1996 TOYOTA T100 fuel type

Downloaded from www.Manualslib.com manuals search engine SS097−02
SS−18
− SERVICE SPECIFICATIONSMFI (3RZ−FE)
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Fuel line (Union bolt type)2930022
Fuel line (Flare nut type)3031022
Fuel pump bracket assembly x Fuel tank3.94035 in.·lbf
Fuel filter x Cylinder block2020015
Fuel pressure regulator x Delivery pipe8.89078 in.·lbf
Delivery pipe x Cylinder head2121015
Fuel inlet tube x Fuel filter2930022
Fuel inlet tube x Delivery pipe2930022
Air intake chamber x Intake manifold2121015
Throttle body x Air intake chamber2020014
Fuel evaporation tube x Fuel tank1.51513 in.·lbf
Fuel tank filler pipe x Fuel tank3.53531 in.·lbf
Fuel inlet pipe x Body5.45547 in.·lbf
Fuel tank band x Body3940029
MAF meter x Air cleaner cap101007
ECT sensor x Cylinder head2020014
Knock sensor x Cylinder block4445033

Downloaded from www.Manualslib.com manuals search engine SS00V−11
SS−20
− SERVICE SPECIFICATIONSSFI (5VZ−FE)
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Fuel line (Union bolt type)34.335025
Fuel line (Flare nut type)34.335025
Fuel line (Flare nut type) using SST2828521
No. 2 timing belt cover x No. 3 timing belt cover99080 in.·lbf
Fuel inlet pipe x Intake manifold88071 in.·lbf
Delivery pipe x Intake manifold1313010
Fuel pump bracket assembly x Fuel tank3.94035 in.·lbf
Fuel tank band x Body4344032
Fuel tank filler pipe x Fuel tank3.94035 in.·lbf
Fuel evaporation vent tube x Fuel tank1.51513 in.·lbf
Fuel pressure regulator x LH delivery pipe88071 in.·lbf
MAF meter x Air cleaner cap6.97261 in.·lbf
VSV assembly x Air intake connector88071 in.·lbf
A/C idle−up valve x Intake air connector2020014
ECT sensor x Intake manifold2020014
Knock sensor x Cylinder block3940029
EGR gas temperature sensor x EGR valve2020014
Heated oxygen sensor x Front exhaust pipe, Center exhaust pipe2020014

Downloaded from www.Manualslib.com manuals search engine DI−12
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
(b) TOYOTA Enhanced Signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.5 − 4.3 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio
Opening ratio rotary solenoid type IAC valveIdling: 24.8 − 50.0 %
STARTER SIGStarter SignalCranking: ON
CTP SWClosed Throttle Position Switch SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL #1, CYL #2, CYL #3, CYL #4Abnormal revolution variation for each cylinder0 %
IGNITIONTotal number of ignition for every 1,000
revolutions0 − 2,000
EGRT GASEGR Gas Temp. Sensor ValueEGR not operating: Temp. between intake air
temp. and engine coolant temp.
EGR SYSTEMEGR System Operating ConditionIdling: OFF
A/C CUT SIGA/C Cut SignalA/C S/W OFF: ON
FUEL PUMPFuel Pump SignalIdling: ON
EVAP (PURGE) VSVEVAP VSV SignalIdling: OFF
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from lean to rich
Idling after warming up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from rich to lean
Idling after warming up: 0 − 1,000 msec.
*: If no conditions are specifically stated for ”ldling”, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

Downloaded from www.Manualslib.com manuals search engine DI0T8−03
− DIAGNOSTICSENGINE (3RZ−FE)
DI−13
1996 TOYOTA T100 (RM449U)
DIAGNOSTIC TROUBLE CODE CHART
SAE CONTROLLED
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for that code listed
in the table below. For details of each code, turn to the page referred to under the ’’See Page ’’ for the respec-
tive ’’DTC No.’’ in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P0100
(DI−22)Mass Air Flow Circuit
MalfunctionOpen or short in mass air flow meter circuit
Mass air flow meter
ECM

P0101
(DI−26)Mass Air Flow Circuit
Range/Performance
Problem
Mass air flow meter
P0110
(DI−27)Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
Intake air temp. sensor
ECM

P0115
(DI−33)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM

P0116
(DI−38)Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
Cooling system
P0120
(DI−39)Throttle/Pedal Position
Sensor/Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM

P0121
(DI−43)Throttle/Pedal Position
Sensor/Switch ”A” Circuit
Range/Performance Problem
Throttle position sensor
P0125
(DI−44)Insufficient Coolant Temp. for
Closed Loop Fuel ControlOpen or short in heated oxygen sensor (bank 1 sensor 1)
circuit
Heated oxygen sensor (bank 1 sensor 1)

P0130
(DI−47)Heated Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
Fuel trim malfunction
P0133
(DI−50)Heated Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Heated oxygen sensor
P0135
(DI−51)Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 1)Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
 ECM

P0136
(DI−53)Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor
P0141
(DI−51)Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)
Same as DTC No. P0135
*:  MIL lights up

