1997 FORD AEROSTAR brake

247
level without having to drive 20 miles to obtain
a normal operating temperature if outside
temperatures are above50ÊF (10ÊC).
*
[MC10120(ALL)01/96]
NOTE: If the vehicle has been operated for an
extended period at high speeds or in
city traffic during hot weather, or
pulling a trailer, the vehicle should be
turned off for about 30 minutes to
allow the fluid to cool before checking.
%*
[MC10130(ALL)01/96]
Checking the Automatic Transmission
Fluid
[MC10140(ALL)05/96]
With the vehicle on a level surface, start the
engine and move the gearshift lever through all
of the gear ranges allowing sufficiant time for
each position to engage. Securely latch the
gearshift lever in the P (Park) position, fully set
the parking brake and leave the engine running.
*
[MC10150(ALL)01/96]
RWARNING
Your vehicle should not be driven if the
fluid level is below the bottom hole on
the dipstick and outside temperatures are
above50ÊF (10ÊC).
[MC10160(ALL)01/96]
Wipe off the dipstick cap (located toward the
passenger's side of the engine), pull the dipstick
out and wipe the indicator end clean. Put the
dipstick back into the filler tube and make sure
it is fully seated. Pull the dipstick out and read
the fluid level.
*
[MC10170(ALL)01/96]
When checking fluid at normal operating
temperature, the fluid level should be within the
crosshatched area on the dipstick. When the
vehicle has not been driven, and outside
temperature is above50ÊF (10ÊC), thefluid level
should be between the holes on the dipstick.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

252
*
[MC24900(ALL)02/96]
Wiper blade replacement
*
[MC25000(ALL)01/96]
If the wiper blades still do not work properly
after you clean them, you may need to replace
the wiper blade assembly or the blade element.
When replacing the wiper blade assembly, blade
refill, or wiper arm always use a Motorcraft part
or equivalent. To replace the blades, follow the
instructions that come with them.
%
*
[MC25200(ALL)01/96]
Tires
*
[MC25300(ALL)03/96]
Look at your tires each time you fill your fuel
tank. If one tire looks lower than the others,
check the pressure in all of them. Always follow
these precautions:
*
[MC25400(ALL)02/96]
q
Use an accurate tire pressure gauge.
*
[MC25500(ALL)02/96]
q
Check the tire pressure when tires are cold,
after the vehicle has been parked for at least
one hour or has been driven less than 3 miles
(5 km).
*
[MC25600(ALL)03/96]
q
Make sure the weight of your load is evenly
distributed.
*
[MC25700(ALL)03/96]
q
Adjust tire pressure to recommended
specifications found on the Safety Compliance
Certification Label.
[MC25750(ALL)01/96]
q
Make sure the spare tire is mounted and
anchored properly in the tire carrier without
contacting functional parts such as brake
tubes, fuel lines, exhaust pipes, etc.
*
[MC25800(ALL)03/96]
If you do not take these precautions, your tires
may fail or go flat.
*
[MC25890(ALL)03/96]
Ford Motor Company recommends obeying
posted speed limits.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

260 [MC31625(ALL)01/96]q
Put the chains on tightly with the ends held
down securely. Verify that no chain touches
any wiring, brake lines or fuel lines.
Retighten the chains after driving 1/2 mile
(0.8 km). Follow the chain manufacturer's
instructions.
*
[MC31650(ALL)01/96]
q
Do not drive faster than 30 mph (48 km/h)
or the chain manufacturer's recommended
speed limit, whichever is lower. Avoid
bumps, holes and sharp turns. If you can
hear the chains rub or bang against your
vehicle, remove the chains to prevent damage
to your vehicle.
*
[MC31750(ALL)01/96]
q
Tire chains may affect vehicle handling. Drive
carefully and avoid hard braking.
*
[MC31800(ALL)01/96]
q
Avoid fully loading your vehicle if possible.
*
[MC31900(ALL)01/96]
q
Remove tire chains at the first opportunity
after using them on snow and ice. Do not use
the chains on dry roads.
*
[MC31950(ALL)01/96]
q
Make sure your suspension insulation and
bumpers are not missing or worn to avoid
damage to your vehicle.
%
*
[MC35000(ALL)01/96]
Filling the Fuel Tank
[MC35100(ALL)01/96]
quarter page art:0020347-C
Fuel filler door
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

