101 [TO09550(ALL)01/96]
half page art:0032161-C
The location of the fuel pump shut-off switch (U.S. vehicle
shown Ð Canadian vehicles similar)
*
[TO09600(ALL)03/96]
WARNING
If you see or smell fuel, do not reset the
switch or try to start your vehicle. Have
all the passengers get out of the vehicle
and call the local fire department or a
towing service.
[TO09650(ALL)02/96]
If your engine cranks but does not start after a
collision or major jolt:
*
[TO09700(ALL)03/96]
1. Turn the key in the ignition to the LOCK
position.
*
[TO09750(ALL)03/96]
2. Check under the vehicle for leaking fuel.
[TO09800(ALL)01/96]
3. If you do not see or smell fuel, remove the
door covering the fuel pump shut-off switch
compartment by pressing the tab toward the
rear seat. Push down the red reset button on
the fuel pump shut-off switch.
File:08ictof.ex
Update:Tue Mar 4 08:54:32 1997
122
*
[ER02985(ALL)01/96]
If the Engine Cranks but Does
Not Start or Starting After a
Collision
*
[ER02990(ALL)02/96]
If the engine cranks but does not start or if you
have had a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device that stops the fuel pump
when your vehicle has been involved in a
substantial jolt.
*
[ER02995(ALL)03/96]
For information on how to check and reset the
fuel pump shut-off switch, seeFuel pump shut-off
switchin the Index.
%
*
[ER03000(ALL)01/96]
Fuses
[ER03005(ALL)01/96]
Fuses protect your vehicle's electrical system
from overloading. If electrical parts in your
vehicle are not working, the system may have
been overloaded and blown a fuse. Before you
replace or repair any electrical parts, check the
appropriate circuit protectors.
[ER03010(ALL)04/96]
The following charts tell you which fuses protect
each electrical part of your vehicle. If a fuse
blows, all the parts of your vehicle that use the
circuit will not work.
*
[ER03015(ALL)01/96]
Once you have determined which fuses to check,
follow the procedures underChecking and
replacing fuseslater in this chapter.
[ER03020(ALL)04/96]
Your vehicle has a main fuse block under the
hood and a regular fuse box mounted in the
instrument panel behind a cover.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997
183
*
[MC48600(ALL)01/96]
By law, anyone who manufactures, repairs,
services, sells, leases, trades vehicles, or
supervises a fleet of vehicles is not permitted to
intentionally remove an emission control device
or prevent it from working. In some of the
United States and in Canada, vehicle owners
may be liable if their emission control device is
removed or is prevented from working.
*
[MC48700(ALL)08/95]
Never use a metal exhaust collector when you
service your vehicle. If the metal collector
contacts any of your vehicle's plastic trim or
bumper parts they could melt or deform.
*
[MC48800(ALL)01/96]
Do not drive your vehicle if it does not operate
properly. See your dealer if the engine runs on
for more than five seconds after you shut it off
or if it misfires, surges, stalls, or backfires.
%*
[MC48900(ALL)01/96]
Information about your vehicle's emission
control system is on the Vehicle Emission
Control Information decal located on or near the
engine. This decal identifies engine displacement
and gives some tune-up specifications.
%*
[MC48910(ALL)03/96]
How to Prepare Your Vehicle for
Inspection/Maintenance (I/M) Testing
[MC48920(ALL)02/97]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the
On-Board Diagnostic (OBD) II system. If your
ªCheck Engineº light is on, reference the ªCheck
Engineº light description under the Warning
Lights and Gauges section. Your vehicle may not
pass an I/M test with the Check Engine light on.
If the vehicle's powertrain system or its battery
has just been serviced, the OBD II system is
reset to a not ready for for I/M testing
condition. To prepare for I/M testing, additional
mixed city and highway driving to complete the
check of the OBD II system is necessary.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997