1997 FORD ASPIRE lock

144 [ER12600(ALL)01/96]When calling for a tow truck, tell the operator
what kind of vehicle you have. A towing
manual is available from Ford Motor Company
for all authorized tow truck oerators. Have your
tow truck driver refer to this manual for the
proper hook-up and towing procedures for your
vehicle.
*
[ER13000(ALL)01/96]
Towing With the Back Wheels Off the
Ground
[ER13150(ALL)01/96]
If it is necessary to tow your vehicle from the
rear (with the rear wheels off the ground), a
dolly must be placed under the front tires to
prevent transaxle damage.
*
[ER13200(ALL)01/96]
Do not use your vehicle's steering column lock
to secure the wheels in a straight-ahead position.
Always use a steering wheel clamping device
designed for towing service.
*
[ER13250(ALL)01/96]
Refer toTowing behind another vehicle
Ðrecreational vehiclein the Index for information
on towing behind an RV.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

147
*
[MC02000(ALL)01/96]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[MC02100(ALL)01/96]
q
Never get under a vehicle while it is
supported only by a jack. If you must work
under a vehicle, use safety stands.
*
[MC02200(ALL)01/96]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[MC02700(ALL)01/96]
Working with the engine off:
[MC02750(ALL)01/96]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or 1 (First) gear
(manual transaxle).
*
[MC02800(ALL)01/96]
2. Remove the key from the ignition after you
turn the engine off.
*
[MC02850(ALL)01/96]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC02900(ALL)01/96]
Working with the engine on:
*
[MC03000(ALL)01/96]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or Neutral (manual
transaxle).
*
[MC03050(ALL)01/96]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC03200(ALL)01/96]
WARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

157
*
[MC18700(ALL)05/96]
WARNING
Never remove the coolant recovery cap
while the engine is running or hot.
*
[MC18800(ALL)05/96]
If you must remove the coolant recovery cap,
follow these steps to avoid personal injury
caused by escaping steam or engine coolant:
*
[MC18820(ALL)05/96]
1. Before you remove the cap, turn the engine
off and let it cool.
*
[MC18830(ALL)05/96]
2. When the engine is cool, wrap a thick cloth
around the cap and turn it slowly,
counterclockwise to the first stop.
*
[MC18840(ALL)05/96]
3. Step back while the pressure releases.
*
[MC18850(ALL)05/96]
4. When you are sure that all the pressure has
been released, use the cloth to press the cap
down, turn it counterclockwise, and remove
it.
[MC18900(ALL)05/96]
UseFord Premium Engine Coolant
E2FZ-19549-AA(in Canada, Motorcraft CXC-8-B)
or an equivalent premium engine coolant that
meets Ford Specification ESE-M97B44-A. Ford
Premium Engine Coolant is an optimized
formula that will protect all metals and rubber
elastomers used in Ford cooling systems for 4
years or 50,000 miles (80,000 km).
[MC19000(ALL)05/96]
Do not use alcohol or methanol antifreeze or any
engine coolants mixed with alcohol or methanol
antifreeze. Do not use supplemental coolant
additives in your vehicle. These additives may
harm your engine cooling system.The use of an
improper coolant may void the warranty of
your vehicle's engine cooling system.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

166
*
[MC30500(ALL)02/96]
Wiper blade replacement
*
[MC30600(ALL)01/96]
If the wipers still do not work properly after
you clean them, you may need to replace the
wiper blade assembly. When replacing the wiper
blade assembly always use a Motorcraft part or
equivalent.
*
[MC30700(ALL)08/95]
To replace the wiper blades:
*
[MC30800(ALL)01/96]
1. Pull the wiper arm away from the
windshield and into the lock position.
*
[MC30900(ALL)01/96]
2. Turn the blade at an angle from the wiper
arm. Push the lock pin with a screwdriver to
release the blade and pull the wiper blade
down toward the windshield to remove it
from the arm.
*
[MC31000(ALL)08/95]
3. Attach a new wiper blade to the wiper arm
and press it into place until you hear it click.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

