1996 TOYOTA RAV4 air conditioning

FI3605
ONFlashing
0.13 Seconds OFF
DI−6
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
NOTICE:
When simulating symptoms with an OBDII scan tool (Ex-
cluding TOYOTA hand−held tester) to check the DTC, use
normal mode. For codes on the DTC chart subject to ”2 trip
detection logic”, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTC are recorded in
the ECM.
3. INSPECT DIAGNOSIS (Check Mode)
HINT:
TOYOTA Hand−Held Tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC.
(1) Initial conditions.
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in park or neutral position.
Air conditioning switched OFF.
(2) Turn ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand−held tester to DLC3 at
the lower of the instrument panel.
(5) Turn the ignition switch ON and push the TOYOTA
hand−held tester main switch ON.
(6) Switch the TOYOTA hand−held tester normal mode
to check mode. (Check that the MIL flashes.)
(7) Start the engine. (The MIL goes out after the engine
starts.)
(8) Simulate the conditions of the malfunction de-
scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc.
(9) After simulating the malfunction conditions, use the
TOYOTA hand−held tester diagnosis selector to
check the DTC and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. Turning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all diagnostic codes, etc. are erased.

P00495
Outside
Inside
− DIAGNOSTICSENGINE
DI−9
1996 RAV4 (RM447U)
4 Check air filter.
PREPARATION:
Remove air filter.
CHECK:
Visually check that the air cleaner element is not excessively
dirty or oily.
HINT:
If necessary, clean element with compressed air.
First blow from inside thoroughly,then blow from outside of ele-
ment.
NG Repair or replace.
OK
5 Check idle speed.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Switch off all accessories.
(c) Switch off air conditioning.
(d) Shift transmission into ”N” position.
(e) Connect the OBDII scan tool or TOYOTA hand−held tes-
ter to DLC3 on the vehicle.
CHECK:
Use CURRENT DATA to check the engine idle speed.
OK:
Idling speed: 650 − 750 rpm
NG Proceed to matrix chart of problem symptoms
on page DI−20.
OK

S02412
A/C Amplifier
B+
R−Y
E621
ACTECM
E1 7 DI−122
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
A/C Cut Control Circuit
CIRCUIT DESCRIPTION
This circuit cuts air conditioning operation during vehicle acceleration in order to increase acceleration per-
formance. During acceleration with the vehicle speed at 25 km/h (16 mph) or less, engine speed at 1,200
rpm or less and throttle valve opening angle at 60° or more, the A/C magnet switch is turned OFF for several
seconds.
WIRING DIAGRAM
DI408−01

− DIAGNOSTICSENGINE
DI−123
1996 RAV4 (RM447U)
INSPECTION PROCEDURE
TOYOTA hand−held tester:
1 Connect the TOYOTA hand−held tester and check operation of air conditioning
cut control.
PREPARATION:
(a) Connect the TOYOTA hand−held tester to the DLC3.
(b) Turn ignition switch ON and TOYOTA hand−held tester main switch ON.
(c) Starter the engine and air conditioning switch ON.
HINT:
A/C magnet clutch is turned ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand−held tester.
CHECK:
Check operation of A/C magnet clutch cut when air conditioning cut control is operated by the TOYOTA
hand−held tester.
OK:
A/C magnet clutch is turned OFF.
OK Proceed to next circuit inspection shown on
matrix chart (See page DI−20).
NG
2 Check for open and short in harness and connector between ECM and A/C am-
plifier (See page IN−30).
NG Repair or replace harness or connector.
OK

