1997 FORD F250 ABS

16 %
*
[IS03200(F )03/96]
Anti-Lock Brake System Warning Light
*
[IS03300(F )04/96]
To check the ABS brake warning light turn the
ignition key to ON. The ABS brake warning
light should glow momentarily.
*
[IS03400(F )03/96]
NOTE: If it does not glow momentarily, have
your vehicle's electrical system checked
immediately.
[IS03500(F )04/96]
NOTE: If the ABS brake warning light begins
to flash in a repeatable flash sequence,
check the rear anti-lock system
continuous power fuse and brake lights
for proper operation.
[IS03600(F )04/96]
one inch art:0020913-B
Antilock warning light
*
[IS03700(F )03/96]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
*
[IS03800(F )03/96]
NOTE: If a fault occurs in the anti-lock
system, and the brake warning light is
not lit, the anti-lock system is disabled
but normal brake function remains
operational.
File:03ltisf.ex
Update:Tue May 28 08:40:24 1996
ProCarManuals.com

48
*
[AS25700(F )12/95]
How to locate a desired track on the tape
*
[AS26265(F )08/95]
q
Using the Automatic Music Search (ªAMSº)
*
[AS26270(F )03/96]
Press and hold the ªAMSº button (ªAMSº will
appear in the display). Then, push the left
h
button to rewind to the beginning of the current
selection or press the right
gbutton to fast
forward to the beginning of the next selection.
*
[AS26900(F )08/95]
q
How to change the side of the tape being
played
*
[AS27000(F )09/95]
The alternate track (other side) of the tape
can be selected at any time by pushing both
fast-wind buttons (
hand
g) at the
same time. The number in the display will
alternate between 1 and 2.
*
[AS27100(F )08/95]
How to eject the tape
*
[AS27250(F )04/96]
To stop the tape and eject the cassette, press the
eject (i) button. The radio will resume playing.
*
[AS27300(F )02/96]
Using the DolbyHB noise reduction feature
*
[AS27500(F )04/96]
Push thekbutton to activate. Push again to
deactivate.
*
[AS27550(F )09/95]
NOTE: Noise reduction system manufactured
under license from Dolby Labs
Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of
Dolby Laboratories Licensing
Corporation.
%*
[AS27555(F )01/96]
Clock Operation
*
[AS27560(F )08/95]
How to view the clock mode
*
[AS27565(F )08/95]
Press the ªCLOCKº button to alternate the
frequency and time in the display. In the clock
mode, pressing any radio function will
automatically display the radio frequency for
approximately ten seconds before changing back
to the clock mode.
File:04ltasf.ex
Update:Tue May 28 08:40:59 1996
ProCarManuals.com

134 [SS36000(F )04/96]If a tethered seat is installed in the front seat,
Ford recommends placement of the tethered
safety seat in the center front seating position,
with the tether strap secured to the center rear
lap belt tongue or to the webbing of the buckled
center rear lap belt behind the child safety seat.
[SS36100(F )04/96]
The rear lap/shoulder safety belts should not be
used to secure the tether strap of a safety seat
located in the front seat.
*
[SS36200(F )01/96]
RWARNING
Follow these precautions to decrease the
chance of injury in an accident.
*
[SS36400(F )03/96]
In SuperCabs equipped with Center Facing Jump
Seats, the tether strap anchor bracket should be
installed only at the center of the cab's back
panel with the child seat in the front center
seating position. Installing an anchor bracket at
the right rear of the cab may increase risk of
injury to an occupant of the right rear center
facing jump seat in the event of a collision or
sudden stop. If a tethered child seat is installed
in the right front seating position, secure the
tether strap to the webbing of the buckled right
rear lap belt.
*
[SS36500(F )01/96]
RWARNING
Do not install a child seat in a center
facing jump seat.
File:06ltssf.ex
Update:Tue May 28 08:44:33 1996
ProCarManuals.com

298 [MC34800(FM)04/96]If any fuel is swallowed, call a physician or
poison control center immediately. Do not delay
calling a physician merely because no adverse
effects are noticed at first; the toxic effects of a
gasoline-methanol blend, including blindness,
may not become apparent for many hours.If
gasoline is swallowed, do not induce vomiting.
If a gasoline-methanol blend is swallowed,
induce vomiting under the direction of a
physician or poison control center.
*
[MC34900(FM)01/96]
Gasoline and gasoline-methanol blends may
contain small amounts of carcinogens, such as
benzene. Long-term exposure to unleaded
gasoline vapors has caused cancer in laboratory
animals. Further, excessive inhalation of fuel
vapors can cause headache, dizziness, nausea,
loss of coordination, and other symptoms which
could interfere with your ability to safely
operate your vehicle. To the extent possible,
avoid breathing vapors while refueling. If fuel
vapors are inhaled in excessive quantities, move
the victim to fresh air and seek medical
attention.
*
[MC35000(FM)01/96]
Fuels can also be harmful if absorbed through
the skin. When refueling, be careful not to
splash fuel on yourself or your clothing. If fuel
is splashed on the skin, promptly remove
contaminated clothing and wash the skin
thoroughly with soap and water.
*
[MC35100(FM)01/96]
Fuels can cause severe eye irritation and possibly
eye damage. If fuel is splashed in the eyes,
remove contact lenses (if worn), flush with large
amounts of water for 15 minutes, and seek
medical attention.
File:11ltmcf.ex
Update:Tue May 28 08:52:04 1996
ProCarManuals.com

