Page 933 of 2062
Downloaded from www.Manualslib.com manuals search engine P02238
Painted Mark
90°90°
EM5292
A
A B
B Seal Width
2 − 3 mm
− ENGINE MECHANICAL (5VZ−FE)CYLINDER BLOCK
EM−105
1996 TOYOTA T100 (RM449U)
(d) Retighten the connecting rod cap nuts 90° as shown.
(e) Check that the painted mark is now at a 90° angle to the
front.
(f) Check that the crankshaft turns smoothly.
(g) Check the connecting rod thrust clearance (See page
EM−92).
12. INSTALL REAR OIL SEAL RETAINER
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the retainer
and cylinder block.
Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing groove.
Thoroughly clean all components to remove all the
loose material.
Using a non−residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the oil seal retainer as shown in the
illustration.
Seal packing:
Part No.08826−00080 or equivalent
Install a nozzle that has been cut to a 2 − 3 mm (0.08
− 0.12 in.) opening.
Parts must be assembled within 5 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.
Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the oil seal retainer with the 6 bolts.
Torque: 8 N·m (80 kgf·cm, 71 in.·lbf)
13. INSTALL OIL PUMP (See page LU−14)
14. INSTALL OIL PAN BAFFLE PLATE
15. INSTALL OIL STRAINER (See page LU−14)
16. INSTALL OIL PAN (See page LU−14)
17. w/ OIL COOLER:
INSTALL OIL COOLER WITH WATER BYPASS HOSE
AND OIL COOLER UNION (See page LU−20)
18. w/o OIL COOLER:
INSTALL OIL HOLE COVER PLATE
Torque: 60 N·m (600 kgf·cm, 44 ft·lbf)
19. INSTALL COOLANT DRAIN COCK
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
20. INSTALL RH AND LH ENGINE MOUNTING BRACKETS
Torque: 44 N·m (440 kgf·cm, 32 ft·lbf)
21. INSTALL OIL FILTER UNION
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
Page 934 of 2062
Downloaded from www.Manualslib.com manuals search engine P00496
Adhesive
P10226
Seal Width
2 − 3 mm EM−106
− ENGINE MECHANICAL (5VZ−FE)CYLINDER BLOCK
1996 TOYOTA T100 (RM449U)
22. INSTALL OIL FILTER (See page LU−3 )
23. INSTALL OIL PRESSURE SWITCH
(a) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No. 08833 − 00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(b) Using SST, install the oil pressure switch.
SST 09816−30010
Torque: 15 N·m (150 kgf·cm, 11 ft·lbf)
24. INSTALL GENERATOR ADJUSTING BAR
Torque: 42 N·m (420 kgf·cm, 31 ft·lbf)
25. INSTALL WATER PUMP (See page CO−7)
26. INSTALL KNOCK SENSORS
Using SST, install the 2 knock sensors.
SST 09816−30010
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
27. INSTALL NO.2 IDLER PULLEY BRACKET
Torque: 38 N·m (380 kgf·cm, 28 ft·lbf)
28. INSTALL WATER BYPASS PIPE WITH KNOCK SEN-
SOR WIRE
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the bypass
and cylinder block.
Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing groove.
Thoroughly clean all components to remove all the
loose material.
Using a non−residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the groove of the bypass pipe.
Seal packing:
Part No. 08826 − 00100 or equivalent
Install a nozzle that has been cut to a 2 − 3 mm (0.08
− 0.12 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.
Page 935 of 2062
Downloaded from www.Manualslib.com manuals search engine P00601
Adhesive
P21461
1
5
3
7
2 68
4
− ENGINE MECHANICAL (5VZ−FE)CYLINDER BLOCK
EM−107
1996 TOYOTA T100 (RM449U)
Parts must be assembled within 5 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.
Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the bypass pipe with the 2 bolts and nut.
Torque: 8.5 N·m (85 kgf·cm, 75 in.·lbf)
(d) Connect the 2 knock sensor connectors.
29. INSTALL CYLINDER HEADS
30. INSTALL PULLEYS AND TIMING BELT
(See page EM−19)
31. REMOVE ENGINE STAND
32. INSTALL REAR END PLATE
Torque: 7.5 N·m (75 kgf·cm, 66 in.·lbf)
33. A/T:
INSTALL DRIVE PLATE
(a) Apply adhesive to 2 or 3 threads of the mount bolt end.
Adhesive:
Part No. 08833 − 00070, THREE BOND 1324 or equiva-
lent
(b) Install the drive plate on the crankshaft.
(c) Install and uniformly tighten the 8 mount bolts in several
passes, in the sequence shown.
Torque: 85 N·m (850 kgf·cm, 63 ft·lbf)
34. M/T:
INSTALL FLYWHEEL
(a) Apply adhesive to 2 or 3 threads of the mount bolt end.
Adhesive:
Part No. 08833 − 00070, THREE BOND 1324 or equiva-
lent
(b) Install the drive plate on the crankshaft.
(c) Install and uniformly tighten the 8 mount bolts in several
passes, in the sequence shown.
Torque: 85 N·m (850 kgf·cm, 63 ft·lbf)
Page 944 of 2062
Downloaded from www.Manualslib.com manuals search engine EC−6
− EMISSION CONTROL (3RZ−FE)EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
934 Author: Date:
1996 TOYOTA T100 (RM449U)
9. CLEAN FILTER IN CANISTER
Clean the filter by blowing 294 kPa (3 kgf·cm
2, 43 psi) of com-
pressed air into tank pipe while holding purge pipe closed
NOTICE:
Do not attempt to wash the canister.
