1997 FORD RANGER lock

Seating and Safety Restraints
133
*
[SS15025(R)03/96]
RWARNING
Do not leave children, unreliable adults, or pets
unattended in your vehicle.
%*
[SS15900(R)01/96]
Safety Seats for Children
*
[SS16000(R)01/96]
Use a safety seat that is recommended for the size and weight
of the child. Always follow the safety seat manufacturer's
instructions when installing and using the safety seat.
*
[SS16015(R)01/96]
Ford recommends the use of a child safety seat having a top
tether strap. Install the child safety seat in a seating position
which is capable of providing a tether anchorage. For more
information on top tether straps seeAttaching Safety Seats With
Tether Strapsin this chapter.
*
[SS16025(R)05/96]
When installing a child safety seat, be sure to use the correct
safety belt buckle for that seating position, and make sure the
tongue is securely fastened in the buckle. For a shoulder/lap
belt combination with a sliding tongue, make sure the retractor
is in the automatic locking mode.
*
[SS16090(R)05/96]
All child restraint systems are designed to be secured in vehicle
seats by lap belts or by the lap portion of a lap-shoulder belt.
*
[SS16250(R)01/96]
RWARNING
Seatbacks should be upright for use with child safety
seats.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

Seating and Safety Restraints
139
[SS16580(R)03/96]5.
Grasp the shoulder portion of the belt and pull downward
until all of the belt retracted and a click is heard to put the
retractor in the automatic locking mode.
[SS16590(R)03/96]
17-1/2 pica
art:0011241-B
Setting the retractor to automatic locking mode
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

140
[SS16600(R)03/96]6.
Allow the belt to retract. The belt will click as it retracts to
indicate it is in the automatic locking mode.
[SS16610(R)03/96]
17-1/2 pica
art:0011242-B
Allowing shoulder belt to retract
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

142
[SS16640(R)03/96]8.
Allow the safety belt to retract to remove any slack in the
belt.
[SS16650(R)03/96]9.
Before placing the child in the seat, forcibly tilt the seat
forward and back to make sure the seat is securely held in
place.
[SS16660(R)03/96]
17-1/2 pica
art:0011244-B
Checking that the seat is secure
[SS16670(R)03/96]10.
Try to pull belt out of the retractor to make sure the
retractor is in the automatic locking mode (you should not
be able to pull more belt out). If the retractor is not locked,
unbuckle the belt and repeat steps 2 through 9.
[SS16680(R)03/96]
To remove the retractor from automatic locking mode, allow
webbing to retract fully to its stowed position and the retractor
will automatically switch back to the vehicle sensitive locking
mode for normal adult usage.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

Starting
153
*
[TO10400(R)01/96]
If the engine is idling while you are stopped in an open area
for long periods of time, open the windows at least one inch
(2.5 cm). Also, adjust the heating or air conditioning system to
bring in outside air.
[TO10650(R)01/96]
n
HEATING Ð Set fan speed to medium or high, the function
control knob on any position except OFF and the
temperature control knob on any desired position.
[TO10700(R)01/96]
n
AIR CONDITIONING Ð Set fan speed to medium or high
with the function control knob on any position (except OFF
or MAX A/C) and the temperature control knob at a
comfortable level.
*
[TO13076(R)03/96]
Removing the Key From the Ignition
*
[TO13100(R)03/96]
Procedures for removing your key from the ignition will vary,
depending on the type of gearshift your vehicle has. Gearshift
levers may be mounted on the steering column or on the floor
or console.
[TO13117(R)01/96]
If you have a manual transmission, you have a key release lever
which allows you to remove your key from the ignition. The
key release lever is on the upper right of the steering column,
just above the key lock cylinder.
*
[TO13300(R)03/96]
If your vehicle's gearshift lever is mounted on the
column:
*
[TO13400(R)03/96]1.
Put the gearshift in P (Park).
*
[TO13500(R)03/96]2.
Set the parking brake fully before removing your foot from
the service brake. (This will avoid ªbindingº or ªloadingº the
park gear if you park on a grade.)
*
[TO13600(R)03/96]3.
Turn the ignition key to LOCK.
*
[TO13700(R)03/96]4.
Remove the key.
File:08untor.ex
Update:Thu Mar 20 08:53:27 1997