304
*
[MC39300(FM)01/96]
By law, anyone who manufactures, repairs,
services, sells, leases, trades vehicles, or
supervises a fleet of vehicles is not permitted to
intentionally remove an emission control device
or prevent it from working. In some of the
United States and in Canada, vehicle owners
may be liable if their emission control device is
removed or is prevented from working.
*
[MC39325(FM)01/96]
Do not drive your vehicle if it does not operate
properly. See your dealer if the engine runs on
for more than five seconds after you shut it off
or if it misfires, surges, stalls, or backfires.
%*
[MC39350(FM)01/96]
Information about your vehicle's emission
control system is on the Vehicle Emission
Control Information decal located on or near the
engine. This decal identifies engine displacement
and gives some tune-up specifications.
[MC39375(F )04/96]
NOTE: All current model year vehicles are
certified to the same year emissions
standards except certain vehicles
equipped with engines built prior to
January 1 of the model year which may
be certified to prior year emissions
standards. In either case, the
maintenance schedules contained in the
back of this Owner Guide must be
used to maintain your engine.
% [MC39400(FM)04/96]
Noise emissions warranty, prohibited
tampering acts
[MC39425(FM)04/96]
On January 1, 1978, Federal regulations became
effective governing the noise emissions on trucks
with a GVWR of over 10,000 lbs (4,536 kgs). The
following statements concerning prohibited
tampering acts and the noise warranty are found
in theWarranty Information Booklet, and are
applicable to completed F-Series chassis cabs
whose GVWR is over 10,000 lbs (4,536 kgs).
File:11ltmcf.ex
Update:Tue May 28 08:52:04 1996
ProCarManuals.com

305 [MC39475(FM)04/96]
Do not tamper with the noise control
system
[MC39500(FM)04/96]
Federal law prohibits the following acts:
[MC39525(FM)04/96]
1. The removal or dismantlement, (by any
person unless for maintenance, repair or
replacement purposes) of any device or
design element incorporated into any new
vehicle to control noise output, prior to its
sale or delivery to the consumer, or while it
is being used, or
[MC39550(FM)04/96]
2. Using your vehicle after a device or design
element has been removed or dismantled, by
any person.
[MC39575(FM)04/96]
The following are some of the acts that are
considered tampering:
[MC39600(FM)04/96]
q
Removing the hood blanket, fender apron
absorbers, fender apron barriers, underbody
noise shields or material constructed to
absorb noise output.
[MC39650(FM)04/96]
q
Removing or dismantling the engine speed
governor, so that the engine's speed exceeds
the manufacturer's specifications.
[MC39675(FM)04/96]
q
Removing the air duct, air intake choke or
silencer, air cleaner and/or air cleaner
element.
[MC39700(FM)04/96]
q
Removing or dismantling any of the exhaust
system components including the catalyst
inlet pipe, muffler, outlet pipe, resonator or
diffuser.
[MC39725(FM)04/96]
q
Removing the fan shroud. Removing or
dismantling the fan clutch so that it no longer
functions properly.
File:11ltmcf.ex
Update:Tue May 28 08:52:04 1996
ProCarManuals.com

309
*
[MC42200(F )03/96]
Removing the headlamp bulb
*
[MC42250(F )01/96]
1. Make sure that the headlamp switch on the
instrument panel is in the OFF position.
[MC42300(F )04/96]
2. Lift the hood and behind the headlamp
remove the electrical connector by grasping
the wires and pulling rearward.
*
[MC42550(F )01/96]
3. Remove the bulb retaining ring by turning it
1/8 of a turn to free it from the socket. Then
slide the ring off the plastic base. Keep the
ring.You must use it again to hold the new
bulb in place.
*
[MC42650(F )01/96]
4. Carefully remove the bulb assembly from its
socket by gently pulling it rearward without
turning.
*
[MC42750(F )03/96]
Installing the headlamp bulb
*
[MC42800(F )01/96]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[MC42850(F )01/96]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstop.º
*
[MC42900(F )01/96]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[MC43000(F )01/96]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
File:11ltmcf.ex
Update:Tue May 28 08:52:04 1996
ProCarManuals.com

Index 367
Index
A
ABS warning light
(see Anti-lock brake system)....... 16
Accessory position on the ignition . . . 67±68
Accessory power source, power
point outlet.............. 66
Additives, engine oil.......... 264
Air bag supplemental restraint system,
and child safety seats......... 122
Air cleaner filter
location............... 261
specifications............. 317
Alarm, activating remote personal..... 90
Alcohol, in fuel............. 297
Antenna, radio (see Electronic
sound system)............. 27
Antifreeze (see Engine coolant)...... 274
Anti-lock brake system (ABS)
description.............. 145
see also Brake............ 145
warning light.............. 16
warninig light............. 15
Appeals (see Dispute settlement board) . . 338
Assistance (see Customer assistance) . . . 335
Audio system (see Electronic
sound system)............. 27
Autolamp system (see Headlamps)..... 63
Automatic transmission
driving an automatic overdrive . . 151, 155
fluid, adding............. 284
fluid, checking............ 283
fluid, refill capacities......... 318
fluid, specification.......... 324
File:ltixf.ex
Update:Tue May 28 08:56:20 1996
ProCarManuals.com