1996 VOLVO 850 wheel torque

1996 Volvo 850
WARNING!
l The jack attachment must engage the bar in the jack attachment (A). Th\
e car's weight must not rest
on the jack's attachment (B).
l Be sure the jack is on a firm, level, non-slippery surface.
l Never allow any part of your body to be extended under a car supported b\
y a jack.
l Use the jack intended for the car when replacing a wheel. For any other \
job, use stands to support
the end of the car being worked on.
l Apply the parking brake, select position P (automatic transmission) or\
Reverse gear (manual
transmission).
l Block the wheels standing on the ground. Use rigid wooden blocks or larg\
e stones.
l The jack should be kept well-greased.

Installing the wheel

Clean the contact surfaces on the wheel and hub. Lift the wheel and plac\
e it on the hub. Make sure that
you align the wheel with the guide stud on the wheel hub prior to instal\
lation. Install the wheel bolts
cross-wise (see illustration) and tighten by turning lightly clockwise\
. Lower the vehicle to the ground
and alternately tighten the bolts to 81 ft. lbs. (110 NM). Install the\
wheel cap (where applicable).
CAUTION: Correct tightening torque on wheel bolts must be observed. The \
wheel bolts should never
be greased or lubricated. The extended, chromed wheel bolts must not be \
used with steel rims, as they
make is impossible to fit the hub caps.


Correct tightening order for wheel bolts
pg. 6:4 Spare tire
file:///K|/ownersdocs/1996/1996_850/96850_601.htm (4 of 5)12/30/2006 9\
:59:39 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
support frame and under the reinforced plate in the spare wheel well. Ta\
ke care not to damage the splash
guard under the engine. Ensure that the jack is positioned so that the c\
ar cannot slide off it. Always use
axle stands or similar structures.


If a two-post hoist is used to lift the car, the front and rear lift arm\
pads should be centered under the
reinforced lift plates on the inboard edge of the sill rail. The positio\
n of these plates is marked with
arrows molded into the bottom of the sill rail.
CAUTION: 850 R turbo models have reduced ground clearance due to the des\
ign of the front spoiler.
Please observe caution when driving the car onto a garage hoist.
pg. 8:7 Servicing (cont.)
Torque exhaust and intake manifold nuts

A loose manifold could alter air/fuel ratio and cause an increase in emi\
ssion and/or poor driveability.

Air cleaner

Replace the air cleaner cartridge with a new one every 30,000 miles (48\
,000 km). The cartridge should
be replaced more often when driving under dirty and dusty conditions. Th\
e filter cannot be cleaned and
therefore should always be replaced with a new one.

Vacuum fittings, hoses and connections
file:///K|/ownersdocs/1996/1996_850/96850_806.htm (2 of 11)12/30/2006 \
9:59:52 AMClassic Cars & Cycles www.ClassicCycles.org

1996 Volvo 850
Turbo: Champion RC7GYC (or equivalent)
Spark plug gap 0.028" (0.7 mm)
Tightening torque 18.4 ft. lbs. +/- 3.7 ft. lbs. (25 Nm +/- 5 Nm)

Front suspension

Spring strut suspension with integrated shock absorbers and control arm \
linked to the support frame.
Power-assisted rack and pinion steering. Safety type steering column.
The alignment specifications apply to an unladen car but include fuel, c\
oolant, and spare wheel.

Toe-in measured on the wheel rims: 2.4 mm +/- 0.7 mm
Toe-in measured on tire sides: 2.9 +/- 0.9 mm

Rear Suspension

Delta-link individual rear-wheel suspension with longitudinal support ar\
ms, double link arms and track
rods.

Toe-in measured on the tire sides: 4° +/- 10°

All specifications are subject to change without notice. pg. 9:5 Specifications (cont.)
Power transmission

Manual transmission: M 56 H
Single-disc dry plate clutch. All-synchromesh on all gears including rev\
erse; integrated final drive.
Operation via a floor mounted gear lever.

Final drive ratio 4.00:1
Reduction ratios
file:///K|/ownersdocs/1996/1996_850/96850_901.htm (5 of 7)12/30/2006 9\
:59:55 AMClassic Cars & Cycles www.ClassicCycles.org