1997 DODGE NEON battery

Downloaded from www.Manualslib.com manuals search engine 8W-47 AUDIO SYSTEMS
INDEX
page page
DESCRIPTION AND OPERATION
HELPFUL INFORMATION.................. 5
RADIO ILLUMINATION.................... 5RADIO MEMORY........................ 5
RADIO OPERATION...................... 5
SPEAKERS............................. 5
DESCRIPTION AND OPERATION
RADIO OPERATION
When the ignition switch is in either the ACCES-
SORY or RUN position, it connects circuit A1 from
the Power Distribution Center (PDC) to circuit A31.
Circuit A31 powers a bus bar in the fuse block. The
bus bar feeds two circuits, one of which is circuit
X12. Circuit X12 powers the radio. A 10 amp fuse, in
cavity 16 of the fuse block, protects circuit X12.
Circuit Z9 supplies the ground path for the radio.
The grounding point for circuit Z9 is the instrument
panel right center support.
RADIO MEMORY
Circuit M1 from the Power Distribution Center
(PDC) supplies power for the radio memory. The cir-
cuit contains the Ignition Off Draw (IOD) fuse. The
IOD fuse is removed during vehicle shipping to pre-
vent excessive battery draw.
RADIO ILLUMINATION
When the parking lamps or headlamps are ON, cir-
cuits E2 and L7 power the radio illumination lamps
and park lamps. Circuit E2 feeds the illumination
lamp. Circuit L7 feeds the park lamps of the radio.
Circuit F33 feeds circuit L7.
A 4 amp fuse, in cavity 12 of the fuse block, pro-
tects circuit E2. A 15 amp fuse, in cavity 2 of the fuse
block, protects circuits L7 and F33.
SPEAKERS
Circuit X53 feeds the speaker in the left front door.
Circuit X55 is the return from the speaker to the
radio. On the premium system the X53 and X55 cir-
cuits are connected in with the instrument panel
speaker.
Circuit X54 feeds the speaker in the right front
door. Circuit X56 is the return from the speaker to
the radio. On the premium system the X54 and X56
circuits are connected in with the instrument panel
speaker.
Circuit X51 feeds the left rear speaker. Circuit X57
is the return from the speaker to the radio.Circuit X52 feeds the right rear speaker. Circuit
X58 is the return from the speaker to the radio.
HELPFUL INFORMATION
²Circuit M1 also powers the vanity lamps, glove
box lamp, time delay relay, dome lamps, underhood
lamp, cargo lamp, and power mirrors.
²If the radio does not operate, check for blown
fuses in circuits A1 and X12.
²Circuits A3, and F33 feed the L7 circuit.
²If the radio illumination lamps do not operate,
check for blown fuses in circuits E2, F33, and A3.
PL8W - 47 AUDIO SYSTEMS 8W - 47 - 5

Downloaded from www.Manualslib.com manuals search engine 8W-50 FRONT LIGHTING
INDEX
page page
GENERAL INFORMATION
INTRODUCTION......................... 7
DESCRIPTION AND OPERATION
FOG LAMPS (FRONT).................... 8HEADLAMP LEVELING MOTORS............ 8
HEADLAMPS........................... 7
PARKING LAMPS........................ 7
GENERAL INFORMATION
INTRODUCTION
The headlamp switch has 3 positions, ON, PARK
(parking lights) and OFF. Two circuits, L2 and L20
connect the headlamp switch to the headlamp dim-
mer/optical horn switch located in the multi-function
switch. The multi-function switch feeds the low and
high beams of the headlamps.
DESCRIPTION AND OPERATION
PARKING LAMPS
Circuit A3 in the Power Distribution Center (PDC)
connects to a bus bar in the fuse block. One of the
four circuits powered by the bus bar is circuit F33.
Circuit F33 connects to the headlamp switch. A 40
amp fuse in the PDC protects the A3 circuit. A 15
amp fuse, in cavity 2 of the fuse block, protects the
F33 circuit.