269
*
[MC37520(ALL)01/96]
The following decrease fuel economy:
*
[MC37530(ALL)01/96]
q
Lack of regular, scheduled maintenance
*
[MC37540(ALL)01/96]
q
Excessive speed
[MC37550(ALL)04/96]
q
Rapid acceleration
*
[MC37560(ALL)01/96]
q
Driving with your foot on the brake
*
[MC37570(ALL)01/96]
q
Sudden stops
*
[MC37580(ALL)01/96]
q
Extended engine idling
*
[MC37590(ALL)01/96]
q
Using speed control in hilly terrain
*
[MC37600(ALL)01/96]
q
Extended use of the A/C, defroster, rear
window defroster and other accessories
*
[MC37610(ALL)01/96]
q
Underinflated tires
*
[MC37620(ALL)01/96]
q
Heavy loads
*
[MC37630(ALL)01/96]
q
Aftermarket add-ons such as bike, ski or
luggage racks, bug deflectors, etc.
%
*
[MC38000(ALL)01/96]
Emission Control System
*
[MC38100(ALL)01/96]
Your vehicle is equipped with a catalytic
converter which enables your vehicle to comply
with applicable exhaust emission requirements.
*
[MC38110(ALL)01/96]
To make sure that the catalytic converter and the
other emission control parts continue to work
properly:
*
[MC38200(ALL)01/96]
q
Use only unleaded fuel.
*
[MC38210(ALL)01/96]
q
Avoid running out of fuel.
*
[MC38220(ALL)01/96]
q
Do not turn off the ignition while your
vehicle is moving, especially at high speeds.
*
[MC38230(ALL)03/96]
q
Have the services listed in yourMaintenance
Schedulebooklet performed according to the
specified schedule.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

272authorized service center can perform a detailed
OBD II drive cycle as it would any other type of
repair work.
%
*
[MC44600(ALL)03/96]
Lights and Bulb Replacement
*
[MC44700(ALL)01/96]
It is a good idea to check the operation of the
following lights frequently:
*
[MC44800(ALL)01/96]
q
headlamps
*
[MC44850(ALL)01/96]
q
high-mount brakelamp
*
[MC44900(ALL)01/96]
q
tail lamps
*
[MC45000(ALL)01/96]
q
brakelamps
*
[MC45100(ALL)01/96]
q
hazard flasher
*
[MC45200(ALL)01/96]
q
turn signals
*
[MC45300(ALL)05/96]
q
license plate lamps
%*
[MC45400(ALL)01/96]
The alignment of your headlamps should be
checked if:
*
[MC45500(ALL)01/96]
q
oncoming motorists frequently signal you to
turn off your vehicle's high beams when you
do not have the high beams on
*
[MC45600(ALL)01/96]
q
the headlamps do not seem to give you
enough light to see clearly at night
*
[MC45700(ALL)01/96]
q
the headlamp beams are pointed substantially
away from a position slightly down and to
the right
%*
[MC45800(ALL)01/96]
Headlamp Bulb
*
[MC45900(ALL)03/96]
The headlamps on your vehicle use replaceable
bulbs. When the lamp burns out, simply replace
the bulb, rather than the whole lamp.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

275 [MC47150(ALL)01/96]
2. Snap the retaining wire over both sides of
the bulb and connect the electrical connector.
[MC47275(ALL)01/96]
3. Position the headlamp on the vehicle and
install the four attaching screws.
*
[MC47300(ALL)01/96]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
[MC47310(ALL)01/96]
Removing the High-Mount Brakelamp
Bulb
[MC47315(ALL)01/96]
Liftgate models
[MC47317(ALL)01/96]
To remove the brakelamp and bulb:
*
[MC47330(ALL)01/96]
1. Remove the two screws from the surface of
the lens.
*
[MC47340(ALL)01/96]
2. After removing the screws, remove the lamp
assembly.
[MC47353(ALL)01/96]
3. Disconnect the high-mount brakelamp wiring
connector.
[MC47356(ALL)01/96]
4. Remove the screw retaining the bulb holder
assembly, pull the bulb holder assembly
away from the lamp, and pull the bulb
straight out of the holder.
[MC47360(ALL)04/96]
To replace/install the brakelamp:
[MC47367(ALL)01/96]
1. Push bulb(s) into bulb holder assembly.
[MC47373(ALL)01/96]
2. Place bulb holder assembly on lamp and
install retaining screw. Tighten screw.
[MC47376(ALL)01/96]
3. Connect the high-mount brakelamp wiring
connector.
[MC47377(ALL)01/96]
4. Position the lamp assembly on the vehicle.
[MC47378(ALL)01/96]
5. Install and tighten the two screws.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

276 [MC47380(ALL)01/96]6. Apply brakes to confirm the brakelamp is
functional after installing.
[MC47381(ALL)01/96]
half page art:0095018-A
Replacing the high-mount brakelamp bulb Ð liftgate
models only
[MC47383(ALL)01/96]
Dual Rear Door Models
*
[MC47384(ALL)01/96]
To remove the brakelamp:
*
[MC47385(ALL)01/96]
1. Remove the two screws from the surface of
the lens.
[MC47386(ALL)01/96]
2. Pull the lens assembly out of the lamp
housing.
[MC47387(ALL)01/96]
3. Pull the bulb socket out of the lens assembly.
It is not necessary to twist the socket.
[MC47388(ALL)01/96]
4. Pull the bulb out of the socket.
[MC47389(ALL)04/96]
To replace/install the brakelamp:
[MC47396(ALL)01/96]
1. Push the bulb into the socket.
[MC47397(ALL)01/96]
2. Push the socket into the lens assembly.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

277 [MC47398(ALL)01/96]
3. Install the lens assembly into lamp.
[MC47399(ALL)01/96]
4. Install and tighten the two screws.
[MC47400(ALL)01/96]
half page art:0021006-A
Replacing the high-mount brakelamp bulb Ð dual rear
door models only
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996