1997 FORD AEROSTAR lock

217
*
[ER15420(ALL)03/96]
When one of the back wheels is off the ground,
the transmission alone will not prevent the
vehicle from moving or slipping off the jack,
even if the vehicle is in P (Park). To prevent the
vehicle from moving when you change a tire, be
sure the parking brake is set, then block the
wheel (both directions) that is diagonally
opposite (other side and end of the vehicle) to
the tire being changed.
*
[ER15430(ALL)03/96]
RWARNING
If the vehicle slips off the jack, you or
someone else could be seriously injured.
*
[ER15550(ALL)01/96]
2. Get out the spare tire and jack.
[ER15600(ALL)01/96]
The jack, jack handle and lug nut wrench are
stowed separately on the left hand wheelhouse
inner panel on standard length models. And in
the right rear storage compartment on extended
length models.
[ER15700(ALL)01/96]
one third page art:0020285-A
Jack stowage
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

218 [ER15750(ALL)01/96]
half page art:0020269-BAerostar extended model jack pack
*
[ER16800(ALL)01/96]
3. Use the tapered end of the lug nut wrench
to unscrew wheel ornaments attached by
retaining screws. Remove any wheel trim.
Insert the tapered end of the lug nut wrench
behind wheel covers or hubcaps and twist
off.
*
[ER16900(ALL)01/96]
4. Loosen the wheel nuts by pulling up on the
handle of the lug nut wrench about one-half
turn (counterclockwise). Do not remove the
wheel lug nuts until you raise the tire off the
ground.
[ER17000(ALL)01/96]
5. Unfold the jack handle and lock into the
jack. Use the jack handle to slide the jack
under the vehicle.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

219 %
*
[ER17100(ALL)01/96]
Removing and Replacing the Tire
%*
[ER17300(ALL)01/96]
1. Positioning the jack
[ER17400(ALL)01/96]
a. To raise a front wheel, place the jack
under a horizontal portion of the
underbody member behind the wheel, as
shown.
[ER17500(ALL)01/96]
one third page art:0020293-A
Front jacking point
[ER17600(ALL)01/96]
b. To raise a rear wheel, place the jack
under a horizontal portion of the
underbody member ahead of the wheel
as shown.
[ER17700(ALL)01/96]
one third page art:0020294-A
Rear jacking point
[ER17800(ALL)01/96]
c. Turn the jack handle clockwise until the
wheel is completely off the ground.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

220 [ER17900(ALL)01/96]
RWARNING
Never place the jack under the rocker
panels.
*
[ER21151(ALL)01/96]
one third page art:0020939-B
*
[ER21400(ALL)01/96]
2. Remove the lug nuts with the lug nut
wrench.
*
[ER21500(ALL)01/96]
3. Replace the flat tire with the spare tire.
*
[ER21700(ALL)01/96]
4. Thread the lug nuts on the wheel studs with
the beveled face toward the wheel. Use the
lug nut wrench to screw the lug nut snug
against the wheel but do not tighten.
*
[ER22200(ALL)03/96]
5. Lower the vehicle by turning the jack handle
counterclockwise.
*
[ER22300(ALL)01/96]
6. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

221 % [ER22400(ALL)04/96]
quarter page art:0020312-B
Lug nut tightening sequence
*
[ER23400(ALL)01/96]
RWARNING
Never use wheels or lug nuts different
than the original equipment as this could
damage the wheel or mounting system.
This damage could allow the wheels to
come off while the vehicle is being
driven.
*
[ER23500(ALL)01/96]
7. Replace any wheel covers, ornaments, or hub
caps that your vehicle has. Make sure that
they are screwed or snapped into place.
[ER23625(ALL)01/96]
8. Put the tire, jack, and wrench away. Make
sure jack is securely fastened so it doesn't
rattle when you drive. The carrier is
designed to hold the temporary spare which
comes with your vehicle. The stowage of a
full size tire in the spare tire carrier may
damage the tire or the vehicle. The flat full
size tire should be stowed securely in the
vehicle until it can be repaired.
*
[ER23700(ALL)03/96]
9. Unblock the wheels.
*
[ER23800(ALL)03/96]
Retighten the wheel lug nuts to the specified
torque at 500 miles (800 km) of new vehicle
operation and at intervals specified in the
Maintenance Schedulebooklet.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

231
*
[MC02500(ALL)01/96]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[MC02600(ALL)01/96]
Working with the engine off:
*
[MC02650(ALL)01/96]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[MC02700(ALL)01/96]
2. Remove the key from the ignition after you
turn the engine off.
*
[MC02725(ALL)01/96]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC02750(ALL)01/96]
Working with the engine on:
*
[MC02785(ALL)01/96]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[MC02800(ALL)01/96]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC02900(ALL)01/96]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
%*
[MC02950(ALL)02/96]
Opening the Hood
*
[MC03000(ALL)01/96]
1. Pull the hood release handle, located next to
the parking brake pedal.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

242 [MC08785(ALL)01/96]1. Before you remove the cap, turn the engine
off and let it cool.
[MC08790(ALL)01/96]
2. When the engine is cool, wrap a thick cloth
around the cap and turn it slowly,
counterclockwise to the first stop.
*
[MC08800(ALL)05/96]
3. Step back while the pressure releases.
*
[MC08810(ALL)05/96]
4. When you are sure that all the pressure has
been released, use the cloth to press the cap
down, turn it counterclockwise, and remove
it.
[MC08815(ALL)01/96]
UseFord Premium Engine Coolant
E2FZ-19549-AA(in Canada, Motorcraft CXC-8-B)
or an equivalent premium engine coolant that
meets Ford specification ESE-M97B44-A. Ford
Premium Engine Coolant is an optimized
formula that will protect all metals and rubber
elastomers used in Ford cooling systems for 4
years or 50,000 miles (80,000 km).
*
[MC08820(ALL)05/96]
Do not use alcohol or methanol antifreeze or any
engine coolants mixed with alcohol or methanol
antifreeze. Do not use supplemental coolant
additives in your vehicle. These additives may
harm your engine cooling system.The use of an
improper coolant may void the warranty of
your vehicle's engine cooling system.
*
[MC08825(ALL)05/96]
Recycled engine coolant
*
[MC08830(ALL)05/96]
Ford Motor Company recommends that Ford
and Lincoln-Mercury dealers use recycled engine
coolant produced by Ford-approved processes.
Not all coolant recycling processes produce
coolant which meets Ford specification
ESE-M97B44-A, and use of such coolant may
harm engine and cooling system components.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

262 [MC35710(ALL)05/96]
half page art:0095076-BFuel filler door override handle
%*
[MC35720(ALL)01/96]
Removing the fuel cap
*
[MC35730(ALL)01/96]
The proper instructions for removing the fuel
cap are as follows:
*
[MC35740(ALL)01/96]
q
Unscrew the fuel cap by exerting pressure on
the plastic lock bar and rotating the fuel cap
counterclockwise.
*
[MC35750(ALL)01/96]
q
Turn the fuel cap 1/2 to 3/4 of a turn until a
hissing sound is heard. When the hissing
sound stops, continue rotating
counterclockwise to remove the fuel cap.
*
[MC35760(ALL)01/96]
q
Make sure that you follow the above fuel cap
removal instructions and use caution. Such
caution will minimize the possibility of fuel
spraying during removal of the fuel cap.
*
[MC35770(ALL)03/96]
To replace and secure the fuel cap, place it in
position and rotate it clockwise until it clicks
(ratchets). Doing so will not damage or break
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996