No activated carbon should come out.
10. REINSTALL CAP TO CHARCOAL CANISTER
11. RECONNECT CHARCOAL CANISTER
Torque: 31 N·m (310 kgf·cm, 23 ft·lbf)
12. REINSTALL VSV
Page 946 of 2062
Downloaded from www.Manualslib.com manuals search engine P23481
3−Wa y
Plug
Port Q
Low Vacuum
Z15471
B A
AB
EC−8
− EMISSION CONTROL (3RZ−FE)EXHAUST GAS RECIRCULATION (EGR) SYSTEM
936 Author: Date:
1996 TOYOTA T100 (RM449U)
(b) If you have no TOYOTA hand−held tester, check these
procedures:
(1) Remove the 3−way connector with the vacuum
hose.
(2) Connect the vacuum hose (from port Q of EGR vac-
uum modulator) to the EGR valve.
(3) Plug the vacuum hose (from VSV for EGR).
(c) Check that the vacuum gauge indicates low vacuum at
3,500 rpm.
7. DISCONNECT TOYOTA HAND−HELD TESTER OR
OBDII SCAN TOOL
8. REMOVE VACUUM GAUGE
Remove the vacuum gauge, and reconnect the vacuum hoses
to the proper locations.
9. INSPECT EGR VALVE
(a) Apply vacuum directly to the EGR valve with the engine
idling.
(b) Check that the engine runs rough or dies.
(c) Reconnect the vacuum hoses to the proper locations.
If no problem is found with this inspection, system is normal;
otherwise inspect each part.
10. REMOVE EGR PIPE
Remove the bolt, 4 nuts, EGR pipe and 2 gaskets.
HINT:
Install 2 new gaskets.
Torque:
Bolt: 18 N·m (185 kgf·cm, 13 ft·lbf)
Nut A: 19 N·m (195 kgf·cm, 14 ft·lbf)
Nut B: 20 N·m (200 kgf·cm, 15 ft·lbf)
11. REMOVE EGR VALVE
(a) Disconnect these hoses:
2 Vacuum hoses
2 Water bypass hoses
(b) Remove the 2 nuts, EGR valve and gasket.
Torque: 19 N·m (195 kgf·cm, 14 ft·lbf)
Page 949 of 2062
Downloaded from www.Manualslib.com manuals search engine EC02U−03
P21187
P21181
− EMISSION CONTROL (3RZ−FE)THREE−WAY CATALYTIC CONVERTER (TWC)
SYSTEMEC−11
1996 TOYOTA T100 (RM449U)
REPLACEMENT
1. REMOVE CENTER EXHAUST PIPE
(a) Disconnect the 2 rings from the support bracket.
(b) Remove the 2 nuts and gasket, and disconnect the
heated oxygen sensor (bank 1 sensor 2).
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
HINT:
At the time of assembly please refer to the following item.
Install the heated oxygen sensor with a new gasket.
(c) Remove the 4 bolts, TWC joint retainer, center exhaust
pipe and 2 gasket.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
HINT:
At the time of assembly please refer to the following item.
Place 2 new gaskets on the front exhaust and tail pipes, and
temporarily install the center exhaust pipe.
2. REINSTALL CENTER EXHAUST PIPE
Page 958 of 2062
Downloaded from www.Manualslib.com manuals search engine EC02Z−03
S05202
EC−8
− EMISSION CONTROL (5VZ−FE)EXHAUST GAS RECIRCULATION (EGR) SYSTEM
1996 TOYOTA T100 (RM449U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE EGR PIPE
Remove the 6 nuts, EGR pipe and 2 gaskets.
HINT:
At the time of installation, please refer to the following item.Ins-
tall 2 new gaskets.
Torque:
Nut A: 18.5 N·m (185 kgf·cm, 14 ft·lbf)
Nut B: 8.0 N·m (80 kgf·cm, 71 in.·lbf)
3. REMOVE EGR GAS TEMPERATURE SENSOR
4. REMOVE EGR VALVE
(a) Disconnect these hoses from the EGR valve:
Vacuum hose (from VSV for EGR)
EGR hose (from EGR vacuum modulator)
Water hose (from water bypass pipe)
Water bypass hose (from IAC valve)
(b) Remove the 2 nuts, EGR valve and gasket.
Torque: 18.5 N·m (185 kgf·cm, 14 ft·lbf)
HINT:
Use a new gasket.
At the time of installation, please refer to the following item.
(c) Check for sticking and heavy carbon deposits. If problem
is found, replace the EGR valve.
Page 963 of 2062
Downloaded from www.Manualslib.com manuals search engine EC031−04
P21187
P21181
− EMISSION CONTROL (5VZ−FE)THREE−WAY CATALYTIC CONVERTER (TWC)
SYSTEMEC−13
1996 TOYOTA T100 (RM449U)
REPLACEMENT
1. REMOVE CENTER EXHAUST PIPE
(a) 2WD:
Disconnect the 2 rings from the support bracket.
(b) Remove the 2 nuts and gasket, and disconnect the
heated oxygen sensor (bank 1 sensor 2).
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
HINT:
Use a new gasket.
(c) Remove the 4 bolts, TWC joint retainer, center exhaust
pipe and 2 gasket.
Torque: 48 N·m (490 kgf·cm, 35 ft·lbf)
2. REINSTALL CENTER EXHAUST PIPE
HINT:
Place 2 new gaskets on the front exhaust and tail pipes, and
temporarily install the center exhaust pipe.
