1996 TOYOTA LAND CRUISER Cruise control

I00495
Cruise Control ECUD
2
Y Y
B
B 4
Instrument Panel Fuse Block B−O
IH1
1 3
6
B−O
GAUGE
9
2 4
Ignition Switch C17
B−Y FL AM1 AM1
EA2 2
1
B
B 6
Battery 2
1 W
2 2
B−L
A/T Indicator Light
(Park/Neutral Position Switch)
IH24
P1
P1
F11 F11 J4
JUNCTION
CONNECTOR
I12 I12 Fusible Link
F6 2
D
Fusible Link
Y
DI−322
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Park/Neutral Position Switch Circuit
CIRCUIT DESCRIPTION
When the shift position is put in except D position, a signal is sent from t\
he park/neutral position switch to
the ECU. When this signal is input during cruise control driving, the EC\
U cancels the cruise control.
WIRING DIAGRAM
DI5OL−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Input SignalIndicator Light
Blinking Pattern
Turn PNP switch
OFF (Shift to
except D position)
LightON
OFF SW ON
SW OFF
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−323
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check starter operation.
CHECK:
Check that the starter operates normally and that the engine starts.
NG Proceed to engine troubleshooting (See page DI−1).
OK
2 Input signal check.
PREPARATION:
See input signal check on page DI−286.
CHECK:
Check the indicator light when shifting into except D position.
OK:
The indicator light goes off when shifting into except
D position.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0119I00017 I00026
ON
D
(−)
(+)
DI−324
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
3 Check voltage between terminal D of cruise control ECU connector and body
ground.
PREPARATION:
Turn ignition switch ON.
CHECK:
Measure voltage between terminal D of ECU connector and
body ground when shifting into D position and other positions.
OK:
Shift PositionVoltage
D position10 − 14 V
Other positionsBelow 1 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−295 ).
NG
4 Check harness and connector between cruise control ECU and park/neutral position switch (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU (See
page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00496
Cruise Control ECU
Fusible Link Fusible Link
Battery BR
BR
Instrument
Panel Fuse Block
ECU−IG
Ignition Switch BB
2
4 3
2
F6
1 JUNCTION
CONNECTOR J6
C17
C17B−W
I12
I12 4
2
2
2
2 B−W
F11
F11
B
B−Y
B
6EA2B
GND
13
14
AM1
FL AM1
1
ID
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−325
1996 LAND CRUISER (RM451U)
ECU Power Source Circuit
CIRCUIT DESCRIPTION
The ECU power source supplies power to the actuator and sensors, etc.. When\
terminal GND and the cruise
control ECU case are grounded.
WIRING DIAGRAM
DI5OM−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N18670
Junction Block No.1ECU−B
Fuse
AB0119I00014 I00027
GNDB
ON
(−)
(+)
DI−326
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check ECU −B fuse.
PREPARATION:
Remove the ECU −B fuse from instrument panel fuse block.
CHECK:
Check continuity of ECU −B fuse.
OK:
Continuity
NG Check for short in all the harness and compo- nents connected to ECU−B fuse.
OK
2 Check voltage between terminals B and GND of cruise control ECU connecto\
r.
PREPARATION:
(a) Remove the ECU with connector still connected.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals B and GND of ECU con-
nector.
OK:
10 − 14 V
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00018
GND
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−327
1996 LAND CRUISER (RM451U)
3 Check resistance between terminal GND of cruise control ECU connector and
body ground (See page IN−28).
CHECK:
Measure resistance between terminal GND of ECU connector
and body ground.
OK:
Resistance: Below 1 Ω
NG Repair or replace harness or connector.
OK
Check and repair harness and connector be-
tween cruise control ECU and battery
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00497
Cruise Control ECU
B−R BATT
C17
W
W Instrument Panel Fuse Block
Fusible Link
F8 F11
F11
EA3
FL MAIN
Battery 3
ECU−B 15
2
1
N18670
Junction Block No.1
ECU−IG
Fuse
DI−328
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Back −up Power Source Circuit
CIRCUIT DESCRIPTION
The ECU back− up power source provides power even when the ignition is off and is used for DTC memory,
etc..
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check ECU −IG fuse.
PREPARATION:
Remove the ECU −IG fuse from relay block No.2.
CHECK:
Check continuity of ECU −IG fuse.
OK:
Continuity
NG Check for short in all the harness and compo- nents connected to the ECU −IG fuse.
OK
DI5ON−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00016
BATT
(−)
(+)
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−329
1996 LAND CRUISER (RM451U)
2 Check voltage between terminal BATT of cruise control ECU connector and body
ground (See page IN−28).
PREPARATION:
Remove the ECU with connector still connected.
CHECK:
Measure voltage between terminal BATT of ECU connector
and body ground.
OK:
Voltage: 10 − 14 V
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
Check and repair harness and connector be-
tween battery and cruise control ECU
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010