The headlamp switch has 3 positions, ON, PARK
(tail lamps) and OFF, plus a dimmer switch. When
the headlamp switch is in the PARK or ON position,
the switch connects circuit F33 to circuit L7. From
the headlamp switch, circuit L7 branches to power
the front parking lamps and rear tail lamps, lavalier
lamps, side marker lamps, and rear license plate
lamp.
GROUND CIRCUIT
Circuit Z1 provides ground for the parking lamps,
headlamps, lavalier lamps, tail lamps, side marker
lamps and rear license plate lamp although different
grounding points are used. Circuit Z1 also provides
the ground path for the headlamps and turn signals.
HELPFUL INFORMATION
²Check for a blown 40 amp fuse in the PDC.
²Check for a blown fuse in cavity 2 of the fuse
block.
²For the left front parking lamp, turn signal, side
marker lamp and left headlamp, the Z1 circuitgrounding point is the left side of the radiator closure
panel.
²For the right front parking lamp, turn signal,
side marker lamp and right headlamp, the Z1 circuit
grounding point is in the right fender side shield.
²Circuit L7 also feeds the radio, if equipped.
²When the headlamp switch is in the PARK or
ON position, the dimmer circuit, F33, also connects
to circuit E1. Circuit E1 powers the ash receiver
lamp, transmission range indicator lamp, instrument
panel cluster illumination lamps, HVAC control
lamp, heated rear window lamp, and radio lamp. A 4
amp fuse, in cavity 12 of the fuse block, protects cir-
cuit E1.
HEADLAMPS
The headlamp switch has 3 positions, ON, PARK
(parking lights) and OFF. Two circuits, L2 and L20
connect the headlamp switch to the headlamp dim-
mer/optical horn switch located in the multi-function
switch. The multi-function switch feeds the low and
high beams of the headlamps.
HEADLAMP SWITCH IN OFF OR PARKING
LAMP POSITION
Circuit A3 originates in the Power Distribution
Center (PDC) and supplies battery voltage for the
headlamp switch. A 40 amp fuse protects the A3 cir-
cuit. The headlamp switch has an internal 24 amp
circuit breaker that connects circuit A3 to either the
L2 or L20 circuits, depending on switch position.
In the OFF and PARK positions the headlamp
switch feeds the L20 circuit that connects to the
multi-function switch. Circuit L20 powers the high
beam circuit when the operator flashes the head-
lamps with the turn signal stalk of the multi-func-
tion switch. When the operator flashes the
headlamps with the stalk, the multi-function switch
connects the L20 circuit to the L3 circuit. The L3 cir-
cuit feeds the high beam of the headlamps.
HEADLAMP SWITCH IN ON POSITION
When the headlamp switch is in the ON position,
it connects the A3 circuit from the PDC to circuit L2.
PL8W - 50 FRONT LIGHTING 8W - 50 - 7

Downloaded from www.Manualslib.com manuals search engine 8W-52 TURN SIGNALS
INDEX
page page
DESCRIPTION AND OPERATION
HAZARD FLASHERS..................... 5TURN SIGNALS......................... 5
DESCRIPTION AND OPERATION
TURN SIGNALS
Voltage for the turn signals flows from the Power
Distribution Center (PDC) to the ignition switch on
circuit A2. With the key in the RUN position, the
ignition switch connects voltage from the A2 circuit
to the A22 circuit. A 40 amp fuse in the PDC protects
the A2 and A22 circuits.
Circuit A22 connects to a bus bar in the fuse block.
L5 is one of the circuits fed by the bus bar. Circuit
L5 contains a 10 amp fuse and supplies voltage to
the multi-function switch. The multi- function switch
supplies voltage to the combination flashing unit on
circuit L55. Voltage leaves the combination flashing
unit on circuit L32 and flows to the multi-function
switch connector.
