1997 FORD ASPIRE turn signal

27 %
*
[AS28400(ALL)01/96]
Clock Operation
*
[AS28500(ALL)08/95]
How to view the clock mode
*
[AS28600(ALL)08/95]
Press the ªCLOCKº button to alternate the
frequency and time in the display. In the clock
mode, pressing any radio function will
automatically display the radio frequency for
approximately ten seconds before changing back
to the clock mode.
*
[AS28800(ALL)08/95]
How to set the clock
*
[AS28900(ALL)08/95]
1. Turn the radio on.
*
[AS29050(ALL)04/96]
2. Press and hold in the ªCLOCKº button.
Press the ªSEEKº button left (
b) to advance
the hours and right (
a) to advance the
minutes.
*
[AS29200(ALL)09/95]
NOTE: The clock displays 12-hour time with
no AM/PM indications.
[AS29300(ALL)04/96]
NOTE: If the vehicle's battery is disconnected,
the clock will need to be reset.
%*
[AS35200(ALL)08/95]
Common Radio Reception Conditions
*
[AS35300(ALL)08/95]
Several conditions prevent FM reception from
being completely clear and noise-free, such as
the following:
*
[AS35400(ALL)08/95]
1. Distance/Strength
*
[AS35500(ALL)08/95]
The strength of the FM signal is directly related
to the distance the signal must travel. The
listenable range of an average FM signal is
approximately 25 miles (40 kilometers). Beyond
this distance, the radio is operating in a fringe
area and the signal becomes weaker.
File:04icasf.ex
Update:Tue Mar 4 08:51:43 1997

28
*
[AS35550(ALL)04/96]
NOTE: Always make sure your antenna is
fully extended to the maximum length
for proper reception. If your antenna is
not fully extended, you may experience
signal loss while traveling in fringe
reception areas.
*
[AS35600(ALL)08/95]
2. Terrain
*
[AS35700(ALL)08/95]
The terrain (hilly, mountainous, tall buildings) of
the area over which the signal travels may
prevent the FM signal from being noise-free.
*
[AS35900(ALL)08/95]
If there is a building or large structure between
the antenna and station, some of the signal
ªbendsº around the building, but certain spots
receive almost no signal. Moving out of the
ªshadowº of the structure will allow the station
to return to normal.
*
[AS36000(ALL)08/95]
When the radio waves are reflected off objects or
structures, the reflected signal cancels the normal
signal, causing the antenna to pick up noise and
distortion. Cancellation effects are most
prominent in metropolitan areas, but also can
become quite severe in hilly terrain and
depressed roadways.
*
[AS36100(ALL)08/95]
To minimize these conditions, a stereo/mono
blend circuit has been incorporated into this
system. This feature automatically switches a
weak stereo signal to a clearer monaural signal,
which improves the quality of reception.
*
[AS36200(ALL)08/95]
Several sources of static are normal conditions
on AM frequencies. These can be caused by
power lines, electric fences, traffic lights and
thunderstorms.
File:04icasf.ex
Update:Tue Mar 4 08:51:43 1997

29
*
[AS36300(ALL)08/95]
Another reception phenomenon isStrong Signal
Capture and Overload. This can occur when
listening to a weak station and when passing
another broadcast tower. The close station may
capture the more distant station, although the
displayed frequency does not change. While
passing the tower, the station may switch back
and forth a few times before returning to the
original station.
*
[AS36400(ALL)03/96]
When several broadcast towers are present
(common in metropolitan areas), several stations
may overload the receiver, resulting in
considerable station changing, mixing and
distortion.
*
[AS36500(ALL)08/95]
Automatic gain control circuitry for both AM
and FM bands has been incorporated into this
system to reduce strong signal capture and
overload.
%
*
[AS36600(ALL)08/95]
All About Radio Frequencies
*
[AS36700(ALL)08/95]
The Federal Communications Commission (FCC)
and the Canadian Radio Telecommunications
Commission (CRTC) establish the frequencies
that AM and FM radio stations may use for
their broadcasts. The allowable frequencies are,
AM: 530, 540...1600, 1610 kHz in 10 kHz steps;
FM: 87.9, 88.1...107.7, 107.9 MHz in 0.2 MHz
steps.
*
[AS36800(ALL)08/95]
Not all frequencies will be assigned to a given
area. This radio will tune to each of these
frequencies using manual tune and no fine
tuning is necessary as radio stations may not use
other frequencies.
File:04icasf.ex
Update:Tue Mar 4 08:51:43 1997

