1996 TOYOTA T100 oil filter

Downloaded from www.Manualslib.com manuals search engine LU0817
Recommended Viscosity (SAE):
10W−30
5W−30 PREFERRED
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
LU033−04
P20966SST
P20969
Oil Pressure Gauge
− LUBRICATION (5VZ−FE)OIL AND FILTER
LU−1
1121 Author: Date:
1996 TOYOTA T100 (RM449U)
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If oil quality is visibly poor, replace it.
Oil grade:
API grade SH Energy−Conserving II or ILSAC multi-
grade engine oil.
SAE 5W−30 is the bset choise for your vehicle, for
good fuel economy, and good starting in cold
weather.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the dip-
stick.
3. CHECK OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the lev-
el gauge. If low, check for leakage and add oil up to the ”F” mark.
If low, check for leakage and add oil up to the ”F” mark.
When inserting the oil dipstick, insert the curved tip of the
dipstick facing the same direction as the curve of the
guide.If the dipstick gets caught while inserting it, do not
force it in. Reconfirm the direction of the dipstick.
4. REMOVE OIL PRESSURE SWITCH
Using SST, remove the oil pressure switch.
SST 09816−30010
5. INSTALL OIL PRESSURE GAUGE
6. START ENGINE
Start the engine and warm it up to normal operating tempera-
ture.
7. CHECK OIL PRESSURE
Oil pressure:
At idle speed
29 kPa (0.3 kgf/cm
2, 4.3 psi) or more
At 3,000 rpm
245 − 520 kPa (2.5 − 5.3 kgf/cm
2, 36 − 75 psi)
8. REMOVE OIL PRESSURE GAUGE

Downloaded from www.Manualslib.com manuals search engine P00496
Adhesive
LU−2
− LUBRICATION (5VZ−FE)OIL AND FILTER
1122 Author: Date:
1996 TOYOTA T100 (RM449U)
9. INSTALL OIL PRESSURE SWITCH
(a) Apply adhesive to 2 or 3 threads.
Adhesive:
Part No. 08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(b) Using SST, install the oil pressure switch.
SST 09816−30010
Torque:15 N·m (150 kgf·cm, 11 ft·lbf)
10. START ENGINE AND CHECK FOR LEAKS

Downloaded from www.Manualslib.com manuals search engine LU034−03
P20927
Z04118
LU0490
SST
− LUBRICATION (5VZ−FE)OIL AND FILTER
LU−3
1996 TOYOTA T100 (RM449U)
REPLACEMENT
CAUTION:
Prolonged and repeated contact with mineral oil will result
in the removal of natural fats from the skin, leading to dry-
ness, irritation and dermatitis.In addition, used engine oil
contains potentially harmful contaminants which may
cause skin cancer.
Adequate means of skin protection and washing facilities
should be provided.Care should be taken, therefore, when
changing engine oil, to minimize the frequency and length
of time your skin is exposed to used engine oil.
Protective clothing and gloves, that cannot be penetrated
by oil, should be worn. The skin should be thoroughly
washed with soap and water, or use water−less hand clean-
er, to remove any used engine oil. Do not use gasoline, thin-
ners, or solvents.In order to preserve the environment,
used oil and used oil filters must be disposed of only at
designated disposal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil dipstick.
(c) Remove the oil drain plug and gasket, and drain the oil
into a container.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter (located on left side of the
cylinder block).
SST 09228−07501
(b) Clean the filter contact surface on the filter mounting.
(c) Apply clean engine oil to the gasket of a new oil filter.
(d) Lightly screw the oil filter into place, and tighten it until the
gasket contacts the seat.
(e) Using SST, tighten it an additional 3/4 turn.
SST 09228−07501

Downloaded from www.Manualslib.com manuals search engine LU−4
− LUBRICATION (5VZ−FE)OIL AND FILTER
1996 TOYOTA T100 (RM449U)
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
(b) Fill the engine with new oil.
Oil capacity
ItemCapacity
liters (US qts, lmp. qts)
Drain and refill
w/ Oil filter change 2WD
4WD
w/o Oil filter change 2WD
4WD
Dry fill 2WD
4WD
5.2 (5.5, 4.6)
4.7 (5.0, 4.1)
4.9 (5.2, 4.3)
4.4 (4.7, 3.9)
5.9 (6.2, 5.2)
5.5 (5.8, 4.8)
(c) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR LEAKS
5. RECHECK ENGINE LEVEL