1996 TOYOTA LAND CRUISER Cruise control

W02195
ECU−IG
Ignition Switch
GNDABS ECU
B−W
J6
Junction
Connector
W
B−L
6
EA2
AM1
IE
3 4
Deceleration
Sensor
2
2
2
2 2
2
2
A13
A13 A13
Battery
AM1
GND
B−W
B−Y
B
B
BB
B
BR BR
BR
F6 1
1
13
+B
12
15
4 R/B No. 2
R/B No. 2
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−215
1996 LAND CRUISER (RM451U)
DTC 41 IG Power Source Circuit
CIRCUIT DESCRIPTION
This is the power source for the ECU, hence the CPU and actuators.
DTC No.DTC Detecting ConditionTrouble Area
41
Vehicle speed is 3 km/h (1.9 mph) or more and voltage of
ECU terminal IG1 remains at more than 17 V or below 9.5
V for more than 10 sec.Battery
 IC regulator
 Open or short in power source circuit
Fail safe function:
If trouble occurs in the power source circuit, the ECU cuts off current to the ABS control (solenoid) relay and
prohibits ABS control.
WIRING DIAGRAM
DI5M4−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02196
BF
6
ECU−IG Y
Junction
Connector ABS ECU
W−B Y−B
4
2 3
1
Deceleration
Sensor
A12
ABS ECU
GS1
GS2 GST
A22
3
B−W
Y
B−W
B−W
A22A22 A22
A22
A12
A12
12
10
12 13 14
15
Y−RY−R
Y−B
B
B
B 12 V
12 V
ID3
ID3
ID3
ID2
3
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−219
1996 LAND CRUISER (RM451U)
DTC 44 Deceleration Sensor Circuit
CIRCUIT DESCRIPTION
This sensor detects deceleration on the vehicle. The sensor signal is used in ABS control. If the sensor func-
tions abnormally, the ABS warning light comes on but the ABS still operates.
DTC No.DTC Detecting ConditionTrouble Area
44
Either of the following 1 or 2 is detected:
1. An open or short is detected in circuit GS1 or GS2 for
1sec.
2. After the ignition is turned ON, the test signal is output by GST
During this time, a trouble signal is detected for 0.5 sec.
Deceleration sensor
 Open or short in deceleration sensor circuit
WIRING DIAGRAM
DI5M8−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02192
22 1
4
ABS
R/B
No. 2
W
B−R
W−B
ID
1 1
1
2
2
2
3
64
4 3
6
3
511
18
G
G−B
G−Y
DLC1 ABS ECU
MR
R−
SR
AST MT
L−Y
L−W
ABS Actuator ABS Control Relay
Motor
Relay
Solenoid
Relay
ABS ECU
A6A4
A13A5
F6
Battery
B−L
2
2
12 B−W
B−W
B−W
EA312
5
A5
A4
A4 A6
A6
A6
A7
A7
A7 A7A13 A13
A13 A13
24
23
B−L
EA312 V 12 V
B−W
AM1
W−B W−B
R/B
No. 2 B−W
DI−224
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
DTC 51 ABS Pump Motor Lock
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
51Pump motor is not operating normally during initial checkABS pump motor
Fail safe function:
If trouble occurs in the ABS pump motor, the ECU cuts off current to the ABS control (solenoid) relay and
prohibits ABS control.
WIRING DIAGRAM
DI5MB−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02195
ECU−IG
Ignition Switch
GNDABS ECU
B−W
J6
Junction
Connector
W
B−L
6
EA2
AM1
IE
3 4
Deceleration
Sensor
2
2
2
2 2
2
2
A13
A13 A13
Battery
AM1
GND
B−W
B−Y
B
B
BB
B
BR BR
BR
F6 1
1
13
+B
12
15
4 R/B No. 2
R/B No. 2
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−225
1996 LAND CRUISER (RM451U)
DTC Always ON Malfunction in ECU
IG Power Source Circuit
CIRCUIT DESCRIPTION
This is the power source for the ECU, hence the CPU, and the actuator.
DTC No.DTC Detecting ConditionTrouble Area
Alway ONVoltage of ECU terminal +B remains at more than 17 V or
below 9.5 V
Battery
 IC regulator
 Open or short in power source circuit
 ECU
Fail safe function:
If trouble occurs in the power source circuit, the ECU cuts off current to the ABS control (solenoid) relay and
prohibits ABS control.