45
*
[CF30620(ALL)01/96]
If your key is stuck in the LOCK position and
will not turn, move your steering wheel left or
right until the key turns freely.
[CF30630(ALL)01/96]
If your vehicle has a manual transaxle, you must
push the key toward the steering column to
rotate the switch to the LOCK position.
*
[CF30650(ALL)01/96]
ACC (accessory) allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
*
[CF30660(ALL)01/96]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[CF30680(ALL)01/96]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
%
*
[CF32000(ALL)01/96]
Hazard Flasher Switch
[CF32100(ALL)02/96]
The hazard flasher switch is located on the top
of the steering column. For more information,
refer toHazard Flasherin theRoadside Emergencies
chapter.
%
*
[CF34000(ALL)02/96]
The Turn Signal Lever
*
[CF35000(ALL)02/96]
You can use the turn signal lever on the left side
of the steering column to:
*
[CF35020(ALL)02/96]
q
operate the headlamps and parking lamps
*
[CF35030(ALL)02/96]
q
operate the turn signals and cornering lamps
*
[CF35050(ALL)03/96]
q
turn the high beams on/off
*
[CF35060(ALL)03/96]
q
flash the lamps
File:05iccff.ex
Update:Tue Mar 4 08:52:57 1997

46
*
[CF36000(ALL)02/96]
Headlamps and Parking Lamps
*
[CF36100(ALL)02/96]
To turn the parking lamps or headlamps on,
twist the knob at the end of the turn signal
lever.
[CF36200(ALL)01/96]
FIRST STOP Ð Turning the knob to the first
stop will turn on the license plate lamps,
parking lamps, side marker lamps, tail lamps,
and instrument panel lamps.
[CF36300(ALL)01/96]
SECOND STOP Ð Turning the knob to the
second stop will turn on the headlamps, license
plate lamps, parking lamps, side marker lamps,
tail lamps, and instrument panel lamps.
[CF36400(ALL)01/96]
quarter page art:0032172-A
Headlamp and parking lamp control
%*
[CF36450(ALL)03/96]
Daytime Running Light System
*
[CF36500(ALL)03/96]
(Canadian vehicles only)
*
[CF36600(ALL)04/96]
In Canada, the lights illuminate during daytime
operation. The Daytime Running Light system
(DRL) automatically illuminates when the
ignition switch is turned to the ON position. The
daytime running lights are switched off under
the following conditions:
*
[CF36620(ALL)01/96]
q
when the headlamps are switched on
*
[CF36630(ALL)01/96]
q
when the parking brake is applied
*
[CF36640(ALL)01/96]
q
when the flash-to-pass system is used
File:05iccff.ex
Update:Tue Mar 4 08:52:57 1997

47
*
[CF36700(ALL)03/96]
WARNING
The Daytime Running Light (DRL) system
will not illuminate the tail lamps and
parking lamps. Turn on your headlamps
at dusk. Failure to do so may result in a
collision.
*
[CF36800(ALL)08/95]
High Beams and Flashing the Lamps
*
[CF36900(ALL)01/96]
To turn on the high beams, turn the headlamp
control knob to the headlamp ON position and
push the turn signal lever away from you until
it latches. When the high beams are ON, the
high beam indicator light on the instrument
panel comes on.
*
[CF36950(ALL)01/96]
To turn off the high beams, pull the lever
toward you until it latches. The high beam
indicator light turns off.
%*
[CF36970(ALL)01/96]
Flashing the Lights
*
[CF37000(ALL)01/96]
To flash the headlamps, pull the lever toward
you for a moment and then release it. The
headlamps will flash whether the headlamp
knob is in the on or off position.
[CF37100(ALL)01/96]
quarter page art:0032173-B
High beam and flash-to-pass operation
File:05iccff.ex
Update:Tue Mar 4 08:52:57 1997

48 %
*
[CF37200(ALL)01/96]
Turn Signals
*
[CF37300(ALL)01/96]
Move the lever up to signal a right turn. Move
it down to signal a left turn. The corresponding
indicator light in the instrument cluster will
flash.
[CF37400(ALL)01/96]
If the turn signal stays on after you turn, move
the lever back to the center off position.
[CF37500(ALL)01/96]
For lane changes, move the lever far enough to
signal but not to latch. The lever will return to
the OFF position when you release it.
[CF37600(ALL)01/96]
one third page art:0032175-A
Turn signal
%*
[CF37700(ALL)01/96]
Windshield Wipers and Washer
*
[CF37800(ALL)01/96]
To operate the windshield wipers and washers,
make sure your ignition key is turned to the ON
position.
[CF37900(ALL)01/96]
The windshield wipers can be operated by
moving the control lever. The standard wipers
have two speeds and the optional wipers have
three speeds.
[CF37950(ALL)01/96]
To operate the standard wipers, pull the lever
down to the first stop (LO). For high speed
operation, pull the lever down to the second
stop (HI).
File:05iccff.ex
Update:Tue Mar 4 08:52:57 1997

121
Roadside Emergencies
%*
[ER00500(ALL)03/96]
Hazard Flasher
*
[ER00700(ALL)01/96]
To alert other drivers to hazardous situations,
press the hazard flasher switch on the top of the
steering column. All the turn signals will flash
on and off at the same time. The flashers will
also operate while the brake pedal is applied. To
turn the flashers off, press the switch again.
*
[ER00800(ALL)01/96]
The flashers work whether your vehicle is
running or not. The flashers will work for up to
two hours when the battery is fully charged and
in good condition. They will not drain the
battery excessively unless they are left on for an
extended period of time.
[ER00900(ALL)01/96]
quarter page art:0032174-B
Hazard flasher switch
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997