Downloaded from www.Manualslib.com manuals search engine − DIAGNOSTICSENGINE (5VZ−FE)
DI−139
1996 TOYOTA T100 (RM449U)
(b) TOYOTA Enhanced Signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*1
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 1.82 − 3.15 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio
Opening ratio rotary solenoid type IAC valveIdling: 22 − 46 %
STARTER SIGStarter SignalCranking: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N position: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL #1 − CYL #6Abnormal revolution variation for each cylinder0 %
IGNITIONTotal number of ignition for every 1,000
revolutions0 − 3,000
EGRT GAS*2EGR Gas Temp. Sensor Value
EGR not operating:
Temp. between intake air temp. and engine
coolant temp.
EGR SYSTEM*2EGR System Operating ConditionIdling: OFF
A/C CUT SIGA/C Cut SignalA/C S/W OFF: ON
FUEL PUMPFuel Pump SignalIdling: ON
EVAP (PURGE) VSVEVAP VSV SignalVSV operating: ON
VAPOR PRESS VSVVapor Pressure VSV SignalVSV operating: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from lean to rich
Idling after warming up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from rich to lean
Idling after warming up: 0 − 1,000 msec.
*1: If no conditions are specifically stated for ”ldling”, it means the shift lever is at N or P position, the A/C
switch is OFF and all accessory switches are OFF.
*2: Only for 2WD models with a load capacity of 0.5 ton and regular cab.

Downloaded from www.Manualslib.com manuals search engine DI0UC−02
DI−140
− DIAGNOSTICSENGINE (5VZ−FE)
1996 TOYOTA T100 (RM449U)
DIAGNOSTIC TROUBLE CODE CHART
SAE CONTROLLED
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for that code listed
in the table below. For details of each code, turn to the page referred to under the ’’See Page ’’ for the respec-
tive ’’DTC No.’’ in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P0100
(DI−149)Mass Air Flow Circuit
MalfunctionOpen or short in mass air flow meter circuit
Mass air flow meter
ECM

P0101
(DI−153)Mass Air Flow Circuit
Range/Performance
Problem
Mass air flow meter
P0110
(DI−154)Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
Intake air temp. sensor
ECM

P0115
(DI−158)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM

P0116
(DI−162)Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
Cooling system
P0120
(DI−163)Throttle/Pedal Position
Sensor/Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM

P0121
(DI−168)Throttle/Pedal Position
Sensor/Switch ”A” Circuit
Range/Performance Problem
Throttle position sensor
P0125
(DI−169)Insufficient Coolant Temp. for
Closed Loop Fuel ControlOpen or short in heated oxygen sensor (bank 1 sensor 1)
circuit
Heated oxygen sensor (bank 1 sensor 1)

P0130
(DI−172)Heated Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
Fuel trim malfunction
P0133
(DI−175)Heated Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Heated oxygen sensor
P0135
(DI−176)Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 1)Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor
ECM

P0136
(DI−178)Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor
P0141
(DI−176)Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)
Same as DTC No. P0135
*:  MIL lights up

Downloaded from www.Manualslib.com manuals search engine P25779
P21163A00110
− DIAGNOSTICSENGINE (5VZ−FE)
DI−185
1996 TOYOTA T100 (RM449U)
INSPECTION PROCEDURE
1 Check spark plug and spark of misfiring cylinder.
PREPARATION:
(a) Remove the ignition coil and high−tension cord.
(b) Remove the spark plug.
CHECK:
(a) Check the spark plug type.
(b) Check for carbon deposits on electrode.
(c) Check the electrode gap.
OK:
(1) Twin ground electrodes type.
Recommended spark plug:
ND K16TR11
NGK BKR5EKB−11
(2) No large carbon deposit present. Not wet with
gosoline or oil.
(3) Electrode gap: 1.0 − 1.1 mm (0.039 − 0.043 in.)
PREPARATION:
(a) Install the spark plug to the ignition coil or high−tension
cord.
(b) Disconnect the injector connector.
(c) Ground the spark plug.
CHECK:
Check if the spark occurs while the engine is being cranked.
NOTICE:
To prevent excess fuel being injected from the injectors
during this test, don’t crank the engine for more than 5 − 10
sec. at a time.
OK:
Spark jumps across electrode gap.
NG Replace or check ignition system (See page
IG−1).
OK

Downloaded from www.Manualslib.com manuals search engine P15006
Plug
P15007
New Gasket
New
Gasket
FI1654
SST
Fulcrum Length
30 cm
P15750
Grommet
New O−Ring
Delivery PipeCORRECT
WRONG
P15128
Delivery Pipe
Injector
InsulatorO−Ring
Grommet
− MFI (3RZ−FE)MFI SYSTEM
MF−3
955 Author: Date:
1996 TOYOTA T100 (RM449U)
7. FUEL SYSTEM
(a) When disconnecting the high pressure fuel line, a large
amount of gasoline will spill out, so observe these proce-
dures:
(1) Put a container under the connection.
(2) Slowly loosen the connection.
(3) Disconnect the connection.
(4) Plug the connection with a rubber plug.
(b) When connecting the flare nut or union bolt on the high
pressure pipe union, observe these procedures:
(1) (Union Bolt Type)
Always use a new gasket.
(2) (Union Bolt Type)
Tighten the union bolt by hand.
(3) (Union Bolt Type)
Tighten the union bolt to the specified torque.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
(4) (Flare Nut Type)
Apply a light coat of engine oil to the flare and tight-
en the flare nut by hand.
(5) (Flare Nut Type)
Using SST, tighten the flare nut to the specified
torque.
SST 09631−22020
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(c) Observe these precautions when removing and installing
the injectors.
(1) Never reuse the O−ring.
(2) When placing a new O−ring on the injector, take
care not to damage it in any way.
(3) Coat a new O−ring with spindle oil or gasoline be-
fore installing−never use engine, gear or brake oil.
(d) Install the injector to the delivery pipe and cylinder head
as shown in the illustration.