1997 DODGE NEON warning

Downloaded from www.Manualslib.com manuals search engine 8W-30 FUEL/IGNITION SYSTEMS
INDEX
page page
DESCRIPTION AND OPERATION
AUTOMATIC SHUT DOWN RELAY.......... 15
BATTERY FEED........................ 14
BATTERY TEMPERATURE SENSOR......... 18
CAMSHAFT POSITION SENSOR........... 16
CRANKSHAFT POSITION SENSOR......... 16
DATA LINK CONNECTOR................. 15
DUTY CYCLE EVAP/PURGE SOLENOID...... 19
EGR TRANSDUCER (EET) SOLENOID....... 19
ENGINE COOLANT
TEMPERATURE SENSOR............... 16
FUEL INJECTORS....................... 18
FUEL PUMP MOTOR.................... 15
HEATED OXYGEN SENSORS.............. 16
IDLE AIR CONTROL MOTOR.............. 18
IGNITION COIL PACK.................... 18IGNITION SWITCH...................... 14
INTAKE AIR TEMPERATURE SENSOR....... 17
KNOCK SENSOR....................... 17
LOW FUEL DETECT INPUT............... 19
MANIFOLD ABSOLUTE
PRESSURE SENSOR.................. 17
PARK/NEUTRAL POSITION SWITCH INPUT
(3±SPD TRANSMISSION)................ 19
POWER (DEVICE) GROUND............... 14
POWER STEERING PRESSURE SWITCH..... 19
SIGNAL GROUND....................... 14
THROTTLE POSITION SENSOR............ 17
TORQUE CONVERTER CLUTCH SOLENOID
(TCC)............................... 19
VEHICLE SPEED SENSOR................ 15
DESCRIPTION AND OPERATION
IGNITION SWITCH
In the RUN position, the ignition switch connects
circuit A1 from the Power Distribution Center (PDC)
to circuit A21. A 30 amp fuse in the PDC protects cir-
cuits A1 and A21. Circuit A21 feeds a bus bar in the
fuse block. The bus bar feeds circuits G5, F12, and
F15.
²Circuit G5 powers the gauge cluster warning
lamps and the daytime running lamp (DRL) module.
Fuse cavity 11 (5 amp) in the fuse block protects cir-
cuit G5.
²Circuit F12 splices to the Powertrain Control
Module (PCM), duty cycle purge solenoid, EGR sole-
noid, ABS system, and a bus bar in the PDC. The
bus bar in the PDC feeds the coil side of the radiator
fan relay, A/C compressor clutch relay, and the fuel
pump relay. A 15 amp fuse in the fuse block, cavity
10, protects circuit F12.
²Circuit F15 feeds the Airbag Control Module
(ACM). A 10 amp fuse in the fuse block, cavity 9, pro-
tects circuit F15.
BATTERY FEED
Circuit A14 from the Power Distribution Center
(PDC) supplies battery voltage to cavity 46 of the
Powertrain Control Module (PCM). A 20 amp fuse in
the PDC protects circuit A14.
HELPFUL INFORMATION
Circuit A14 connects to a bus bar in the PDC that
the battery feeds. Circuit A14 powers the AutomaticShut Down (ASD) relay and fuel pump relay. The
A14 circuit also splices to the data link connector.
POWER (DEVICE) GROUND
Circuit Z12 connects to cavities 10 and 50 of the
Powertrain Control Module (PCM). The Z12 circuit
provides ground for PCM internal drivers that oper-
ate high current devices like the injectors and igni-
tion coils.
Internal to the PCM, the power (device) ground cir-
cuit connects to the PCM sensor return circuit (from
circuit K4) and the signal ground circuit (Z11).
HELPFUL INFORMATION
Circuit Z12 which supplies ground for the PCM
high current drivers, has the same termination point
as circuit Z11. The termination point is the left side
of the radiator closure panel.
If the system loses ground for the ganged circuits,
at the left side of the radiator closure panel, the vehi-
cle will not operate. Check the connection at the
ganged ground circuit eyelet.