176
*
[MC43825(ALL)01/96]
To fill the tank properly:
*
[MC43830(ALL)01/96]
1. Remove the fuel cap. Proceed to add fuel to
the tank only if your vehicle is on level
ground.
[MC43835(ALL)01/96]
2. Make sure that you pump unleaded fuel and
put the nozzle all the way inside the fuel
filler pipe. The fuel tank is normally full
after three automatic shutoffs of the nozzle.
*
[MC43840(ALL)01/96]
3. If you spill any fuel on the body of your
vehicle, clean it off immediately. The fuel
may dull or soften the paint if you do not
wash it off.
[MC43845(ALL)01/96]
4. Replace the fuel cap tightly when you are
finished. Turn it clockwise until you hear at
least three clicks.
*
[MC43850(ALL)01/96]
5. Push the fuel door closed.
%*
[MC43855(ALL)08/96]
Choosing the Right Fuel
*
[MC43861(ALL)05/96]
Use only UNLEADED FUEL. The use of leaded
fuel is prohibited by law and could damage
your vehicle. The damage may not be covered
by your warranty.
*
[MC43866(ALL)08/96]
Your vehicle was not designed to use fuel
containing manganese-based additives such as
MMT. Additionally, vehicles certified to
California emission standards (indicated on the
underhood Vehicle Emissions Control
Information label) are designed to operate on
California reformulated gasolines. If California
reformulated gasoline is not available when you
refuel, your vehicle can be operated on
non-California fuels. However, even though your
engine will perform adequately on other
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

186
*
[MC61900(ALL)01/97]
Removing the headlamp bulb
*
[MC62000(ALL)01/96]
1. Make sure that the headlamp knob is in the
OFF position.
*
[MC62100(ALL)01/96]
2. Lift the hood and find the bulb in the
headlamp socket.
[MC62200(ALL)01/96]
3. Remove the electrical connector from the
bulb housing by pushing the locking tabs on
either side and pulling out the connector.
[MC62300(ALL)01/96]
4. Remove the retaining ring by turning it 1/8
of a turn to free it from the socket. Then
slide the ring off.Keep the ring.You must
use it again to hold the new bulb in place.
[MC62400(ALL)01/96]
5. Remove the rubber boot. Save it because
you'll need it to cover the new bulb.
[MC62500(ALL)01/96]
6. Release the metal retaining clip that holds
the bulb in place.
[MC62600(ALL)01/96]
7. Carefully remove the bulb assembly from its
socket by gently pulling the assembly
rearward without turning.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

188
*
[MC62900(ALL)01/97]
Installing the headlamp bulb
[MC62950(ALL)01/96]
1. Insert the glass end of the bulb assembly
into the socket.
[MC63000(ALL)01/96]
2. Secure the bulb assembly in place with the
metal retaining clip.
[MC63100(ALL)01/96]
3. Attach the rubber boot over the bulb
assembly.
[MC63200(ALL)01/96]
4. Slip the bulb retaining ring over the boot
and bulb assembly. Lock the ring into the
socket by rotating it clockwise until you feel
a ªstopº.
[MC63300(ALL)01/96]
5. Push the electrical connector into the rear of
the bulb assembly until it locks into position.
[MC63400(ALL)01/96]
6. Turn the headlamps on and make sure they
work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

190 [MC63460(ALL)04/96]
half page art:0032288-A
[MC63465(ALL)04/96]
5. Turn the socket counterclockwise to remove
it from the lens.
[MC63470(ALL)04/96]
6. Remove the bulb from the socket by pushing
it in and turning it counterclockwise.
[MC63475(ALL)04/96]
7. Install the bulb by pushing it into the socket
and turning it clockwise.
[MC63480(ALL)04/96]
8. Install the socket by pushing it into its
housing and turning it clockwise.
[MC63485(ALL)04/96]
9. Replace the rear lamp.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997