FI3605
013 sec. ON
OFF
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A241E)
DI−129
1996 RAV4 (RM447U)
(5) See page DI−138 to confirm the details of the
DTCs.
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand−held tester) to check the DTCs, use
the normal mode. For codes on the DTC chart subject to ”2
trip detection logic”, turn the ignition switch off after the
symptoms have been simulated for the first time. Then re-
peat the simulation process again. When the program has
been simulated twice, the MIL lights up and the DTCs are
recorded in the ECM.
3. Check Mode:
INSPECT DIAGNOSIS
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has high sens-
ing ability to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC.
(1) Initial conditions.
Battery positive voltage 11 V or more
Throttle valve fully closed
Transaxle in the PARK position
Air conditioning switched off
(2) Prepare the TOYOTA hand−held tester.
(3) Connect the TOYOTA hand−held tester to the
DLC3.
(4) Turn the ignition switch ON and switch the TOYOTA
hand−held tester ON.
(5) Switch the TOYOTA hand−held tester from the nor-
mal mode to the check mode (Check that the MIL
flashes.).
(6) Start the engine (The MIL goes off after the engine
start.).
(7) Simulate the conditions of the malfunction de-
scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTCs, etc.
(8) After simulating the malfunction conditions, use the
TOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF.
Turning the ignition switch off switches the diagnosis system
from check mode to normal mode, so all DTCs, etc. are erased.
(9) After checking the DTC, inspect the applicable cir-
cuit.

FI3605
ON
OFF
0.13 sec.
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A540H)
DI−175
1996 RAV4 (RM447U)
(5) See page DI−189 to confirm the details of the
DTCs.
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand−held tester) to check the DTCs, use
the normal mode. For codes on the DTC chart subject to ”2
trip detection logic”, turn the ignition switch off after the
symptoms have been simulated for the first time. Then re-
peat the simulation process again. When the program has
been simulated twice, the MIL lights up and the DTCs are
recorded in the ECM.
3. Check Mode:
INSPECT DIAGNOSIS
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has high sens-
ing ability to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC.
(1) Initial conditions.
Battery positive voltage 11 V or more.
Throttle valve fully closed
Transaxle in the PARK position
Air conditioning switched off
(2) Prepare the TOYOTA hand−held tester.
(3) Connect the TOYOTA hand−held tester to the
DLC3.
(4) Turn the ignition switch ON and switch the TOYOTA
hand−held tester ON.
(5) Switch the TOYOTA hand−held tester from the nor-
mal mode to the check mode (Check that the MIL
flashes.).
(6) Start the engine (The MIL goes off after the engine
start.).
(7) Simulate the conditions of the malfunction de-
scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTCs, etc.
(8) After simulating the malfunction conditions, use the
TOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. Turning the ignition
switch off switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased.
(9) After checking the DTC, inspect the applicable cir-
cuit.

EM0EK−01
EM−12
− ENGINE MECHANICALIDLE SPEED
1996 RAV4 (RM447U)
IDLE SPEED
INSPECTION
1. INITIAL CONDITIONS
(a) Engine at normal operating temperature
(b) Air cleaner installed
(c) All pipes and hoses of air induction system connected
(d) All vacuum lines properly connected
(e) SFI system wiring connectors fully plugged
(f) All operating accessories switched OFF
(g) Ignition timing check correctly
(h) Transmission in neutral position
(i) Air conditioning switched OFF
2. CONNECT TOYOTA HAND−HELD TESTER OR OBD II SCAN TOOL (See page EM−11)
3. INSPECT IDLE SPEED
(a) Race the engine speed at 2,500 rpm for approx. 90 seconds.
(b) Check the idle speed.
Idle speed (w/ Cooling fan OFF): 750 ± 50 rpm
If the idle speed is not as specified, check the IAC valve and air intake system.
4. DISCONNECT TOYOTA HAND−HELD TESTER OR OBD II SCAN TOOL

15
ABBREVIATIONS D
ABBREVIATIONS
The following abbreviations are used in this manual.
ABS = Anti-Lock Brake System
A/C = Air Conditioning
A/T = Automatic Transaxle
COMB. = Combination
DIFF. = Differential
ECU = Electronic Control Unit
EGR = Exhaust Gas Recirculation
EVAP = Evaporative Emission
J/B = Junction Block
LH = Left-Hand
M/T = Manual Transaxle
O/D = Overdrive
R/B = Relay Block
RH = Right-Hand
SFI = Sequential Multiport Fuel Injection
SRS = Supplemental Restraint System
SW = Switch
TEMP. = Temperature
VSV = Vacuum Switching Valve
w/ = With
w/o = Without
2WD = Two Wheel Drive
4WD = Four Wheel Drive
* The titles given inside the components are the names of the terminals (terminal codes) and are not
treated as being abbreviations.