SIGNAL GROUND
The signal ground circuit Z11 connects to cavity 47
of the PCM. The Z11 circuit provides ground for the
sensors that provide inputs to the PCM. Internal to
the PCM, the signal ground circuit connects to the
PCM sensor return circuit (from circuit K4) and the
power (device) ground circuit (Z12).
The termination point for circuit Z11 is an eyelet
attached to the left side of the radiator closure panel.
8W - 30 - 14 8W - 30 FUEL/IGNITION SYSTEMSPL

Downloaded from www.Manualslib.com manuals search engine 8W-35 ANTI-LOCK BRAKES
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION.......................................................... 6
Component Page
ABS Hydraulic Modulator..............8W-35-4
ABS Pump Motor....................8W-35-3
ABS Pump Motor Relay.............8W-35-2, 3
ABS Relay Box....................8W-35-2, 3
ABS System Relay...................8W-35-2
ABS Warning Lamp..................8W-35-2
Controller Anti-Lock Brake.......8W-35-2, 3, 4, 5
Data Link Connector..................8W-35-3
Fuse 10 (FB)........................8W-35-2
Fuse 10 (PDC).......................8W-35-3
Fuse 25 (PDC).......................8W-35-4
Fuse Block.........................8W-35-2
G101..........................8W-35-2, 3, 4
G102..............................8W-35-4Component Page
Instrument Cluster...................8W-35-2
Left Front Wheel Speed Sensor..........8W-35-5
Left Rear Wheel Speed Sensor..........8W-35-5
Power Distribution Center...........8W-35-3, 4
Pump Motor Driver...................8W-35-3
Right Front Wheel Speed Sensor........8W-35-5
Right Rear Wheel Speed Sensor.........8W-35-5
S101..............................8W-35-4
S103..............................8W-35-3
S104..............................8W-35-4
S108..........................8W-35-2, 3, 4
S109..............................8W-35-2
S210..............................8W-35-3
Stop Lamp Switch....................8W-35-4
8W - 35 - 2 8W - 35 ANTI-LOCK BRAKESPL

Downloaded from www.Manualslib.com manuals search engine 10FUSE15A
10
30
1
10
ABS
RELAY
BOX
F12
18
DG/WT
1547
CONTROLLER
ANTI-LOCK
BRAKEABS
SYSTEM
RELAY
OUTPUT
G101
Z1
14
BK
Z1
14
BK
S108 BLOCK FUSE
ST-RUN A21
7
9
C22
CLUSTER
INSTRUMENT
G19
22
LG/OR
G19
20
LG/BR
1C103
ABS
SYSTEM
RELAY
CONTROL
G19
20
LG/BR
F12
20
DG/WT
6C101
S109
F12
20
DG/WT
B47
20
RD/LB
60
B57
20
BR/BK
ABS
SYSTEM
RELAY LAMP WARNING
ABSABS
PUMP
MOTOR
RELAY
4
57
CONTROLRELAY SYSTEMABSDRIVERLAMP WARNINGABS(8W-11-9)
(8W-15-2) (8W-15-2) (8W-11-2)
(8W-40-5)
(8W-11-9) (8W-10-12)
8W - 35 - 2 8W-35 ANTI-LOCK BRAKESPL-RHD
978W-1PLR03501

Downloaded from www.Manualslib.com manuals search engine 8W-35 ANTI-LOCK BRAKES
INDEX
page page
DESCRIPTION AND OPERATION
ABS PUMP MOTOR RELAY................ 6
ABS SYSTEM RELAY..................... 6
ABS WARNING LAMP..................... 6
ANTI-LOCK BRAKES..................... 6BRAKE SWITCH INPUT................... 7
DATA LINK CONNECTOR.................. 7
HELPFUL INFORMATION.................. 7
HYDRAULIC MODULATOR................. 6
WHEEL SPEED SENSORS................. 7
DESCRIPTION AND OPERATION
ANTI-LOCK BRAKES
Power for the Anti-Lock brake system is supplied
by two fuses. There is a 15 amp fuse located in the
fuse block cavity 10. This fuse supplies power to the
Controller Anti Lock Brake (CAB), and the ABS sys-
tem relay on the F12 circuit. The F12 circuit also
supplies power to the Powertrain Control Module
(PCM). Power for the fuse is supplied on the A21 cir-
cuit from the ignition switch. This fuse is HOT in the
START/RUN position.