RIGHT TURN SIGNAL
When the operator selects the right turn signal,
the multi-function connects power from circuit L32 to
circuits L60 and L62. Circuit L62 connects to the
multi-function switch and feeds the right rear turn
signal/hazard flasher/stop lamp.
Circuit L60 connects to the multi-function switch
and feeds the right front turn signal/hazard flasher
lamp and side marker lamp. Circuit L60 also splices
to power the turn signal indicator lamp on the
instrument cluster.
LEFT TURN SIGNAL
When the operator selects the left turn signal, the
multi-function connects power from circuit L32 to cir-
cuits L61 and L63. Circuit L63 connects to the multi-
function switch and feeds the left rear turn signal/
hazard flasher/stop lamp.
Circuit L61 connects to the multi-function switch
and feeds the left right front turn signal/hazard
flasher lamp and side marker lamp. Circuit L61 also
splices to power the turn signal indicator lamp on the
instrument cluster.
GROUND CIRCUIT
Circuit Z1 provides ground for all the turn signal
lamps, although the it has different grounding pointsfor each turn signal circuit. Circuit Z2 provides the
ground path for the combination flashing unit.
HELPFUL INFORMATION
²For the left front turn signal/hazard flasher
lamp, the Z1 circuit grounding point is the left side of
the radiator closure panel.
²For the right front turn signal/hazard flasher
lamp, the Z1 circuit grounding point is in the right
fender side shield.
²For the left rear turn signal/hazard flasher/stop
lamp, the Z1 circuit grounding point is in the left
rear wheel well.
²For the right rear turn signal/hazard flasher/
stop lamp, the Z1 circuit grounding point is in the
right rear wheel well.
²Circuit Z1 also supplies ground for the head-
lamps, parking lamps, rear license plate lamp,
back-up lamps and side marker lamps.
²The grounding point for circuit Z2 is the instru-
ment panel right center support. Circuit Z2 supplies
ground for the combination flashing unit.
²A 10 amp fuse, in cavity 6 of the fuse block, pro-
tects circuit L5.
²A 40 amp fuse in the PDC protects the A2 and
A22 circuits.
²The bus bar in the fuse block that connects to
circuit A22 and feeds circuit L5 for the turn signals
also powers three other fuse protected circuits. The
other circuits are C1, F20 and F25.
HAZARD FLASHERS
Circuit L9 from the Power Distribution Center
(PDC) supplies battery voltage for the hazard flash-
ers. A 10 amp fuse in the PDC protects circuit L9.
Circuit L9 connects to the multi-function switch.
With the hazard flashers ON, the multi-function
switch connects circuits L9 and L55.
Circuit L55 feeds the combination flashing unit.
Circuit Z2 provides ground for the flashing unit.
From the flashing unit, circuit L32 connects to the
multi-function switch. With the hazard flashers ON,
the multi-function switch connects circuit L32 to cir-
cuits L60, L61, L62, and L63.
PL8W - 52 TURN SIGNALS 8W - 52 - 5

Downloaded from www.Manualslib.com manuals search engine 8W-53 WIPERS
INDEX
page page
DESCRIPTION AND OPERATION
HELPFUL INFORMATION.................. 4WIPERSÐINTERMITTENT................. 4
DESCRIPTION AND OPERATION
WIPERSÐINTERMITTENT
The intermittent windshield wiper system is pow-
ered by a 20 amp fuse located in the fuse block. This
fuse is HOT in the RUN and ACCESORY position.
This system has three modes of operation, INTER-
MITTENT, LOW, and HIGH.
When the ignition switch is in the RUN or ACCE-
SORY position, power is supplied on the F13 circuit
to the windshield wiper switch and wiper motor. The
wiper motor is case grounded and the switch logic
and relay control uses its own ground on the Z2 cir-
cuit to the right instrument panel center support.
When the operator moves the switch to LOW speed
position, battery voltage is passed through the switch
to circuit V3, which connects to the LOW speed
brushes of the wiper motor. If the switch is moved to
the HIGH speed mode of operation, power is
switched to the V4 circuit and to the HIGH speed
brushes of the motor.