Driving
163
[GF00900(R)05/96]
Automatic Transmission Operation
(4R44E/5R55E)
[GF08715(R)05/96]
If your vehicle is equipped with an automatic transmission, it
will be either a four speed overdrive transmission (4R44E) or a
five speed overdrive transmission (5R55E). All 2.3L and 3.0L
engines use the 4R44E transmission, while all 4.0L engines use
the 5R55E transmission. Both transmission types have a lockup
torque converter. Transmission operation is controlled by the
Powertrain Control Module (PCM).
*
[GF08720(R)01/96]
The PCM will automatically adjust transmission operation to
make up for varying conditions. Several sensors located on the
engine and transmission such as throttle position, engine speed,
vehicle speed and transmission temperature are used by the
PCM to shift the transmission into a higher or lower gear when
required for the best performance and fuel economy. For
example, you may notice that the transmission will upshift to a
higher gear more quickly when the vehicle has not reached
normal operating temperature.
*
[GF08730(R)01/96]
The PCM also controls the transmission's Torque Converter
Clutch (TCC) to further raise vehicle performance and fuel
economy. The TCC will engage when the transmission operating
temperature and other conditions determined by the PCM have
been met. Engagement of the clutch may be noted as a decrease
in engine speed.
[GF08740(R)05/96]
To help in troubleshooting, the PCM continually performs
self-tests on the electronic control system and, if any faults are
detected, stores them in memory. The Transmission Control
Indicator Light (TCIL) (O/D OFF), which is located on the
instrument cluster, may flash steadily if a malfunction has been
detected. If the TCIL is flashing, contact your Ford dealer as
soon as possible. If this condition persists, damage to the
transmission could occur.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

170
*
[GF10445(R)05/96]
When to use 1 (Low)
*
[GF10450(R)05/96]
With the gearshift in the 1 (First) position, maximum engine
braking is provided. This position provides 1 (First) gear
operation only with no automatic upshifts. To obtain upshifts,
the gearshift must be moved out of this position. Use the 1
(First) position to drive up steep grades or to provide maximum
engine braking on downgrades.
*
[GF10455(R)05/96]
Forced Downshifts
[GF10460(R)05/96]
To gain acceleration in
j(Overdrive) or Drive (O/D OFF)
when passing another vehicle, push the accelerator to the floor.
The transmission will downshift to the appropriate gear: fourth,
third, second or first gear.
%*
[GF10490(R)05/96]
Traction-Lok Rear Axle (If equipped)
*
[GF10492(R)05/96]
This axle provides added drive away traction on slippery
surfaces, particularly when one or more wheels are on a surface
with poor traction.
*
[GF10494(R)03/96]
Extended use of other than matching size tires on a
Traction-Lok rear axle could result in a permanent reduction in
effectiveness. This loss of effectiveness does not affect normal
driving and should not be noticeable to the driver.
[GF11300(R)01/96]
Manual Transmission Operation
%*
[GF11400(R)01/96]
Using the Clutch
*
[GF11500(R)01/96]
Make sure the gearshift lever is in the N (Neutral) position and
your right foot is holding down the brake pedal. Then press the
clutch pedal to the floor with your left foot. Manual
transmission vehicles have a starter interlock switch. The starter
will not crank until the clutch pedal is fully depressed. Start the
engine and allow it to idle for a few seconds. Move the
gearshift into 1 (First) or R (Reverse).
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

172
*
[GF12600(R)01/96]3.
Put the gearshift in Neutral and wait at least 3 seconds
before shifting into R (Reverse) to prevent a grinding noise.
Do not release the clutch.
*
[GF12700(R)01/96]4.
Push the gearshift all the way to the right and pull it back
into Reverse.
*
[GF12800(R)01/96]
With the 5-speed transmission you can engage R (Reverse) only
by moving the gearshift from the left of 3 (Third) and 4 (Fourth)
gears before you shift into R (Reverse). This is a special lockout
feature that protects you from accidentally shifting into R when
you downshift from 5 (Fifth) gear.
*
[GF12900(R)01/96]5.
Once R (Reverse) is engaged, slowly release the clutch pedal
from the floor.
*
[GF13000(R)01/96]
If R (Reverse) is not engaged, continue to push the clutch pedal
in while you put the gearshift back into Neutral. Then, release
the clutch pedal for a moment and repeat steps 2 through 5.
*
[GF13100(R)01/96]
Upshifting/downshifting
[GF13200(R)03/96]
Upshift and downshift at the speeds that are specified in the
charts.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997