1997 AUDI A4 light

46-48


Note:
Do not damage control module -1- for immobilizer (where applicable)
when removing pedal assembly. - Remove brake light switch -3- and CCS vent valves -2-.
- Remove hex socket-head bolt (arrow) for attaching pedal assembly to
instrument panel member.
- Pull pedal assembly down and remove.

- To remove accelerator pedal, press catch in direction shown (arrows)
while pressing out accelerator pedal.
Pa
ge 3 of 10 Brake
pedal, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.7

46-49

Installing

CAUTION!

Do not remove safety wire or other
removal/installation aids from steering
column until after the universal joint has been
re-installed on the steering gear pinion.

- Install pedal assembly onto joint pin.

Note:
Do not tighten hex socket-head bolt (arrow) for attaching pedal assembly
to instrument panel member until after installing the brake servo unit.
After installing: - Install hex socket-head bolt (arrow) for attaching pedal assembly to
instrument panel member and tighten by hand.
- Attach accelerator pedal (AP) cable.
- Install brake servo unit page 47
-37
.
- Bleed brakes page 47
-23
.
- Bleed clutch Repair Manual, Manual Transmission 012 Front
Wheel Drive or Manual Transmission 01A All Wheel Drive, Repair
Group 30. -
Adjust brake light switch ( page 46
-50
) and CCS vent valves (
Pa
ge 4 of 10 Brake
pedal, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.7

46-50

Brake light switch -F-, adjusting


The pedal assembly must be bolted tight to
the brake servo and to the instrument panel
member before carrying out the adjustment.
The following adjustments should be carried out
in case of complaint:

Pedal bracket for brake light switch with retaining clip
CAUTION!
Part numbers are listed here for reference only. Always check with
your Parts department for the latest information. 1 - Brake light switch
2 - Hex nut, M12 x 1.5
Part No. N 011 162 9
3 - Spring washer, M12
Part No. N 012 232 3
4 - Hex nut, M12 x 1.5
Part No. N 011 162 9
5 - Brake pedal
Pa
ge 6 of 10 Brake
pedal, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.7

46-51


- Pull brake light switch out of pedal bracket.
- Remove clip page 46
-45
, item - 20 -.
- Turn nut -2- on brake light switch.
- Install brake light switch in pedal bracket, insert spring washer -3- and
nut -4-.
- Adjust clearance -A-, then tighten nut -4-.

Dimension -A- = 0.1 to 0.5 mm (0.004 to 0.020 in.)
Tightening torque: 4 Nm (35 in lb)
Pa
ge 7 of 10 Brake
pedal, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.7

46-52


Pedal bracket with internal thread for brake light switch
Note:
Between the nut and the pedal bracket there is a spring clip (not shown),
Part No. N 012 042 4.
CAUTION!
Part numbers are listed here for reference only. Always check with
your Parts department for the latest information. 1 - Brake light switch
2 - Hex nut, M12 x 1.5
Part No. N 011 020 8
3 - Brake pedal
- Install brake light switch in pedal bracket.
- Adjust clearance -A-, then tighten nut -2-.

Dimension -A- = 0.1 to 0.5 mm (0.004 to 0.020 in.)
Tightening torque: 4.5 Nm (39 in lb)
Pa
ge 8 of 10 Brake
pedal, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.7

46-53


With spring clip for the brake light switch
Note:
The switch must be installed only once in order to assure that it is
adequately tight.
Adjusting switch
Note: 1 - Stop surface of brake pedal
2 - Spring clip
Press into pedal cluster from behind
3 - Pedal cluster
4 - Brake light switch -F-
a - Clearance: max. 0.7 mm (0.028 in.)
- Insert switch -4- into installed clip -2- and press in to stop.
As a result of this step, the brake pedal must not be under preload.If necessary, turn switch back somewhat, noting clearance -a-.
Pa
ge 9 of 10 Brake
pedal, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.7

46-54

Cruise Control System (CCS) vent valve,
adjusting


- Insert vent valve into clip and push through to
stop.

- Push back valve by pulling back brake pedal or
clutch pedal to stop.

Note:
Only install the valve one time, otherwise an
adequately tight fit cannot be assured.

Version with spring clip for the vent valve

- Same procedure as for the brake light switch
page 46-53
.
Pa
ge 10 of 10 Brake
pedal, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.7