The second fuse is located in the Power Distribu-
tion Center (PDC). It is a 40 amp fuse. This fuse is
HOT at all times and supplies power to the contact
side of the ABS pump motor relay.
There are three grounding points used in the ABS
system. One is a case ground on the CAB. The sec-
ond is the Z12 circuit at the CAB connector cavity 5.
This ground is spliced, and terminates at the left side
of the radiator closure panel.
The third ground is on the Z1 circuit. This ground
is used for the ABS hydraulic modulator, ABS system
relay, and the ABS pump motor. This ground, like the
Z12 ground splices and terminates at the left head-
lamp ground.
Additional information on the circuit function of
the ABS system is listed below. For diagnostic and
testing procedures, refer to the appropriate section of
the Service Manual or the Diagnostic Test Proce-
dures Manual.
ABS WARNING LAMP
The ABS warning lamp is an output from the Con-
troller Anti Lock Brake (CAB) and the ABS relay
box. It is used to alert the operator of a problem in
the ABS system. The G19 circuit from the CAB and
the ABS system relay is used to detect a problem. If
a problem is detected, the CAB grounds the G19 cir-
cuit and illuminates the lamp in the instrument clus-
ter.
Circuit G19 is also an output of the CAB to the
ABS system relay contact side.
ABS SYSTEM RELAY
The system relay is used for the operation of the
ABS system. Power for the relay is supplied on the
B57 circuit from cavity 57 of the Controller Anti Lock
Brake (CAB).
Ground for the relay is on the Z1 circuit. This
ground is spliced in with the pump motor and termi-
nates at the left headlamp ground.
When the system is operating normally power for
the contact side of the relay is supplied from the
CAB on the B57 circuit. It passes through the relay
to the Z1 ground and terminates at the left headlamp
ground. If a problem is detected in the system, the
contact side of the relay switches from the Z1 to the
F12 circuit. This causes the ABS warning lamp in
the instrument cluster to illuminate.
ABS PUMP MOTOR RELAY
The ABS pump motor relay controls when the
pump motor runs. Power for the coil side of the relay
is supplied from cavity 47 of the Controller Anti Lock
Brake (CAB) on the B47 circuit. This circuit also sup-
plies voltage for the contact side of the system relay.
The ground side of the coil is controlled by the B116
circuit. Circuit B116 connects to cavity 16 of the CAB
connector.
Circuit B120 from cavity 20 of the CAB connector
powers the ABS pump motor. This circuit is also used
as an input to the CAB for pump motor monitoring.
HYDRAULIC MODULATOR
The hydraulic modulator is used for the controlling
of the brake system pressure to the wheels. The mod-
ulator is made up of four solenoids.
Circuits involved are, B142 for the left front wheel,
B143 for the right front wheel, B146 for the left rear
wheel, and B148 for the right rear wheel.
The solenoids use a common ground on the Z1 cir-
cuit. There are two Z1 circuits from the modulator.
Both of these grounds terminate at the left headlamp
ground, and are spliced in with the ABS pump motor
and the ABS system relay.