When the delay mode of operation is selected cir-
cuits internal to the switch power up the logic and
relay control. The internal control supplies power to
the LOW speed area of the switch (V3 circuit) and
cycles the wipers. The amount of delay between
wiper cycles is dependent on switch position. All
relays and internal logic in the switch are not ser-
viceable and should be replaced as an assembly.As the windshield wiper motor turns, the park
switch internal to the motor moves from its grounded
position to the powered RUN position. When the
wiper switch is turned OFF, the V5 circuit is used to
prevent the wipers from stopping in any position but
park.
The intermittent windshield wiper system is also
equipped with a pulse wipe feature. To activate this
feature the operator presses the washer switch
momentarily. When the washer switch CLOSES, a
voltage signal is sent to the internal logic and relay
control. The control will cycle the wipers. In addition,
the wipers are placed in the maximum delay posi-
tion.
The windshield washer uses a pump motor inside
of the windshield washer fluid reservoir. When the
washer switch is pressed, power is supplied on the
V10 circuit to the pump motor. Ground for the pump
motor is the Z1 circuit and terminates at the left
headlamp ground.
HELPFUL INFORMATION
²Check the 20 amp fuse in cavity 15 of the fuse
block.
²Check the ground strap on the windshield wiper
motor.
²For the intermittent wiper system a ground is
dedicated to the wiper switch.
8W - 53 - 4 8W - 53 WIPERSPL

Downloaded from www.Manualslib.com manuals search engine 8W-61 POWER DOOR LOCKS
INDEX
page page
DESCRIPTION AND OPERATION
HELPFUL INFORMATION.................. 5POWER DOOR LOCKS.................... 5
DESCRIPTION AND OPERATION
POWER DOOR LOCKS
The Power Distribution Center (PDC) supplies
voltage to the fuse block from the 40 amp HEAD-
LAMPS fuse on circuit A3. Fuse 3, a 20 amp located
in the fuse block, supplies battery voltage on the F35
circuit to both door lock switches.
The ground path for the system is through the left
door lock switch on the Z8 circuit. The grounding
point is located at the instrument panel left center
support brace.
LEFT DOOR SWITCH OPERATION (LOCK)
When the door lock switch is moved to the LOCK
position, voltage is supplied on the P35 circuit to the
bus bar located inside the right door switch, lock
side. Battery voltage is passed through the switch to
the P33 circuit to the door motors. Grounding is pro-
vided through the P34 circuit for all door motors
back to the right door switch. The ground is passed
through the bus bar internal to the switch, UNLOCK
side, to the P36 circuit. The P36 circuit connects to
the left front switch to a bus bar, internal to the
switch, and then to the Z8 circuit. The Z8 circuit con-
nects to its grounding point.
LEFT DOOR SWITCH OPERATION (UNLOCK)
When the switch is moved to the UNLOCK posi-
tion, voltage is supplied on the P36 circuit to the
right door switch, unlock side. The battery voltage is
passed through the switch internal bus bar to the
P34 circuit. The P34 circuit then connects to the door
motors on the unlock side. Grounding for the
UNLOCK function is provided by the P33 circuit.
The P33 circuit conects back to the right door
switch, LOCK side, and passes through the internal
bus bar to the P35 circuit. The P35 circuit conects
back to the left door switch, and passes through the
switch to the Z8 circuit. The Z8 circuit goes to it's
grounding point.
RIGHT DOOR SWITCH OPERATION (LOCK)
When the switch is moved to the LOCK position,
voltage is supplied to the P33 circuit, and then to the
door lock motors. The ground path is provided on theP34 circuit back to the right door switch. The ground
is passed through the switch internal bus bar to the
P36 circuit. The P36 circuit connects to the left door
switch and through to the Z8 circuit. The Z8 circuit
then connects to the grounding point at the left cen-
ter instrument panel support.
