brake system. Hydrocarbon-based materials will lead to swelling of the elastomers in
the brake and clutch system and - even in low concentrations - will suffice to cause total failure of the systems.
Only new brake fluid may be used as a rinsing and cleaning agent for the cylinders, lines and the expansion
reservoir of the hydraulic brake system.
Experience shows that before handling brake fluid, the hands must be cleaned and any oil and grease removed.
Brake fluid acts aggressively towards paint and color. In the event of any brake fluid spills or splashes, it must
be rinsed away immediately using copious amounts of water (do not rub it away).
Brake fluid disposal
When disposing of brake fluid, the relevant national specifications must be observed. It is advisable to try to
have the brake fluid disposed of as economic good; this is contingent on
Strict separation of used brake fluid from other materials;
Presence of a disposal channel, which justifies its classification as an economic good, i.e. a proper
alternate usage must be assured.
If this procedure is not possible, used brake fluid is to be disposed of together with any, e.g. paint residue,
solvents and suchlike. Any adding of used oil must be avoided, as it will result in difficulties, if the used oil is to
be recycled; in several countries this is prohibited by the legislators.
MISCELLANEOUS NOTES
NOTES ON SCRAPPING GAS-FILLED HYDRAULIC COMPONENTS - OS00.00-P-1000-01A
all
Unusable gas pressure dampers, spring accumulators, pressure reservoirs and impact absorbers have to be
depressurized before being scrapped according to the respective valid accident prevention regulations. These
safety measures are necessary because gas pressurized hydraulic parts can explode if heat is applied. A risk of
explosion is
given, e.g. when scrapping with cutting torches, smelting or if gas pressurized parts in landfills start

2004 Mercedes-Benz ML350
1998-2005 GENINFO Overall vehicle - 163 Chassis
me
Saturday, October 02, 2010 3:47:57 PMPage 531 © 2006 Mitchell Repair Information Company, LLC.

GF54.30-P-2001A
Indicator / warning displays, function
24.10.96

MODEL
129, 140 as of 1.6.96,

163, 168, 170,

202 as of 1.8.96,

208 up to 31.7.99,

210 as of 1.6.96 up to 30.6.99

The table below lists the various warning alarms and indications

according to type (visual/acoustic) and their actuation (direct/CAN).

Visual warning and indicator signals actuated over direct lines:
D
Left turn signal indicator lamp (A1e1)

D
Right turn signal indicator lamp (A1e2)

D
High beam indicator lamp (A1e3)

D
Fuel reserve warning lamp (A1e4)

D
Brake fluid / parking brake warning lamp (A1e7) (except model

163)

D
Low windshield washer fluid level warning lamp (A1e13) (as of

01.09.01 also valid for model 163)

D
Low engine coolant level warning lamp (A1e11) (except model

168, model 163 as of 3.99)

D
Coolant level and temperature warning lamp (A1e11) (only model

168 as of 9.99 and only coolant level function)

D
Generator charge indicator/warning lamp (A1e5)

D
Seat belt warning lamp (A1e9)

D
Seatbelt/backrest lock warning lamp (A1e9)

D
Exterior lamp failure indicator lamp (A1e14)

-----------------------------------------------------------------------------------------
D

Hydraulic fluid level warning lamp (A1e37)

D
ADS warning lamp, suspension (A1e27)

D
Steering lock warning lamp (A1e40) (only

I
)

D
SRS airbag malfunction indicator lamp (A1e15)

D
AIRBAG OFF indicator lamp (A1e56), only model 163 except

I

Also refer to document: Indicator and warning signals triggered

over CAN data lines
Acoustic warning and indicator signals actuated over direct

lines:
D
Turn signal ticker

D
Seat belt reminder

D
Switched-on lights reminder

D
Key warning

D
Soft top warning, only model 170


Also refer to document: Acoustic warnings, function

Acoustic warning and indicator signals actuated over CAN data

lines:
D
Parking brake warning

D
Vehicle speed warning

D
Vehicle speed limit warning

D
Gear warning, only model 168


Also refer to document: Acoustic warnings, function

Indicator and warning signals triggered over

direct lines

GF54.30-P-3002A

Indicator and warning signals triggered over

CAN data lines

GF54.30-P-3003A
Acoustic warnings, function
GF54.30-P-3010A

Copyright DaimlerChrysler AG 04.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1

GF54.30-P-2001A
Indicator / warning displays, function
24.10.96

MODEL
129, 140 as of 1.6.96,

163, 168, 170,

202 as of 1.8.96,

208 up to 31.7.99,

210 as of 1.6.96 up to 30.6.99

The table below lists the various warning alarms and indications

according to type (visual/acoustic) and their actuation (direct/CAN).

Visual warning and indicator signals actuated over direct lines:
D
Left turn signal indicator lamp (A1e1)

D
Right turn signal indicator lamp (A1e2)

D
High beam indicator lamp (A1e3)

D
Fuel reserve warning lamp (A1e4)

D
Brake fluid / parking brake warning lamp (A1e7) (except model

163)

D
Low windshield washer fluid level warning lamp (A1e13) (as of

01.09.01 also valid for model 163)

D
Low engine coolant level warning lamp (A1e11) (except model

168, model 163 as of 3.99)

D
Coolant level and temperature warning lamp (A1e11) (only model

168 as of 9.99 and only coolant level function)

D
Generator charge indicator/warning lamp (A1e5)

D
Seat belt warning lamp (A1e9)

D
Seatbelt/backrest lock warning lamp (A1e9)

D
Exterior lamp failure indicator lamp (A1e14)

-----------------------------------------------------------------------------------------
D

Hydraulic fluid level warning lamp (A1e37)

D
ADS warning lamp, suspension (A1e27)

D
Steering lock warning lamp (A1e40) (only

I
)

D
SRS airbag malfunction indicator lamp (A1e15)

D
AIRBAG OFF indicator lamp (A1e56), only model 163 except

I

Also refer to document: Indicator and warning signals triggered

over CAN data lines
Acoustic warning and indicator signals actuated over direct

lines:
D
Turn signal ticker

D
Seat belt reminder

D
Switched-on lights reminder

D
Key warning

D
Soft top warning, only model 170


Also refer to document: Acoustic warnings, function

Acoustic warning and indicator signals actuated over CAN data

lines:
D
Parking brake warning

D
Vehicle speed warning

D
Vehicle speed limit warning

D
Gear warning, only model 168


Also refer to document: Acoustic warnings, function

Indicator and warning signals triggered over

direct lines

GF54.30-P-3002A

Indicator and warning signals triggered over

CAN data lines

GF54.30-P-3003A
Acoustic warnings, function
GF54.30-P-3010A

Copyright DaimlerChrysler AG 05.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1