1996 VOLKSWAGEN PASSAT display

Downloaded from www.Manualslib.com manuals search engine 40-81
Note:
A seal is formed directly between the triple-rotor joint
and the drive flange by the rectanular sealing ring.
The cover is no longer required. - Install rectangular sealing ring (arrow) from repair
kit. 90 grams into joint and 90 grams behind joint - Press 180 grams of axle shaft grease from repair
kit into triple-rotor joint .
- Install triple-rotor joint boot. - Install boot clamp. Page 81 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 40-82
- Tighten small diameter clamp with VAG 1275
pliers or equivalent (e.g. KD 474).
CAUTION! Secure the triple-rotor joint with tape so that
the housing is not inadvertently pushed back
when installing the axle shaft. Remove tape just prior to bolting to drive
flange. Page 82 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 42-1

Rear Wheel
Suspension, Shafts
and Axle
Rear axle, servicing
(vehicles with front wheel
drive)
Note: The rear axle and wheel
bearings are identical on
Base and Plus suspension
versions. Welding and straightening
of the axle beam is not
permissible.
1 - Wheel bolt 110 Nm (81
ft lb)
2 - Self-locking hex nut, 70 Nm (52 ft lb) When tightening the
nut the axle beam
must be in the
horizontal position
(unladened vehicle
state)
3 - Hex bolt, 25 Nm (18 ft
lb)
4 - Suspension strut Removing and
installing Fig. 1 to Fig. 3 Disassembling and
assembling Page 42-9 Page 1 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1

Downloaded from www.Manualslib.com manuals search engine 42-2

5 - Wheel bearing Servicing Vehicles with drum brakes Page 42-15 Vehicles with disc
brakes Page 42-24 6 - 80 Nm (59 ft lb) Use only self-locking
nuts with captive
washers When tightening nut, the axle beam must be in the horizontal
position (unladened
vehicle state)
7 - Hex bolt Installed from center of vehicle
8 - Shouldered bolt, 70 Nm (52 ft lb) If threads are
damaged, rework
captive nut in side
member Page 42-7 Page 2 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1

Downloaded from www.Manualslib.com manuals search engine 42-3

9 - Mounting bracket with
retainer for brake
pressure regulator Installation position
Fig. 4 Check and if
necessary adjust rear
axle total toe after
installation If possible do not
loosen when removing
the rear axle
10 - Hex nut/washer, 35 Nm
(26 ft lb)
11 - Regulator spring
bracket
12 - Bonded rubber
mounting Note installation
position Fig. 7 Pressing out Fig. 5
and Fig. 6 Pressing in Fig. 8 Only replace as pair 13 - Axle beam Stub axle contact
surfaces and threaded
holes are to be free of
paint and dirt
14 - Parking brake cable
bracket Page 3 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1

Downloaded from www.Manualslib.com manuals search engine 42-4
Repair Manual, Body Exterior, Interior, Repair Group 70.
Repair Manual, Body Exterior, Interior, Repair Group 68.
Inertia reel bolt (arrow) tightening torque: 40 Nm (30 ft
lb) Fig. 1 Suspension strut at body, removing and installing
- Removing and installing inertia reel cover - Removing and installing inertia reel Remove and install both securing bolts (arrows) from
interior of vehicle (viewed through rear left side
window).
Tightening torque: 25 Nm (18 ft lb) Fig. 2 Suspension strut at body, removing and installing Page 4 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1

Downloaded from www.Manualslib.com manuals search engine 42-5
Suspension strut is attached to the body by 4
retaining lugs in addition to the bolts. To remove, turn
suspension strut until retaining lugs are positioned
above the cut-outs. Fig. 3 Suspension strut, removing and
installing Angle of inclination to axle beam 13 30' 1. Fig. 4 Bolting mounting bracket to axle beam Page 5 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1

Downloaded from www.Manualslib.com manuals search engine 42-6
Note:
Before using special tool 3111 it is important to
grease spindle with Molybdenum grease. Fig. 5 Bonded rubber mounting, pressing 1st
half out of axle beam Thread base plate into the pressure plate 3111/5 from
the opposite side.
Note:
Mounting must not be driven out. Otherwise the
mounting seat will be widened and a tight seating of
the new mounting cannot be assured. Fig. 6 Bonded rubber mounting, pressing 2nd
half out of axle beam Page 6 of 14Rear Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.1