RIGHT DOOR SWITCH OPERATION (UNLOCK)
When the switch is moved to the UNLOCK posi-
tion voltage is supplied to the P34 circuit from the
switch to the door UNLOCK side of the motors. The
grounding path is through the LOCK side of the
motors, circuit P33, back to the switch. The ground
continues through the internal bus bar of the switch
on circuit P35 to the left door switch. At the left door
switch, the ground passes through that switches
internal bus bar to the Z8 grounding point.
HELPFUL INFORMATION
²Check the 40 amp fuse in the PDC.
²Check the 15 amp fuse in cavity 3 of the fuse
block.
²Check the grounding point on the instrument
panel left center support brace.
PL8W - 61 POWER DOOR LOCKS 8W - 61 - 5

Downloaded from www.Manualslib.com manuals search engine 3232
SENSOR OXYGEN
HEATED
DOWNSTREAMCRANKSHAFT
POSITION
SENSOR
SENSOR OXYGEN
HEATED
UPSTREAM VEHICLE
SPEED
SENSOR
S118
K4
20
BK/LBK4
20
BK/LBK4
20
BK/LBK4
18
BK/LB
K4
18
BK/LB
CAMSHAFT
POSITION
SENSORSENSOR
KNOCK
BATTERY
TEMPERATURE
SENSOR
SENSOR TEMPERATURE
COOLANT
ENGINETHROTTLE
POSITION
SENSOR
122
AA1
K4
20
BK/LB
K4
20
BK/LBK4
20
BK/LBK4
20
BK/LBK4
20
BK/LB
K4
20
BK/LB
10C161
K4
20
BK/RDK4
20
BK/LB
2.0L
SOHC DOHC2.0L
S120
K4
20
BK/LB
S110
SENSOR IAT/
MAP
(8W-30-3)(8W-30-7)
(8W-30-3)(8W-30-8)
(8W-30-7)(8W-30-6)
(8W-30-7)
(8W-30-7)(8W-30-6)
(8W-30-3)
(8W-30-6)
8W - 70 - 2 8W-70 SPLICE INFORMATIONPL-RHD
978W-1PLR07001

Downloaded from www.Manualslib.com manuals search engine 8W-80 CONNECTOR PIN-OUTS
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
Component Page
A/C Compressor Clutch................8W-80-4
A/C Cycling switch...................8W-80-4
A/C-Heater Blower Motor..............8W-80-4
A/C-Heater Control Switch.............8W-80-4
A/C High Pressure Switch..............8W-80-4
A/C Low Ptressure Switch..............8W-80-5
ABS Hydraulic Modulator..............8W-80-5
ABS Relay Box......................8W-80-5
Airbag Control Module................8W-80-5
Ash Receiver lamp...................8W-80-6
Back-Up Lamp Switch (MTX)...........8W-80-6
Battery Temperature Sensor............8W-80-6
Blower Motor Resister Block............8W-80-6
Brake Warning Lamp Switch...........8W-80-6
C101..............................8W-80-7
C102..............................8W-80-7
C103..............................8W-80-7
C105..............................8W-80-8
C108..............................8W-80-8
C160..............................8W-80-8
C161..............................8W-80-8
C203..............................8W-80-9
C205..............................8W-80-9
C206..............................8W-80-9
C225..............................8W-80-9
C230.............................8W-80-10
C231.............................8W-80-10
C241.............................8W-80-10
C301.............................8W-80-11
C303.............................8W-80-11
C309.............................8W-80-11
C315.............................8W-80-11
C323.............................8W-80-11
C324.............................8W-80-11
C325.............................8W-80-12
C340.............................8W-80-12
C341.............................8W-80-12
Camshaft Position Sensor.............8W-80-12
