1997 AUDI A4 engine

01-78

Readiness code is returned to "0 1 1 0 1 1 0
1" if:

DTC memory was erased,
Voltage supply to ECM was cut off (e.g.
connector disconnected, battery disconnected)
a new Engine Control Module (ECM) was
installed
In this case, readiness code must be re-
generated Page 01
-84
.

Note:
During driving operation in various load
conditions, exhaust relevant tests are performed
by the control module and the readiness code is
generated on its own. In this case, however, the
concluding control possibilities are not available,
meaning that it will not be indicated whether the
vehicle is free of malfunctions upon transfer to
the customer.
Pa
ge 2 of 43 Readiness code
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-79

Readiness code, checking


Test sequence

- Connect VAS5051 tester Page 01
-7 and
select vehicle system "01 - Engine electronics".
Engine must run at idle for this.

Display on VAS5051:
- Select diagnostic function "08 - read measured value block" in
selection -1-.

Display on VAS5051:
1 - Enter display group Max. input value = 255
- Select function "086" in button field -2- for "Display group number 086"
and press Q button to confirm input.
Pa
ge 3 of 43 Readiness code
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-84

Readiness code, generating


Special Tools and Equipment

Requirements
Important note:
If, during a work step, the test result is indicated as "OK" immediately after
selecting a display group, the test has already been carried out and it is
OK to continue on to the next work step.
VAG1788/10 RPM adjusterVehicle stationary Vehicles with automatic transmission Selector lever in P or N. Electrical consumers switched off (radiator fan must NOT run during
test). A/C switched off. Coolant temperature at least 80 C Display group 004, display
field 3. Important: Drive engine warm via road test if possible.
Pa
ge 9 of 43 Readiness code
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-85

Work step 1: Check DTC Memory

Test requirement:

Engine not running, ignition switched on.

- Connect VAS5051 tester Page 01
-7 and
select vehicle system "01 - Engine electronics".
Ignition must remain switched on for this.

Display on VAS5051:
- In selection -1-, click on the diagnostic function "02 - Check DTC
memory".

Display on VAS5051:
1 - DTC memory content:

0 malfunctions recognized
or

X malfunctions recognized
Pa
ge 10 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-87

Work step 2: Erase DTC Memory

Test requirement:

Engine not running, ignition switched on.

Display on VAS5051:
Note:
When DTC memory is erased, readiness code is reset and must therefore
be re-generated. - In selection -1-, click on the diagnostic function "05 - Check DTC
memory".

Display on VAS5051:
1 - no indication (before erasing)
or

DTC memory erased
2 - Note:Perform the function?Note: Data is being erased !
- Press on "OK" button in display -2-.
-
Click on - button
Pa
ge 13 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-88

Work step 3: Adapt throttle valve control
module to Engine Control Module (ECM)

Test requirement:

Engine not running, ignition switched on.

Display on VAS5051:
- In selection -1-, click on the diagnostic function "04 - Basic setting".

Display on VAS5051:
1 - Enter display group Max. input value = 255
- Select function "060" in button field -2- for "display group number 060"
and press Q button to confirm input.
Pa
ge 14 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-91

Work step 4: Kick down function, adapting
1)

1) Only vehicles with automatic transmission

Test requirement:

Engine not running, ignition switched on.

Display on VAS5051:
Note:
There will be a prompt: "Operate kick down".
Note:
During adaptation of the kick down point, "Kick down ADP in progress" will
be indicated in display. After successful adaptation of the kick down point,
"Kick down ADP OK" will be indicated on display. -
Press button 3 times to change into display group 063.- Depress accelerator pedal completely, past kick down point, and hold
down.
- Check specified value in display field -4-.
Pa
ge 18 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-93

Work step 5: Check operating condition of
oxygen sensor control

- Start engine (for a vehicle with manual
transmission: engage clutch).

Note:
If necessary, vehicle system "01 - engine
electronics" and diagnostic function "04 -basic
setting" must be selected again after engine
start.

- Install VAG1788/10 RPM adjuster on the
accelerator pedal and raise the engine speed to
2600 RPM.

Test requirement:

Engine running at 2600 RPM.

Display on VAS5051:
-
Click on - button
Pa
ge 21 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7