1997 HONDA CIVIC color code

[x] Cancel search: color code

transmission fluid bolt pattern wiper fluid coolant level reset airbag

Load previous 8 pages

Page 28 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Chassis and Paint Codes
Vohicle Grade
2: CX
4: DX
Check Digit
Model Yeal
Y: 2000
Fastory Code
H: Alliston Plant, Ontario. Canada
Serial Number
Vehicle ldentification NumbeI
and Federal Motor Vehicle
S

Page 29 of 2189

HONDA CIVIC 1997 6.G Workshop Manual t
U.S.2000 Model {4-door Sedan)
Vehicle ldentification Number
JHM EJ652*YS000001
Manufacturer, Makg and
Type of Vehicle
JHM: HONDA MOTOR CO.,
LTD.
HONDA Passenger
Vehicle
HONDA OF AMERICA
MFG., INC.
H

Page 30 of 2189

$HONDA CIVIC 1997 6.G Workshop Manual Chassis and Paint Codes U.S.2000 Model (2-door Coupe) Vehicle ldentification Number l HG EJ6 12 *Y1000001 Manufacturer. Make and Type ol Vehicle1HG: HONDA OF AMERICA t\4FG., tNC. HONDA Passenger Vehi$

Page 31 of 2189

HONDA CIVIC 1997 6.G Workshop Manual 2HG EJ632*YH 000001
ro
CANADA 2000 Model (2-door Hatchbackl
Vehicle ldentification Number
Manufaqturor, Make and
Type of Vehicle
2HG: HONDA OF CANADA
HONDA Passenger
Vehicle
Line, Body and Engine Type

Page 32 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Chassis and Paint Codes
Vehicle Grade
0: EX
1: LX-V
2: LX-V with ABS
3: LX
4: LX with ABS
5: LX with ABS and lyC
7: EX with ABS
8; EX with ABS and A,,/C
Check Digit
Model Y€ar
Y: 2000
Factory Code

Page 33 of 2189

HONDA CIVIC 1997 6.G Workshop Manual CANADA 2000 Model (2-door Coupel
Vehicle ldentification Number
lHG EJ6l 2 * Y 1800001
Manufacturer, Make and
Type of Vehicle
1HG: HONDA OF AMERICA
MFG,, INC.
HONDA Passenger
Vehicle
Line, Body and En

Page 206 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Main Bearings
4.
Glearance
1.To check main bearing-to-journal oil clearance.
remove the main caps and bearing halves.
Clean each main journal and bearing half with a
clean shop towel.
Place one strip

Main Bearings
4.
Glearance
1.To check main bearing-to-journal oil clearance.
remove the main caps and bearing halves.
Clean each main journal and bearing half with a
clean shop towel.
Place one strip of plastigage across each main jour-
na l.
NOTE: lf the engine is still in the car when you bolt
the main cap down to check clearance, the weight
of the crankshaft and flvwheel will flaften the plasti-
gage further than just the torque on the cap bolt.
and give you an incorrect reading. For an accurate
reading, support the crank with a jack under the
counterweights and check only one bearing at a
time,
Reinstall the bearings and caps, then torque the
bolts.
lst step: 25 N'm (2.5 kgl'm. 18 lbf'ft)
FinalsteD:
B16A2 engine:
76 N.m (7.8 kgf.m, 56 lbf'ft)
D16Y5, Dl6Y7, D16Y8 engines:
51 N.m (5.2 kgf'm, 38 lbf'ft)
NOTE: Do not rotate the crankshaft during inspec-
tron.
Remove the cap and bearing again, and measure the
widest part ot the plastigage.
Main Boaring-toJournal Oil Clearance:
816A2 engine:
Standald {New}:
No. l, 2, 4, 5 Journals:
O.O2,l - 0.042 mm 10'00(B - 0.0017 in)
No. 3 Journals:
0.030 - 0.048 mm {0'0012 - 0'0019 in)
Servico Limit: 0.06 mm {0.002 in,
Dl6Y5, Dl6
r, Dl6Y8 engines:
Standard (Nsw):
No. 1,5 Journals:
0.018 - 0.035 mm {0.0007 - 0'001'[ in)
No. 2. 3, 4 Journals:
0.02,1 - 0.0,(2 mm {0'0009 - 0.0017 in}
Service Limit: 0.05 mm (0.002 in)
\
7-9
7.
lf the plastigage measures too wide or too narrow,
(remove the engine if it's still in the car), remove the
crankshaft, and remove the upper half of the bear-
ing. Install a new. complete bearing with the same
color code {select the color as shown on the next
page), and rechsck the clearance.
CAUTION: Do nol fil€, shim, or scrape the bearings
or tho cap3 to adiust cleatanc€.
lf the plastigage shows the clearance is still incor-
rect, try the next larger or smaller bearing (the color
listed above or below that one), and check again
NOTE: lf the proper clearance cannot be obtained
by using the appropriate larger or smaller bearings,
replace the crankshaft and start over.

Page 207 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Main Bearing
Selection
CAUTION: lf the codes are indecipherable because of anaccumulation of dirt and dust, do not scrub them with a
wire brush or scraper. Clean them only with solvent ol
deiergent.
C

Load next 8 pages

Page: < prev 1-10 9-16 17-24 25-32 33-40 41-48 next >

traction control child lock horn oil pressure jacking points battery