Clockspring........................8W-80-12
Clutch Pedal Position Switch (MTX).....8W-80-12
Controller Anti-Lock Brake............8W-80-13
Crankshaft Position Sensor............8W-80-14
Data Link Connector.................8W-80-14
Dome Lamp........................8W-80-14
Downstream Heated Oxygen Sensor.....8W-80-15Component Page
Driver Side Airbag..................8W-80-15
Duty Cycle Evap/Purge Solenoid........8W-80-15
EGR Transducer solenoid.............8W-80-15
Engine Coolant Temperature
Sensor (ECT).....................8W-80-15
Engine Oil Pressure Switch............8W-80-16
Front Fog Lamp Switch...............8W-80-16
Fuel Injector No.1...................8W-80-16
Fuel Injector No.2...................8W-80-16
Fuel Injector No.3...................8W-80-16
Fuel Injector No.4...................8W-80-16
Fuel Pump Module..................8W-80-17
Generator.........................8W-80-17
Glove Box Lamp and Switch...........8W-80-17
Headlamp Dimmer and Optical
Horn Switch.....................8W-80-17
Headlamp Leveling Switch............8W-80-17
Headlamp Switch...................8W-80-17
Horn No.1.........................8W-80-18
Horn No.2.........................8W-80-18
(IAT/Map) Sensor...................8W-80-18
Idle Air Control Motor (IAC)...........8W-80-18
Ignition Coil Pack...................8W-80-18
Ignition Switch.....................8W-80-19
Immobilizer Engine Sensor............8W-80-19
Immobilizer Sensor..................8W-80-19
Instument Cluster - C1...............8W-80-19
Instument Cluster - C2...............8W-80-19
Intermittent Wipe/Wash Switch........8W-80-20
Key-In Switch......................8W-80-20
Knock Sensor......................8W-80-20
Left Airbag Impact Sensor.............8W-80-20
Left Back-Up Lamp..................8W-80-20
Left Door Lock Switch................8W-80-21
Left Door Window Motor..............8W-80-21
Left Fog Lamp......................8W-80-21
Left Front Door Lock Motor...........8W-80-21
Left Front Door Speaker..............8W-80-21
Left Front Wheel Speed Sensor.........8W-80-22
Left Headlamp.....................8W-80-22
Left Headlamp Leveling Motor.........8W-80-22
Left Instrument Panel Speaker
(Premium).......................8W-80-22
Left License Lamp...................8W-80-22
Left Park/Turn Signal Lamp...........8W-80-22
8W - 80 - 2 8W - 80 CONNECTOR PIN-OUTSPL

Downloaded from www.Manualslib.com manuals search engine 978W-1
PL-RHD 8W - 80 - 6 8W-80 CONNECTOR PIN-OUTS
PLR08006
CAV CIRCUIT FUNCTION
1 E2 22OR FUSED PANEL LAMPS DIMMER SWITCH SIGNAL
2 Z3 20BK/OR GROUND BLACK12
ASH
RECEIVER
LAMP
BACK-UP LAMP
SWITCH (MTX)GRAY
CAV CIRCUIT FUNCTION
A L1 20VT/BK REVERSE LAMP SENSE
B F20 20WT FUSED IGNITION SWITCH OUTPUT (RUN)ABAB
CAV CIRCUIT FUNCTION
1 K4 18BK/LB SENSOR GROUND
2 G31 18VT/LG AMBIENT TEMPERATURE SENSOR SIGNAL
2
1 54
3
CAV CIRCUIT FUNCTION
1 C5 14LG M1 BLOWER MOTOR DRIVER
2 C6 14LB M2 BLOWER MOTOR DRIVER
3Ð Ð
4 C7 14BK/TN HIGH BLOWER MOTOR DRIVER
5 C4 14TN LOW BLOWER MOTOR DRIVER
BLOWER MOTOR
RESISTOR
BLOCK
3 25 4
1BLACK
CAV CIRCUIT FUNCTION
1 G9 20GY/BK RED BRAKE WARNING LAMP DRIVER
2 Z1 20BK GROUND
BRAKE WARNING
LAMP SWITCH
BATTERY
TEMPERATURE SENSOR12
BLACK
BLACK
21