WIRING DIAGRAM
DI5ME−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02199
BatteryJunction
Connector
ID
W−B
B−W
ABS Control Relay
1 4
2
6 3
1
4
Motor
Relay
Solenoid
Relay
ABS ECU
ABS ECU
ABS Actuator 4
5
A7
A6
A6 A6
A4 R−L
R−L
DLC1
Short Pin
B−W
IH1
A12
ABS ECU
W
13
C10
GAUGE
2223 ABS
Warning
Light
A
A
J1
C10IH1
20
A7
A7A7
A7
EA3
EA3
2
1 B−W
B−W
B−L OO
O
Y
54
3
23 OY
DI−230
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
ABS Warning Light Circuit
CIRCUIT DESCRIPTION
If the ECU detects trouble, it lights the ABS warning light while at the same time prohibiting ABS control. At
this time, the ECU records a DTC in memory. After removing the short pin of the DLC1, connect terminals
Tc and E
1 of the DLC1 to make the ABS warning light blink and output the DTC.
WIRING DIAGRAM
INSPECTION PROCEDURE
Troubleshooting in accordance with the chart below for each trouble symptom.
ABS warning light does not light upGo to step 1
ABS warning light remains onGo to step 3
1 Check ABS warning light.
See Combination Meter Troubleshooting on page BE−2.
NG Repair bulb or combination meter assembly.
OK
DI5MJ−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R14139
A6A7
Continuity
Continuity Open
1
2
5
6
3
R14140
A7
A6
(−)
(+)
Continuity
Open
1
2
5
6
3
R14144
(+) (−)4
5
A7A6
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−231
1996 LAND CRUISER (RM451U)
2 Check ABS control relay.
PREPARATION:
(a) Turn the ignition switch OFF.
(b) Disconnect the connectors from the control relay.
CHECK:
Check the continuity between each terminal of the ABS control
relay.
OK:
Terminals A7 −1 and A6− 3Continuity
(Reference value 80 Ω)
Terminals A7 −5 and A7− 6Continuity
Terminals A7 −2 and A7− 5Open
CHECK:
(a) Apply battery positive voltage between terminals A7 −1
and A6−3.
(b) Check the continuity between each terminal of the ABS control relay.
OK:
Terminals A7 −5 and A7− 6Open
Terminals A7 −2 and A7− 5Continuity
CHECK:
Connect the  test lead to terminal A7−4 and the  test lead
to terminal A7−5. Check continuity between the terminals.
OK:
Continuity
If there is no continuity, connect the  test lead to terminal A7−4
and the  lead to terminal A7 −5. Recheck continuity between
terminals.
NG Replace ABS control relay.
OK
Check for open in harness and connector be-
tween DLC1 and ABS control relay and body
ground (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−232
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
3 Is DTC output?
Check DTC on page DI−190 .
YES Repair circuit indicated by code output.
NO
4 Does ABS warning light go off if short pin is removed?
NO Check for short in harness and connector be- tween warning light and DLC1 and ECU (See
page IN−28 ).
YES
5 Check ABS control relay (See step 2).
NG Replace ABS control relay.
OK
Check for short in harness and connector be-
tween DLC1 and ABS control relay (See page
IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R14285 AB0119H00021
Airbag Sensor Assembly
ON
IG2
ACC
(+)
(−)
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−265
1996 LAND CRUISER (RM451U)
DTC 31 Airbag Sensor Assembly Malfunction
CIRCUIT DESCRIPTION
The airbag sensor assembly consists of a airbag sensor, safing sensor, drive circuit, diagnosis circuit and
ignition control, etc.
It receives signals from the airbag sensors, judges whether or not the SRS must be activated, and diagnosis
system malfunction.
DTC 31 is recorded when occurrence of a malfunction in the airbag sensor\
assembly is detected.
DTC No.DTC Detection ConditionTrouble Area
31 Airbag sensor assembly malfunctionAirbag sensor assembly
INSPECTION PROCEDURE
HINT:
When a malfunction code other than code 31 is displayed at the same time, fi\
rst repair the malfunction indi-
cated by the malfunction code other than code 31.
1 Preparation (See step 1 on page DI−271).
2 Check voltage at IG2 and ACC of airbag sensor assembly.
PREPARATION:
Turn ignition switch ON.
CHECK:
Measure voltage between terminals IG2 and ACC of airbag
sensor assembly and body ground.
OK:
Voltage: Below 16 V
NG Check battery and charging system (See page CH−2).
OK
DI5QA−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010