8W - 35 - 6 8W - 35 ANTI-LOCK BRAKESPL

Downloaded from www.Manualslib.com manuals search engine 8W-40 INSTRUMENT CLUSTER
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION.......................................................... 7
Component Page
ABS Relay Box......................8W-40-5
Airbag Control Module................8W-40-5
Airbag Warning Lamp.................8W-40-5
Anti-Lock Warning Lamp..............8W-40-5
Brake Warning Lamp.................8W-40-5
Brake Warning Lamp Switch...........8W-40-5
Charge Indicator Lamp................8W-40-5
Check Engine Lamp..................8W-40-6
Cluster Illumination Lamps............8W-40-2
Controller Anti-Lock Brake.............8W-40-5
Engine Coolant Temperature Gauge......8W-40-6
Engine Coolant Temperature Sensor......8W-40-6
Engine Oil Pressure Switch............8W-40-6
Fuel Gauge.........................8W-40-6
Fuel Pump Module...................8W-40-6
Fuse 9 (FB).........................8W-40-2
Fuse 11 (FB)........................8W-40-6
Fuse 13 (PDC).......................8W-40-3
Fuse Block........................8W-40-2, 6
G101..............................8W-40-5
G204..............................8W-40-6
Headlamp Dimmer And Optical
Horn Switch......................8W-40-2
Headlamp Switch..................8W-40-2, 3
High Beam Indicator Lamp.............8W-40-2
Instrument Cluster...........8W-40-2, 3, 4, 5, 6
Key-In Switch.......................8W-40-3Component Page
Left Front Door Jamb Switch...........8W-40-3
Left Park/Turn Signal Lamp............8W-40-4
Left Repeater Lamp..................8W-40-4
Left Turn Indicator Lamp..............8W-40-4
Low Oil Pressure Lamp...............8W-40-6
Park Brake Switch...................8W-40-5
Power Distribution Center.............8W-40-3
Powertrain Control Module.........8W-40-3, 5, 6
Right Park/Turn Signal Lamp...........8W-40-4
Right Repeater Lamp.................8W-40-4
Right Turn Indicator Lamp.............8W-40-4
S107..............................8W-40-5
S112 ..............................8W-40-4
S116 ..............................8W-40-4
S127..............................8W-40-5
S201..............................8W-40-6
S203..............................8W-40-3
S207..............................8W-40-4
S208..............................8W-40-5
S209..............................8W-40-2
S210..............................8W-40-2
S212..............................8W-40-4
Seat Belt Warning Lamp...............8W-40-5
Turn Signal/Hazard Switch.............8W-40-4
Vehicle Speed Sensor..................8W-40-3
8W - 40 - 2 8W - 40 INSTRUMENT CLUSTERPL

Downloaded from www.Manualslib.com manuals search engine CLUSTER INSTRUMENT
C26C22
G9
22
GY/BK
S208
G9
22
GY/BK
SWITCH BRAKE
PARK
G9
20
GY/BK 2
B A
Z1
20
BK
Z1
18
BK
S107
G101
7
ABS
RELAY
BOXABS
WARNING
LAMPG19
22
LG/OR
G19
20
LG/BR
1
15
CONTROLLER
ANTI-LOCK
BRAKEABS
WARNING
LAMPG19
20
LG/BR
G9
20
GY/BK
SWITCH LAMP
WARNING
BRAKE
BRAKE
WARNING
LAMP LAMPWARNING
ANTI-LOCK
C279C1
C156
GENERATORG12
22
TN/BK
G12
20
TN/BK
6C103
9
R41
18
BK/TN
AIRBAG
CONTROL
MODULEAIRBAG
WARNING
LAMP
POWERTRAIN
CONTROL
MODULE
CHARGE
INDICATOR
LAMP LAMPWARNING
AIRBAGSEAT
BELT
WARNING
LAMP
DRIVERLAMP
C14
G10
20
LG/RD
NO
CONNECTION
S127
Z1
18
BK
(8W-70-3)
(8W-15-2)
(8W-15-2)(8W-35-2)
(8W-35-2)(8W-43-3)
(8W-30-11)
PL-RHD8W-40 INSTRUMENT CLUSTER 8W - 40 - 5
PLR04004978W-1

Downloaded from www.Manualslib.com manuals search engine 8W-40 INSTRUMENT CLUSTER
INDEX
page page
DESCRIPTION AND OPERATION
AIRBAG WARNING LAMP.................. 8
ANTI-LOCK WARNING LAMP............... 9
BRAKE WARNING INDICATOR LAMP......... 8
CHARGE INDICATOR LAMP................ 8
ENGINE COOLANT TEMPERATURE GAUGE . . . 7
FUEL GAUGE........................... 7
HEADLAMP ON CHIME.................... 8
HELPFUL INFORMATION.................. 9
HIGH BEAM INDICATOR LAMP.............. 8
INSTRUMENT CLUSTER.................. 7KEY-IN CHIME.......................... 8
LOW FUEL LAMP........................ 8
LOW OIL PRESSURE LAMP................ 8
ODOMETER............................ 8
RIGHT AND LEFT TURN
SIGNAL INDICATORS................... 8
SEAT BELT WARNING INDICATOR........... 8
SERVICE ENGINE SOON LAMP............. 8
SPEEDOMETER......................... 7
TACHOMETER.......................... 7
DESCRIPTION AND OPERATION
INSTRUMENT CLUSTER
The Instrument Cluster, located on the right side
of the instrument panel, provides the operator with
gauges and warning lamps relating to vehicle opera-
tion. All gauges in the standard and optional cluster
are magnetic type and logic driven.
