1997 CADILLAC ELDORADO garage door opener

Downloaded from www.Manualslib.com manuals search engine 1. From inside the vehcie, roll down the window, then
b Get out of the vehicle, keeping the door open.
2. From outside of the vehicle, with the door open, lock
the vehicle using the power
door lock or the RKE
system and close the door. Wait 30 seconds until the
SECURITY lamp goes off.
3. Reach in and unlock the door using the manual lock
and open the door. The horn will sound and the
headlamps will flash.
If the alarm does not sound when it should, check to
see
if the horn works. The horn fuse may be blown. TO
replace the fuse, see “Fuses and Circuit Breakers” in the
Index.
If the fuse does not need to be replaced, YOU may
need to have your Cadillac serviced.
To reduce the possibility of theft, always activate the
optional theft-deterrent system when leaving your vehicle. Pressing
the VALET button
located inside the glove
box
will disable the use of. the
trunk, fuel door and garage’
~ door opener. Pressing this
button again will make
these features reusable.
’ ’ Locking the glove box witk
the door key
will also help
to secure your vehicle.
Note
that the RKE transmitter can’t be used to open th
trunk or fuel door if the VALET button is pressed in.
2

Downloaded from www.Manualslib.com manuals search engine The reading lamps are located in the roof. These lamps
and the interior courtesy lamps come on when either
door is opened and it is dark outside. Press
the button to
turn them
on. Press it again to turn them off.
If the reading lamps are left on, they automatically shut
off 10 minutes after the ignition has been turned off.
This feature is designed to protect your vehicle’s battery
against drainage from the interior lamps, trunk lamp, glove
box lamp, cigarette lighters or
the garage door
opener. When the ignition is turned
off, the power
to these features will automatically
turn off after
10 minutes (three minutes if a new car has 15 miles
or less). Power will be restored for
an additional
10 minutes if either door is opened, the trunk is opened
or the courtesy lamp switch is turned on.
This feature is for long term use and must be
programmed through the
DIC while the ignition is in the
RUN position. Battery guard storage protects the battery
by placing the vehicle
in a storage mode so that the
radio, amplifiers, instrument cluster and
RKE will not
drain
the battery over a long period of time.
To begin programming, press the INFORMATION
(INFO) and RESET (INFO RESET) buttons at the same
time
for about two seconds. The first message to appear
is DOORS LOCK IN GEAR. Press the INFORMATION
(INFO) button after this prompt is displayed until
STORAGE MODE prompt appears on the DIC. Press
the
TRIP SET (TRIP RESET’) button to answer “yes”
or press the RESET (INFO RESET) button to indicate a
“no” response.

Downloaded from www.Manualslib.com manuals search engine Do not use the universal transmitter with any garage
door opener that does not have the “stop and reverse”
safety feature.
This includes any garage door opener
model manufactured before April
1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
Your vehicle’s engine should be turned
off while
programming the transmitter. Follow these steps to
program up to three channels:
1. If you have previously programmed a transmitter
channel, proceed
to Step 2. Otherwise, hold down the
two outside buttons on the universal transmitter until
the red light begins to flash rapidly (approximately
20 seconds). Then release the buttons. This procedure
initializes
the memory and erases any previous
settings for all three channels.
2. Decide which one of the three channels you want
to program.
3.
4.
5.
Hold the end of the hand-held transmitter against the
front surface of
the universal transmitter so that you
can still see the red Light.
Using both hands, press the hand-held transmitter
button and
the desired button on the universal
transmitter. Continue to press both buttons through
Step
5.
Hold down both buttons until you see the red light
on the universal transmitter flash slowly and then
rapidly. The rapid flashing, which could take up to
90 seconds, indicates that the universal transmitter
has been programmed. Release both buttons once
the light starts to
flash rapidly.
If you have trouble programming the universal
transmitter, make sure that you have followed the
directions exactly
as described and that the battery in the
hand-held transmitter is not dead. If you still cannot
program it, rotate the hand-held transmitter end over end
and try again. The universal transmitter may not work
with older garage door openers that
do not meet current
Federal Consumer Safety Standards. If
you cannot
program the transmitter after repeated attempts, consult
YOU Cadillac dealer.
2-

