1997 ISUZU TFS SERIES wheel

FRONT WHEEL DRIVE 4C1-41
FRONT HUB AND DISC (42 model)
DISASSEMBLY
Refer to SECTION 3E “WHEEL AND TIRE” for wheel removal procedure.
Disassembly Steps
1. Bolt
2. Brake caliper
3. Hub cap
4. Split pin
5. Nut retainer
6. Hub nut
7. Lock washer8. Outer bearing
9. Hub and disc assembly
10. Oil seal
11. Inner bearing and outer race
12. Bolt
13. Wheel pin

4C1-42 FRONT WHEEL DRIVE
Important Operations
Before removal, jack up the front of vehicle and support frame
with jack stands.
2. Brake Caliper
(1) Remove the two bolts from the rear side of the knuckle arm,
then remove the brake caliper, with the brake hose
attached.
(2) Use a wire etc., for attaching the brake caliper to the upper
link.
3. Hub Cap
When removing hub cap, exercise care so as not to scratch or
distort hub fitting face.
9. Hub and Disc Assembly
Using a brass bar to remove the outer bearing outer race (1),
oil seal, inner bearing and inner bearing outer race (2) from the
hug.
If necessary, replace the wheel pin in the following manner.
12.Bolt
13.Wheel Pin ; Front Hub
(1) Scribe mark on hub to disc before disassembly to insure
proper assembly.

FRONT WHEEL DRIVE 4C1-43
(2) Clamp hub and disc assembly in vise using protective pads
and remove six (6) disc to hub retaining bolts.
(3) Place hub on a suitable work surface and remove wheel
studs, as required, using a hammer.

4C1-44 FRONT WHEEL DRIVE
INSPECTION AND REPAIR
Make necessary correction or parts replacement if wear, damage or any other abnormal conditions are found
through inspection.
Hub
Hub bearing
Bearing outer race
Disc
Oil seal
Visual Check
Check the following parts for wear, damage or other abnormal
conditions.

FRONT WHEEL DRIVE 4C1-45
REASSEMBLY
Refer to SECTION 3E “WHEEL AND TIRE” for wheel removal procedure.
Reassembly Steps
1. Wheel pin
2. Bolt
3. Inner bearing and outer race
4. Oil seal
5. Hub and disc assembly
6. Outer bearing
7. Lock washer
8. Hub nut
9. Nut retainer
10. Split pin
11. Hub cap
12. Brake caliper
13. Bolt

4C1-46 FRONT WHEEL DRIVE
Important Operations
1. Wheel Pin
(1) Place hub on a wood workbench or a block of wood,
approx. 6” by 6” to protect the wheel stud ends and threads.
(2) Install wheel stud using a hammer.
Be sure wheel stud is started squarely and seats
completely.
(3) Align index marks and install hub to disc.
2. Bolt
Torque N
m (kgfm/lbft)
103
5 (10.5 1/75.9 7.2)
3. Inner Bearing and Outer Race
4. Oil Seal
Outer Bearing Outer Race
(1) Install the bearing outer race by driving into the hub.
Installer (Outer) : 5-8822-0053-0 (J-29016)
Installer (Inner) : 5-8822-0054-0 (J-29015)
Drive handle : 5-8840-0007-0 (J-8092)
(2) Install the outer and inner bearing into the hub with fingers.

FRONT WHEEL DRIVE 4C1-47
(3) Install oil seal using special tools.
Installer : 5-8522-0051-0
(J-33161)
Grip : 5-8840-0007-0
(J-8092)
5. Hub and Disc Assembly
11. Hub Cap
Apply grease in the hub and hub cap.
Description Amount g(oz)
Hub 50 (1.76)
Hub cap 20 (0.70)
Outer bearing 6.5 (0.23)
Inner bearing 12 (0.42)
8. Hub nut
Adjustment of front wheel hub bearing preload
1. Tighten spindle nut to 3.0 kg
m (21.7 lb.ft/29.4 Nm) torque.
2. Turn the hub 2-3 turns and loosen the nut just enough so
that it can be turned with the fingers.
3. Turn the nut all the way in with the fingers and check to be
sure the hub has no free play.
4. Measure the bearing preload by pulling one of the wheel hub
studs with a spring scale.
5. Tighten the spindle nut until specified bearing preload Is
obtained.
After reassembling, install the disc brake caliper assembly.
Bearing Preload kg(lb)
New bearing and New oil seal 0.8 - 1.0(1.8 - 2.2)
Reuse bearing and New oil seal 0.8 - 1.0 (1.8 - 2.2)
13.Bolt
Torque N
m (kgfm/lbft)
155
15.7 (15.8 1.6/114.3 11.6)

4C1-48 FRONT WHEEL DRIVE
FRONT HUB AND DISC (44 model)
DISASSEMBLY
Refer to SECTION 3E “WHEEL AND TIRE” for wheel removal procedure
Disassembly Steps
1. Bolt
2. Hub cap
3. Snap ring and shim
4. Flange
5. Lock washer6. Hub nut
7. Hub and disc assembly
8. Outer bearing
9. Oil seal
10. Inner bearing