Battery voltage for the clusters warning lamps and
gauges is provided on the G5 circuit. This circuit con-
nects from the fuse block and is protected bya5amp
fuse located in cavity 11. The cluster is powered only
when the ignition switch is in the START or RUN
position. The cluster is also powered on initial driv-
er's door opening.
Illumination lamps, internal to the cluster, receive
battery voltage on the E2 circuit from the 4 amp fuse
located in cavity 12 of the fuse block. This circuit is
HOT only when the headlamp switch is in the ON
position. Grounding for the cluster is provided on the
Z3 circuit and terminates at the instrument panel
left center support.
The M1 circuit also feeds the cluster through a 10
amp fuse in the Power Distribution Center (PDC).
This fuse is HOT at all times and also used to power
the underhood lamp, and the interior lamps. The
fuse is also lifted OPEN during vehicle shipping to
reduce battery draw.
SPEEDOMETER
The speedometer and odometer receive their infor-
mation on the G7 circuit from the Vehicle Speed Sen-
sor (VSS) on manual and 3±spd automatic
transmission applications. The G7 circuit also pro-
vides a signal to the Powertrain Control Module
(PCM).Logic internal to the instrument cluster adjusts the
position of the gauge pointer to the correct vehicle
speed using the signal on the G7 circuit.
TACHOMETER
The tachometer is connected to the Powertrain
Control Module (PCM) on the G21 circuit. It uses
solid state circuity to decode the ignition pulses
received from the PCM to adjust the gauge pointer to
the proper position.
ENGINE COOLANT TEMPERATURE GAUGE
The temperature gauge is connected to the engine
coolant temperature sensor on the G20 circuit. The
engine coolant temperature sensor for the gauge is a
combination unit. One side of the unit is used for the
Powertrain Control Module (PCM) and the other side
for the cluster. The sending unit is case grounded to
the engine.
The logic driven gauge moves in response to the
measured resistance of the engine coolant tempera-
ture sending unit.
FUEL GAUGE
The fuel level gauge is connected to the fuel pump
module on the G4 circuit. The fuel pump module con-
tains the fuel pump and a variable resistor for the
gauge. Grounding for the fuel pump module is pro-
vided on the Z2 circuit and terminates at the left
rear wheel house.
The logic driven gauge moves in response to the
measured resistance of the fuel tank sending unit.
The fuel level sensor contains a variable resistor.
As the position of the float arm on the level sensor
changes, the resistor changes the current flow
through the fuel gauge circuit. A change in current
flow alters the magnetic field in the fuel gauge which
changes the pointer position.
PL8W - 40 INSTRUMENT CLUSTER 8W - 40 - 7

Downloaded from www.Manualslib.com manuals search engine ODOMETER
The speedometer and odometer receive their infor-
mation on the G7 circuit from the Vehicle Speed Sen-
sor (VSS) on vehicles equipped with the manual or
3±spd automatic transmission. This circuit also pro-
vides a signal to the Powertrain Control Module
(PCM).
Logic internal to the cluster steps the odometer at
a high rate to indicate the proper mileage.