Downloaded from www.Manualslib.com manuals search engine Be sure to keep the original hand-held transmitter
in case you need to erase and reprogram the
universal transmitter.
Note to Canadian Owners: During programming, the
hand-held transmitter may stop transmitting after one or
two seconds. If you are programming from one of these
transmitters, you should press and re-press
the button
on the hand-held transmitter every two seconds without
ever releasing
the button on the universal transmitter.
Release both buttons when the red light
on the universal
transmitter begins to flash rapidly.
Press and hold the appropriate button on the universal
transmitter. The red light
comes on while the signal is
being transmitted. Note that
the universal transmitter is disabled when the
VALET button
inside the glove box is activated. For
more information, see “Security Override” earlier in
this section.
Also note that if the hand-held transmitter appears to
program
the universal transmitter but does not open
your garage door,
and if the garage door opener was
manufactured after 1995, the garage door opener may
have
a “rolling code” system. A rolling code system
changes the code
of the garage door opener every time
you open or close the garage door.
To determine if you have this system, press the button
on the universal transmitter that you have programmed
already.
If the red light on the universal transmitter
flashes rapidly for
one or two seconds and then
stops flashing, the garage door opener has a rolling
code system.

Downloaded from www.Manualslib.com manuals search engine If you have not previously programmed the
hand-held transmitter to the universal transmitter, see
“Programming the Transmitter” earlier in this section.
If
you have completed this programming already, you now
need to train the garage door opener receiver to
recognize the universal transmitter.
1. Remove the cover panel from the garage door opener
receiver (the receiver should be located by the
garage door opener motor).
receiver.
The exact location and color of the button
may
vary by garage door opener brand. If you have
difficulty locating the training button,
refer to your
garage door opener manual.
2. Locate the training button on the garage door opener
3. Press the training button on the garage door opener
receiver for one or two seconds.
4. Return to the universal transmitter in your vehicle
and press the universal transmitter button
you have
already programmed for two
to three seconds. Press
the button again to make sure that the universal
transmitter has been trained
to the garage door
opener receiver.
The garage door opener should now recognize the
universal transmitter.
You may either use the universal
transmitter or the hand-held transmitter to open the
garage door.
If after following these instructions you still have
problems training the
garage door opener, consult your
Cadillac dealer.
To erase all three programmed channels, hold down the
two outside
buttons until the red light begins to flash.
Individual channels cannot
be erased, but can be
reprogrammed using the procedure for programming the
transmitter explained earlier.

Downloaded from www.Manualslib.com manuals search engine (irilIunn]
COR LPS INT LPS CIG LTR1 CIG LTRP
Innnnnl
L HDLP LO R HDLP LO L HDLP HI R HDLP HI
I , HDLPS I I HAZARD I I STOP I I MIRROR I I DRL , I
I , IGN O(ENG) , I , I ABS I I IGN 1 I I WIPERS , I
FUSE CENTER IDENTIFICATION
000
A/C COMP PCM(BAT) PRK/REV
A/C COMP
I I Daytime Running Lamps I
I CQRLPS
Cornering Lamp Switch, Right
and Left Cornering
Lamps I
Fuse
INT LPS
CIG LTR1
CIG La2
L HDLP LO
W HDLP LO
L HDLP HI
R HDLP HI
FOG
mLPs
Usage
Trunk Lamp, Courtesy Lamps,
Front Vanity Lamps, Glove Box
Lamp, Garage Door Opener,
Courtesy
Lamp Relay
Front and Rear Cigarette Lighters
(Full Console Only)
Right and Left Rear Cigarette
Lighters
Left Low-Beam Meadlamp
Right Low-Beam Weadlamp
Left High-Beam Headlamp
Right High-Beam Headlamp
Right and Left Front
Fog Lamp
Relay
Meadlamp Relay, High/Low Beam
Control Relay, Right and Left
Low/High Beam
Fuses