1997 AUDI A4 AHA Engine On Board Diagnostic Workshop Manual

01-48

Diagnostic Trouble
Code (DTC)
Malfunction text
MIL
Corrective action
SAE
VAG



P1624 18032 MIL Request Sign. active Immed.
Repair Manual, 5 Spd. Automatic Transmission 01V,
Repair Group 01 - Check DTC memory for Transmission Control Module
(TCM) and correct malfunctions
P1626 18034 CAN-Bus
Missing Message from
Transm. Contr. 2 Dcy
- Check CAN-Bus page 24
-172
P1640 18048 Internal Contr. Module
(EEPROM)
Error 2 Dcy
- Replace ECM page 01
-68
P1681 18089 Contr. Unit Programming
Programming not Finished Immed.
- Replace ECM page 01
-68
P1690 18098 Malfunction Indicator Light
Malfunction Off
- Check wire from ECM to Malfunction Indicator Light
(MIL) page 01
-2
Note for DTC P1624/18032:
If this malfunction is detected by the Transmission Control Module (TCM), the MIL is switched on by the ECM. In this case,
the ECM stores the malfunction "MIL Request Sign. active" (DTC P1624/18032). After repairing the malfunction, erase DTC
memory of the ECM.
Pa
ge 65 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-49

Erase DTC Memory (scan tool function
05)


Required special tools and test equipment
VAG1551 Scan Tool (ST) with VAG1551/3
adapter cable

Test condition
Malfunction(s) repaired

Note:
If DTC memory has been erased, generate new
readiness code page 01
-73
.

Erasing

- Connect VAG1551/VAG1552 Scan Tool (ST)
and press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (engine running at
idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -2- to select "Check DTC Memory" function 02,
and press -Q- button to confirm input.
-
Press button to advance through program sequence until all stored
malfunctions have been displayed.
Pa
ge 66 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

Rapid data transfer
HELP
Select function XX

Indicated on display
Pa
ge 67 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-50

- Press buttons -0- and -5- to select "Erase DTC
Memory" function 05, and press -Q- button to
confirm input. Rapid data transfer DTC Memory is erased

Indicated on display
-
Press button to advance through program sequence.
Rapid data transfer
HELP
Select function XX

Indicated on display
Safety precautions for road testing vehicle page 24
-9 - Press buttons -0- and -6- to select "End Output" function 06, and press
-Q- button to confirm input.
- Road test.
- Initiate "Automatic Test Sequence" by pressing -0- button twice to
insert address word 00.
- Check readiness code page 01
-70
. If DTC memory has been
erased, or ECM has been disconnected, generate readiness code
page 01
-73
.
Pa
ge 68 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-51

Output Diagnostic Test Mode (DTM)
(scan tool function 03)


Notes:

The output Diagnostic Test Mode (DTM) can be
activated only with ignition switched on and the
engine not running.
The output DTM is interrupted if the engine is
started, or if a rotary pulse from the ignition
system is recognized.
When operating in the output DTM, the
individual output signals are actuated until the
program sequence is advanced by pressing the
button.

Output signals are checked by listening for the
sound of the component being actuated, or
feeling for mechanical evidence of actuation,
such as clicking, vibration, etc.
Without letting the engine run, briefly switch the
ignition off for approx. 20 seconds before
repeating the output checks.
During the entire output DTM sequence, the
electric fuel pump will run.
Pa
ge 69 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

The output DTM will be interrupted after 10
minutes.
Component locations page 24
-1
Pa
ge 70 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-52
The following components are actuated in
sequence:

1. Cylinder 1 fuel injector -N30-
2. Cylinder 2 fuel injector -N31-
3. Cylinder 3 fuel injector -N32-
4. Cylinder 4 fuel injector -N33-
5. Cylinder 5 fuel injector -N83-
6. Cylinder 6 fuel injector -N84-
7. EVAP canister purge regulator valve -N80-
8. Secondary AIR solenoid valve -N112-
9. Secondary AIR pump relay -J299-
10.
Intake manifold tuning valve -N156-
(change-over valve)
11.
Camshaft adjustment 1 (Valves -1- and -2-
for camshaft adjustment, -N205- and -N208-
)

Required special tools and testing
equipment

VAG1551 Scan Tool (ST) with VAG1551/3
adapter cable

Test conditions
Pa
ge 71 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

Fuse for Engine Control Module (ECM) OK
Closed Throttle Position (CTP) switch -F60-
OK
Fuel pump relay OK
Pa
ge 72 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1