1997 LINCOLN CONTINENTAL hood release

223
Opening the Hood1. Inside the vehicle, pull the hood release handle
located under the bottom left corner of the
instrument panel.
The hood release under the instrument panel
File:11fnmcc.ex
Update:Fri Sep 6 08:51:16 1996

2242. Go to the front of the vehicle and release the
auxiliary latch that is located under the hood at
the center of the vehicle.
The auxiliary latch under the front edge of the
hood3. Lift the hood until the lift cylinders hold it
open.Whenever you close the hood, latch it securely.
NOTE:Apply lubricant to the hood latch at
six-month intervals to maintain smooth and
trouble-free operation.
NOTE:Read and understandPrecautions When
Servicing Your Vehicleat the beginning of this
chapter before opening the hood.
Engine CompartmentYour vehicle has a 4.6 liter 4V SFI engine. The
following page shows a diagram of where to find
items that you should regularly service.
File:11fnmcc.ex
Update:Fri Sep 6 08:51:16 1996

242If you do not let the engine relearn its idle, the idle
quality of your vehicle may be adversely affected
until the idle is relearned. Your vehicle will
eventually relearn its idle while you drive it, but it
takes much longer than if you use the previous
procedure.Passenger Compartment Air FilterUsing a screwdriver,
1. Remove the two screws retaining the passenger
side half of the cowl vent screen.
2. From inside the vehicle, pull the hood release.
3. Open the hood, then pull the hood pad away
from the cowl vent screen.
4. Remove the cowl vent screen, then the filter.
Reverse procedure to install. The filter must be
properly positioned in the housing for proper
installation.
Wiper BladesCheck the windshield wiper blades at least twice a
year. Also check them whenever they seem less
effective than usual. Substances such as tree sap
and some hot wax treatments used by commercial
car washes reduce the effectiveness of wiper blades.
If the blades do not wipe properly, clean both the
windshield and the wiper blades. Use undiluted
windshield washer solution or a mild detergent.
Rinse thoroughly with clear water. Do not use fuel,
kerosene, paint thinner, or other solvents to clean
your wiper blades. These will damage your blades.
To make reaching the wiper blades easy, simply
turn the ignition to the ACC position and turn your
wipers on. Wait for them to reach a vertical
position and turn the ignition to the OFF position.
Do not move the wipers manually. Manually
moving the wipers across the windshield may
damage them.
File:11fnmcc.ex
Update:Fri Sep 6 08:51:16 1996

314
calculating............. 184
definition.............. 183
driving with a heavy load....... 183
location............... 183
H
Hazard flashers............. 68
Headlamps
aiming............... 264
autolamp system........... 57
checking alignment.......... 261
cleaning.............. 261
daytime running lights........ 56
flashing............... 65
high beam............. 65
replacing bulbs........... 261
turning on and off.......... 57
warning chime............ 15
Head restraints............. 131
Heated mirrors............. 112
Heating
electronic automatic temperature control
system.............. 45High beams
indicator light............ 15
operation............ 56,65
Hood................. 223
latch location............ 223
lubrication specifications....... 273
release lever............. 223
working under the hood....... 221
Horn................. 69
I
Idle, relearning..........216, 221
Ignition
chime............... 63
positions of the ignition........ 62
removing the key.......... 63
Indicator lights and chimes (see Lights) . . . 7
Infant seats (see Safety seats)....148, 149
Instrument panel............. 7
cleaning............... 269
Interval wipers............. 66
File:fnixc.ex
Update:Tue Sep 17 08:28:54 1996