SERVICE ENGINE SOON LAMP
The Service Engine Soon lamp illuminates when
the ignition switch is in the ON position and prior to
starting the vehicle. The lamp will turn off after the
vehicle is started.
If while the vehicle is running a problem is
detected in the engine control system the lamp is
illuminated. This is accomplished by the Powertrain
Control Module (PCM) grounding the G3 circuit.
SEAT BELT WARNING INDICATOR
The fasten seat belt indicator is used with the
warning chime to indicate to the operator to fasten
the seat belt. There is a switch located in the drivers
side B-pillar that is normally OPEN with the seat
belt buckled.
If the seat belt is not buckled the switch CLOSES
and a ground path is completed from the G10 circuit
to the Z1 circuit. This will illuminate the lamp in the
instrument cluster.
When the ignition switch is moved to the START
position the lamp will illuminate. Logic internal to
the instrument cluster determines the length of time.
LOW FUEL LAMP
The low fuel lamp is used to indicate to the opera-
tor that the fuel level is below a predetermined level.
This lamp is logic driven by the instrument cluster.
When the instrument cluster determines a low fuel
condition based on an input from the fuel tank gauge
level sending unit (circuit G4) it illuminates the
lamp.
HEADLAMP ON CHIME
The headlamp ON chime is used to indicate to the
operator that the headlamps or parking lamps are
ON when the drivers door is OPEN. If the lamps are
ON and the drivers door is opened, a ground path is
completed from the G26 circuit at the cluster,
through the headlamp switch, to the G16 circuit and
ending at the door ajar switch. The door ajar switch
is case grounded.
KEY-IN CHIME
The key-in chime is used to indicate to the opera-
tor that the key is in the ignition with the driversdoor OPEN. If the key is in the ignition and the driv-
ers door is OPEN, a ground path is completed from
the G26 circuit at the cluster, through the CLOSED
key-in switch, to the G16 circuit and terminating at
the door ajar switch which is case grounded.
CHARGE INDICATOR LAMP
The Charge Indicator lamp is used to alert the
operator that the charging system voltage has fallen
below the normal operating range. This circuit is con-
trolled by the Powertrain Control Module (PCM).
When the PCM determines a problem, it grounds the
G12 circuit.
AIRBAG WARNING LAMP
The Airbag Warning lamp is used to alert the oper-
ator of a problem with the Airbag system. The lamp
is illuminated when the Airbag Control Module
(ACM) grounds the R41 circuit. Refer to the appro-
priate section of the Service Manual or Diagnostic
Test Procedures Manual to diagnosis this system.
LOW OIL PRESSURE LAMP
The low oil pressure lamp is used to indicate to the
operator that the engine oil pressure has dropped
below a predetermined pressure. Power for the lamp
is provided on the G5 circuit which also powers the
other warning lamps.
When the oil pressure is low the normally OPEN
oil pressure switch CLOSES completing a path to
ground on circuit G6. The oil pressure switch is case
grounded to the engine block.
HIGH BEAM INDICATOR LAMP
The High Beam Indicator Lamp is used to indicate
to the operator that the high beam headlamps are
ON. Power is supplied to the cluster on the L3 cir-
cuit. Ground is provided on the Z3 circuit.
Circuit L3 connects from the headlamp dimmer
switch to the instrument cluster.
RIGHT AND LEFT TURN SIGNAL INDICATORS
These lamps are used to indicate to the operator
which turn signal is ON. Power for the lamps comes
from the turn signal switch. The L60 circuit is for the
right turn indicator, and the L61 circuit is used for
the left turn signal indicator. Ground for the circuits
is provided on the Z3 circuit.
BRAKE WARNING INDICATOR LAMP
The Brake Warning Indicator lamp is used to alert
the operator of a problem with the vehicles braking
system. The lamp illuminates when the ignition
switch is turned to START position to perform a self
check.
8W - 40 - 8 8W - 40 INSTRUMENT CLUSTERPL
DESCRIPTION AND OPERATION (Continued)