1996 TOYOTA LAND CRUISER fuse diagram

I00491
Cruise Control ECU
C17
Speedometer
(Combination Meter)
C13
C13
4 3
Vehicle Speed Sensor (Combination Meter) R−O
R−O
R−G
R−G 25
1
Ea1EC1
IH1L−W
BR Air Intake Chamber
EC
V1
V1
V13 2
1
1
Ea1 EC1
3 6
Y
Y GAUGE
AM1
Y
Y
BR
BR
EC1
Ea1 IH1
22
Instrument Panel Fuse
Block
Fusible Link BatteryWB
B
I12
I12
Ignition Switch 2
4
1
3
F11
F11Y
B
B
J4
JUNCTION
CONNECTOR
EA1
6
2
2 3
4
B−L
FL MAIN
F6
1 B−Y
39
20
SPD
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−307
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Input SignalIndicator Light
Blinking Pattern
Stop Light
switch ON
Light ON
OFF SW OFF
SW ON
DI−314
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Stop Light Switch Circuit
CIRCUIT DESCRIPTION
When the brake pedal is depressed, the stop light switch sends a signal to th\
e ECU. When the ECU receives
this signal, it cancels the cruise control.
A fail− safe function is provided so that the cancel functions normally , even if there is a malfunction in the stop
light signal circuit.
The cancel conditions are: Battery positive voltage at terminal STP −
When the brake is on, battery positive voltage normally applies through the S\
TOP fuse and stop light switch
to terminal STP− of the ECU, and the ECU turns the cruise control off.
If the harness connected to terminal STP − has an open circuit, terminal STP − will have battery positive volt-
age and the cruise control will be turned off.
Also, when the brake is on, the magnetic clutch circuit is cut mechanically \
by the stop light switch, turning
the cruise control off (See page DI−298 for operation of the magnetic clutch).
WIRING DIAGRAM
See page DI−298 .
INSPECTION PROCEDURE
1 Check operation of stop light.
CHECK:
Check that stop light comes on when brake pedal is depressed, and turns off when brake pedal is released.
NG Check stop light system (See page BE−24 ).
OK
2 Input signal check.
CHECK:
(a) See input signal check on DI−286.
(b) Check the indicator light when the brake pedal is de-
pressed.
OK:
The indicator light goes off when the brake pedal is
depressed.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
DI5OI−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00495
Cruise Control ECUD
2
Y Y
B
B 4
Instrument Panel Fuse Block B−O
IH1
1 3
6
B−O
GAUGE
9
2 4
Ignition Switch C17
B−Y FL AM1 AM1
EA2 2
1
B
B 6
Battery 2
1 W
2 2
B−L
A/T Indicator Light
(Park/Neutral Position Switch)
IH24
P1
P1
F11 F11 J4
JUNCTION
CONNECTOR
I12 I12 Fusible Link
F6 2
D
Fusible Link
Y
DI−322
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Park/Neutral Position Switch Circuit
CIRCUIT DESCRIPTION
When the shift position is put in except D position, a signal is sent from t\
he park/neutral position switch to
the ECU. When this signal is input during cruise control driving, the EC\
U cancels the cruise control.
WIRING DIAGRAM
DI5OL−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00496
Cruise Control ECU
Fusible Link Fusible Link
Battery BR
BR
Instrument
Panel Fuse Block
ECU−IG
Ignition Switch BB
2
4 3
2
F6
1 JUNCTION
CONNECTOR J6
C17
C17B−W
I12
I12 4
2
2
2
2 B−W
F11
F11
B
B−Y
B
6EA2B
GND
13
14
AM1
FL AM1
1
ID
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−325
1996 LAND CRUISER (RM451U)
ECU Power Source Circuit
CIRCUIT DESCRIPTION
The ECU power source supplies power to the actuator and sensors, etc.. When\
terminal GND and the cruise
control ECU case are grounded.
WIRING DIAGRAM
DI5OM−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00497
Cruise Control ECU
B−R BATT
C17
W
W Instrument Panel Fuse Block
Fusible Link
F8 F11
F11
EA3
FL MAIN
Battery 3
ECU−B 15
2
1
N18670
Junction Block No.1
ECU−IG
Fuse
DI−328
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Back −up Power Source Circuit
CIRCUIT DESCRIPTION
The ECU back− up power source provides power even when the ignition is off and is used for DTC memory,
etc..
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check ECU −IG fuse.
PREPARATION:
Remove the ECU −IG fuse from relay block No.2.
CHECK:
Check continuity of ECU −IG fuse.
OK:
Continuity
NG Check for short in all the harness and compo- nents connected to the ECU −IG fuse.
OK
DI5ON−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00498
Cruise Control ECU
C17
Battery Fusible
Link
F6 B−L W
B
B G−Y
F11 F11
GAUGE
Y
2
Y9
CRUISE MAIN Indicator (Combination Meter)C10
C10
2 2 2
2
22
43
EA2
6
Ignition Switch
I12 I12
4
Instrument Panel Fuse Block
1
AM1
AM1 J1
JUNCTION
CONNECTOR
PI
7
DI−332
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
CRUISE MAIN Indicator Light Circuit
CIRCUIT DESCRIPTION
When the cruise control main switch is turned ON, CRUISE MAIN indicator ligh\
t lights up.
WIRING DIAGRAM
DI5OP−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010