1997 FORD EXPLORER seat memory

Rear console features
The rear console incorporates the
following features:
²air vents
²audio system controls
²rear seat climate controls
²cupholders
Refer to the ªAudio Guideº for
more information on the rear
console audio system controls.
Rear console climate controls
Turn the air distribution control to
the desired airflow position.
Turn the fan speed dial to the
desired position.
SEEK
– VOLUME + BAND
MEMORY
SEEK
– VOLUME + BAND
MEMORY
uno_climate_controls_rear
Controls and features
61

Selectfor air to flow through
these vents:
Select
for air to flow through
these vents:
FLOOR MATS
Installing the floor mats
1. Move the driver's seat to the
most rearward position.
2. Position the driver's side floor
mat with the rear of the mat
SEEK– VOLUME + BAND
MEMORY
SEEK– VOLUME + BAND
MEMORY
uno_mats-for-floors
uno_hooking_floor_mat
Controls and features
62

Locking the doors
Press LOCK to lock all doors.
To confirm all doors are closed and
locked, press the LOCK control a
second time within five seconds.
The doors will lock again, the horn
will chirp and the lamps will flash.
If the horn chirps twice, a door is
still ajar and the anti-theft system
will not arm.
Sounding a panic alarm
Press the PANIC control to
activate the horn and lights.
To deactivate the alarm, press the
PANIC control again or turn the
ignition to the Acc or On position.
Remote memory seat feature
(if equipped)
The remote keyless entry system
can control the Memory Seat
system (refer to theMemory seat
section in theSeating and safety
restraintschapter. Each of the
first three transmitters
programmed recall a different seat
position.
PANICUN
LOCKLOCK
LOCK
PANICUN
LOCK
uno_remote_panic
uno_remote_memory_seat
Controls and features
70

Pressing UNLOCK once will:
²unlock the driver's door and
²move the seat to its
corresponding memory seat
position.
When your dealer programs new
transmitters, the order of
programming controls seat recall
as follows:
²First transmitter programmed
recalls seat position one
²Second transmitter programmed
recalls seat position two
²Third transmitter programmed
recalls seat position three
²Fourth transmitter programmed
recalls no seat position
You may change seat positions at
any time.
You can deactivate or reactivate
the remote memory seat feature:
1. Make sure the anti-theft system
(if equipped) is not armed or
triggered, ignition is off and all
doors and liftgate window are
closed.
2. Turn the ignition key from OFF
to ON.
3. Press the door power unlock on
the door switch three times.
4. Turn the ignition key from ON
to OFF.
LOCK
PANICUN
LOCK
Controls and features
71

5. Press the door power unlock
switch three times.
6. Turn the ignition key back to
ON within 30 seconds of step two.
7. The horn should chirp once. If
not, wait 30 seconds and repeat
steps one through six.
8. Press the door power unlock
switch twice.
9. Press the door power lock
switch.
10. The horn will chirp twice if the
remote memory seat feature was
deactivated, three times (two short
chirps followed by a long chirp) if
the remote memory seat feature
was activated.
11. Turn the ignition key to OFF.
12. The horn will chirp once to
confirm that you activated or
deactivated the remote memory
seat feature.
To reactivate the system, simply
repeat the instruction for
deactivating. By reentering the
code that deactivates the remote
memory seat, the keyless entry
system reinstates the feature.
The memory seat function will
continue to work from the door
switch even when deactivated at
the remote keyless entry module.
Replacing the batteries
The transmitter is powered by two
coin-type three-volt lithium
batteries. A decrease in operating
range can be caused by:
uno_remote_batteries
Controls and features
72

Press to increase (+ ) or decrease
(-) lumbar support.
Memory seats (if equipped)
This system allows automatic
positioning of the driver seat to
three programmable positions.
²To program position one, move
the driver seat to the desired
position using the seat controls.
Press the SET control. The SET
control indicator light will briefly
illuminate. While the light is
illuminated, press control 1.
²To program position two, repeat
the previous procedure using
control 2.
²To program position three,
repeat the previous procedure
but press controls 1 and 2
simultaneously.
A position can only be recalled
when the automatic transmission
gearshift is in P (Park) or the
manual transmission gearshift is in
N (Neutral). A memory seat
position may be programmed at
any time.
+–
SET
12
uno_remote_seat_controls
uno_seat_belts
Seating and safety restraints
82

Number Fuse Amperage
RatingCircuits Protected
1 7.5 amp Power mirror, power
antenna
2 7.5 amp High-mount brakelamp
3 15 amp Parking lamp,
instrument cluster
gauges
4 10 amp Left headlamp, lamp
out warning
5 10 amp OBD system
6 7.5 amp Air bag system, blower
relay, EATC
7 7.5 amp Illumination switches
8 10 amp Right headlamp, fog
lamp system, DRL,
lamp out warning
9 10 amp EATC system, seat
memory, message
center, cellular phone,
autolamps
10 7.5 amp EATC system, rear
blower, speed control,
GEM system, brake
interlock, overhead
console, automatic
ride control, lamp out
warning
11 7.5 amp Warning lamps,
autolamp
12 10 amp Front washer, rear
washer & wiper
Roadside emergencies
151

Number Fuse Amperage
RatingCircuits Protected
28 7.5 amp Memory seat, GEM
system
29 10 amp Audio system
30 - Not used
31 7.5 amp Rear blower system
32 7.5 amp Heated mirror, rear
defroster
33 15 amp High beam lamps
34 7.5 amp Lux audio system
Power distribution box
Always replace the cover
to the Power Distribution
Box before reconnecting the
battery or refilling fluid
reservoirs.
High current fuse rating Color
30 amp Light green
40 amp Orange
50 amp Red
60 amp Blue
14 13
12 11
10 9
87
65
43
2
8
47
36
25
1
11 10 9
1
uno_power_distribution_box
Roadside emergencies
153